Z3X Pandora PRO 7.4 / 7.5 Released. New devices functions added

[mahi_mobile]

Pandora_setup_7.5_(www.gsmfirmwareteam.com) | Gsm Firmware Team

 

[oraltect]

Selected model: Tecno KJ5 (Tecno Spark 20)
Operation: Eliminar FRP
Software version: 7.4

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX or PC] in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM_V1632 (Android),usb2ser.sys,3.0.1504.0]
Device found at COM2 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0x4881FE52, 0xBE1C041E, 0xFD848545, 0x91CB64A8
Load DownloadAgent... OK
Search DA... OK [0]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [PRELOADER]
Preloader alive. Skip initializing external RAM
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: MMC256
EMMC_ID : 0xD62D004D4D4338289A7523536511513D
EMMC_BOOT1: 0x0000400000 (4,00Mb)
EMMC_BOOT2: 0x0000400000 (4,00Mb)
EMMC_RPMB : 0x0000400000 (4,00Mb)
EMMC_USER : 0x3A40A00000 (233,01Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448,00Kb)
EXT_RAM : 0x0100000000 (4,00Gb)
Checking USB status... USB_HIGH_SPEED
[EFUSE INFO]: BROM not disabled
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EROFS] ... OK
Product Brand : TECNO
Product Manufacturer : TECNO
Product Model : TECNO KJ5
Product Name : KJ5-OP
Product Device : TECNO-KJ5
Product Board : TECNO-KJ5
Board Platform : mt6768
Build ID : SP1A.210812.016
Build Date : Mon Jul 22 16:13:37 CST 2024
Display ID : TECNO-T-64-240722V1145
Security Patch : 2024-07-05
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : 240722V1315
Userdata FS Type : F2FS
Switch to BROM
Read partition "preloader"... OK
Read partition "preloader_backup"... OK
Parse scatter file... OK
Load Rom Images... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to [BOX] in BROM mode
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0707
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM2 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x4881FE52, 0xBE1C041E, 0xFD848545, 0x91CB64A8
Get Chip ID... [MT6768]
Get SOC ID... [FBD8B2D865985145E56122349E9EA84AD7 9D7A8764C02DC80F8746557E1534CA]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [8]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0xD62D004D4D43328289A753536511513D
Load EMI from file... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: MMC256
EMMC_ID : 0xD62D004D4D43328289A753536511513D
EMMC_BOOT1: 0x0000400000 (4,00Mb)
EMMC_BOOT2: 0x0000400000 (4,00Mb)
EMMC_RPMB : 0x0000400000 (4,00Mb)
EMMC_USER : 0x3A40A00000 (233,01Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448,00Kb)
EXT_RAM : 0x0100000000 (4,00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Restore parts:
Write file "preloader_kj5_h6931.bin"... OK
Write file "preloader_kj5_h6931_backup.bin"... OK
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Tecno_KJ5%20(Tecno%20Spark%2020)/FRP_BACKUP_(2024-9-21_12-33-56)/
Format FRP... [P1] OK
Writting FRP data... OK
Fix TOOL DL Image error... OK
Erase FRP done!

Not well enough working it kill some

 

[GsmToto]

Selected model: Tecno CG6j (Tecno Camon 17)
Operation: Erase FRP And Wipe
Software version: 7.5
Erasing of partitions can damage your device.
Make sure that you have a backup created. Continue? YES

Connect phone in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM (Android),usb2ser.sys,3.0.1504.0]
Device found at COM3 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0xE1F48CC2, 0x31159CC5, 0x192DD411, 0x7D003D33
Load DownloadAgent... OK
Search DA... OK [1]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [PRELOADER]
Preloader alive. Skip initializing external RAM
Send preloader... OK
Load DownloadAgent... OK
Search DA... OK [8]
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: hDEaP3
EMMC_ID : 0x90014A68444561503303003137A86233
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x1D1F000000 (116.48Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: info not available
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
[EFUSE INFO]: BROM not disabled
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : TECNO
Product Manufacturer : TECNO MOBILE LIMITED
Product Model : TECNO CG6j
Product Name : CG6j-OP
Product Device : TECNO-CG6j
Product Board : TECNO-CG6j
Board Platform : mt6768
Build ID : SP1A.210812.016
Build Date : Thu Apr 20 21:03:19 CST 2023
Display ID : TECNO-S-64-230420V876
Security Patch : 2023-04-05
Version SDK : 31
Version Release : 12
Version Codename : REL
Firmware Version : 230420V1000
Userdata FS Type : F2FS
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Tecno_CG6j%20(Tecno%20Camon%2017)/FRP_BACKUP_(2024-9-24_17-32-54)/
Format FRP... [P1] OK
Writting FRP data... OK
Formatting "userdata" partition... OK
Formatting "metadata" partition... OK
Formatting "md_udc" partition... OK
Wipe data done!

 

[pooltec]

Error de reparación de imei OPPO RENO 10 5G

Apagado del host... OK
Cambiar puerto virtual a NINGUNO... OK
Conectar Tipo-C a HUB... OK
Encender el host... OK
Conectar teléfono a [BOX o PC] en modo PRELOADER
Esperando dispositivo... OK
Controlador: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM_V1632 (Android),usb2ser.sys,3.0.1504.0]
Dispositivo encontrado en COM32 [PRELOADER]
Abrir puerto... OK
Enviar comando de inicio... OK
Obtener código HW del dispositivo... 0959
Obtener configuración seg... OK [00000005]
Banderas sec activas: [SBC DAA]
Obtener la versión HW y SW del dispositivo... OK
VER HW: CA00, VER SW: 0000, CÓDIGO SUB HW: 8A00
Chip detector [MT6877]
Versión de la biblioteca [2]
Seleccionar plataforma... OK
Inicializar BROM... OK
Forzar carga... OK
Deshabilitar temporizador WatchDog... OK
Reabrir puerto para libver2... OK
Precargador existente. Omitir verificación de conexión.
Obtener mi ID... OK
Identidad_mínima = 0x3097BD7C, 0x41C02175, 0x8A1BCCCD, 0xB744C14D
Cargar DownloadAgent... OK
Buscar DA... OK [0]
Enviar cargador de arranque... OK
Iniciar cargador de arranque... OK
Esperar respuesta del cargador de arranque... OK
Enviar señal SYNC... OK
Configurar entorno del dispositivo... OK
Configurar parámetros del dispositivo... OK
Recibir señal SYNC de DA... OK
Establecer parámetros de DA... OK
Obtener agente de conexión del dispositivo... [PRELADER]
Precargador activo. Omitir inicialización de RAM externa
Enviar precargador... OK
Cargar DownloadAgent... OK
Buscar DA... OK [17]
Enviar 2.º DA... OK
Obtener información del dispositivo... OK
INFORMACIÓN UFS:
Identificador de usuario: H9QT1G6DN6X132
UFS_FWVER: A003
TAMAÑO_BLOQUE: 0x0000001000 (4,00 Kb)
UFS_LU0: 0x0000400000 (4,00 Mb)
UFS_LU1: 0x0000400000 (4,00 Mb)
UFS_LU2: 0x3B96000000 (238,34 GB)
INFORMACIÓN RAM:
INT_SRAM: 0x0000070000 (448,00 Kb)
RAM_EXTERIOR: 0x0200000000 (8,00 Gb)
SALUD:
Información Pre EOL: normal
DeviceLifeTimeEstA: 0% - 10% tiempo de vida útil del dispositivo usado
DeviceLifeTimeEstB: 0% - 10% tiempo de vida útil del dispositivo usado
Comprobando estado de USB... USB_HIGH_SPEED
[EFUSE INFO]: BROM no deshabilitado
Leyendo información de particiones del teléfono... OK
Comprobando estado A/B... OK
Leer información del producto... [EROFS] ... OK
Marca del producto: OPPO
Fabricante del producto: OPPO
Modelo del producto: CPH2531
Nombre del producto: CPH2531
Dispositivo del producto: OP5705L1
Placa del producto: k6877v1_64_k419
Plataforma de placa: mt6877
ID de compilación: SP1A.210812.016
Fecha de compilación: jue., 25 de abril de 2024, 10:44:59 CST
ID de pantalla: CPH2531_14.0.0.600(EX01)
Parche de seguridad: 2024-04-05
Versión SDK: 34
Versión lanzada: 14
Nombre en código de la versión: REL
Versión de firmware: T.R4T2.17c8306-c8af
Datos de usuario Tipo de FS: F2FS
Leer partición de seguridad del teléfono...
Descifrando
datos de seguridad... OK Cifrar datos de seguridad... OK
Leer partición "nvdata"... OK
Leer partición "protect1"... OK
Leer partición "nvram"... OK
Leer archivos NVDATA... OK
Leer archivos NVRAM... OK
Leer archivos de seguridad... OK
Calculando... OK
Reparando IMEI...
Número IMEI 1: 865859069413899
Número de serie 2: 865859063470671
Escribir IMEI y parchar CERT [NVDATA]... OK
Comprobando tipo de parche... parche imposible



Modelo seleccionado: OPPO CPH2531 (Oppo Reno10 (China) 5G)
Operación: Reparar
Versión del software: 7.4

 

[samsameer]

pandora team....vivo security...2024..not support..plzz new update

 

[bilaltariq222]

F936U BiT 6 loader not working

 

[bilaltariq222]

N986U Bit 9 also not working

 

[abdoullaye]

Please fix this error


Selected model: Tecno KI7 (Tecno Spark 10 Pro)
Operation: Flash (Download only)
Software version: 7.5
If BROM was disabled and you want write preloader partition not compatible for this model, phone will bricked. Recovery possible only with ISP mode.
Continue? YES
Work ID: 43607963

Parse scatter file... OK
Load Rom Images... OK
Connect phone in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM (Android),usb2ser.sys,3.0.1504.0]
Device found at COM10 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0xD2A916EF, 0x4FD1B488, 0x18241B33, 0x256C5988
Load DownloadAgent... OK
Search DA... OK [0]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [PRELOADER]
Preloader alive. Skip initializing external RAM
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: MMC128
EMMC_ID : 0xD62D004D4D43313238510F73578A2A87
EMMC_BOOT1: 0x0000400000 (4,00Mb)
EMMC_BOOT2: 0x0000400000 (4,00Mb)
EMMC_RPMB : 0x0000400000 (4,00Mb)
EMMC_USER : 0x1D20500000 (116,50Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448,00Kb)
EXT_RAM : 0x0100000000 (4,00Gb)
Get scatter info... OK
Checking USB status... USB_HIGH_SPEED
[EFUSE INFO]: BROM not disabled
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EXT4] ...
Exception: Access violation at address 01266092 in module PandoraTool.exe. Read of address 0E1F6B18

 

[imran999]

link
166.72 MB file on MEGA

 

[GsmToto]

Selected model: Blackview A53 Pro
Operation: Erase FRP
Software version: 7.5

Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM2 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [00000000]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x3B645C9A, 0xDE47C703, 0x53118A37, 0xD12E508A
Get Chip ID... [MT6765]
Get SOC ID... [A6907A2E9248D078F2953B84952FCE345B7K9P3SC7EF0984D699ADB 54790661CEABG3DV]
Get sec config... OK [00000000]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x150100524331344D421296119598C4F7M
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: RC14MB
EMMC_ID : 0x150100524331344D4212961195984F7M
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EXT4] ... OK
Product Brand : Blackview
Product Manufacturer : Blackview
Product Model : A53 Pro
Product Name : A53_Pro
Product Device : A53_Pro
Product Board : k65v1_64_bsp
Board Platform : mt6765
Build ID : A53Pro_NEU_M659_V1.0_20230307V02
Build Date : Tue Mar 7 11:34:05 CST 2023
Display ID : A53Pro_NEU_M659_V1.0_20230307V02
Security Patch : 2023-02-05
Version SDK : 31
Version Release : 12
Version Codename : REL
Firmware Version : 1rck61v164bspP31
Userdata FS Type : EXT4
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Blackview_A53%20Pro/FRP_BACKUP_(2024-9-25_7-11-54)/
Format FRP... [P1] OK
Writting FRP data... OK
Erase FRP done!

 

[GsmToto]

Selected model: Samsung SM-A226B (Samsung Galaxy A22 5G)
Operation: Erase FRP
Software version: 7.5

Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM (Android),usb2ser.sys,3.0.1504.0]
Device found at COM2 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Read Efuse error
Force switch to BROM... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM3 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM3 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xA15CC684, 0x22E887C8, 0xF07D27A9, 0x5BF79B1C
Get Chip ID... [MT6833]
Get SOC ID... [AEEDFB6E1E2AD831EC6DD9755BN5S7X31A3152BC27FD0CB3078F 07A098D1E1CE5M]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x150100444836444142003FB790FAC33M
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: DH6DAB
EMMC_ID : 0x150100444836444142003FB790FAC33M
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 30% - 40% device life time used
DeviceLifeTimeEstB: 30% - 40% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : samsung
Product Manufacturer : samsung
Product Model : SM-A226B
Product Name : a22xnsxx
Product Device : a22x
Product Board : a22x
Board Platform : mt6833
Build ID : SP1A.210812.016
Build Date : Fri Aug 9 19:08:54 +07 2024
Display ID : TP1A.220624.014.A226BXXSADXH7
Security Patch : 2024-08-01
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : A226BXXSADXH1
Userdata FS Type : F2FS
Read partition "frp"... OK
Read partition "persistent"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Samsung_SM-A226B%20(Samsung%20Galaxy%20A22%205G)/FRP_BACKUP_(2024-9-25_18-33-54)/
Format FRP... [P1] [P2] OK
Writting FRP data... OK
Erase FRP done!

 

[erdbets]

is a 2-day rental for sale?

 

[GsmToto]

Selected model: Meizu Y685C (Meizu M3s/M3s Mini)
Operation: Repair
Software version: 7.5
Work ID: 44579005

Connect phone in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM2 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0326
Get sec config... OK [00000007]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CB00, SW VER: 0001, HW SUB CODE: 8A00
Detect chip [MT6755]
Install LibUSB... OK
Waiting for device... OK
Open port... OK
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM2 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0326
Get sec config... OK [00000000]
Get HW & SW version from device... OK
HW VER: CB00, SW VER: 0001, HW SUB CODE: 8A00
Detect chip [MT6755]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x9F4FD7BF, 0x0FAF99AA, 0x3A0BCDMM, 0xBBB03E22
Get Chip ID... [MT6750]
Get sec config... OK [00000000]
Modem count: 6
Load DownloadAgent... OK
Search DA... OK [2]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x70010045484143454101220B33455M
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: EHACEA
EMMC_ID : 0x7001004548414345410122033456M
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x0390000000 (14.25Gb)
RAM INFO:
INT_SRAM: 0x0000038000 (224.00Kb)
EXT_RAM : 0x0080000000 (2.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 40% - 50% device life time used
DeviceLifeTimeEstB: 40% - 50% device life time used
Checking USB status... USB_FULL_SPEED
Switching to USB high speed... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek DA USB VCOM (Android),usb2ser.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
High Speed USB detected at COM14
Open port... OK
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : Meizu
Product Manufacturer : Meizu
Product Model : M3s
Product Name : M3s
Product Device : M3s
Product Board : M3s
Board Platform : mt6750
Build ID : LMY47I
Build Date : Fri Dec 22 10:03:49 CST 2017
Display ID : Flyme 6.2.0.0G
Security Patch : 2017-04-05
Version SDK : 22
Version Release : 5.1
Version Codename : REL
Firmware Version : 15139082234
Read security partition from phone...
Decrypting security data... OK
Encrypt security data... OK
Read partition "nvdata"... OK
Read partition "protect1"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read security files... OK
Calculating... OK
Read IMEI... OK
IMEI 1: 357805899707870
IMEI 2:
Repairing IMEI...
IMEI 1: 35725705411768
IMEI 2: 35736789954336
Write IMEI [NVDATA]... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Repair Security done!

 

[GsmToto]

Selected model: Xiaomi Redmi A3 (Blue)
Operation: Erase FRP And Wipe
Software version: 7.5
Erasing of partitions can damage your device.
Make sure that you have a backup created. Continue? YES

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX or PC] in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM (Android),usb2ser.sys,3.0.1504.0]
Device found at COM3 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [00000007]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0xAEBC6951, 0x8BF3306D, 0x64643568, 0x3F3E23RH
Load DownloadAgent... OK
Search DA... OK [0]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [PRELOADER]
Preloader alive. Skip initializing external RAM
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: C09E00
EMMC_ID : 0xD62D0043303945303051179CDF30SSFG
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x0E92EC0000 (58.30Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x00C0000000 (3.00Gb)
Checking USB status... USB_HIGH_SPEED
[EFUSE INFO]: BROM disabled !!!
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : blue
Product Name : blue_global
Product Device : blue
Product Board : blue
Board Platform : mt6765
Build ID : SP1A.210812.016
Build Date : Sun May 26 19:01:13 CST 2024
Display ID : 14 V816.0.6.0.UGRMISC
Security Patch : 2024-05-01
Version SDK : 34
Version Release : 14
Version Codename : REL
Firmware Version : V816.0.6.0.UGRMIDV
Userdata FS Type : F2FS
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Xiaomi_Redmi%20A3%20(Blue)/FRP_BACKUP_(2024-9-26_7-55-21)/
Format FRP... [P1] OK
Formatting "userdata" partition... OK
Formatting "metadata" partition... OK
Formatting "md_udc" partition... OK
Wipe data done!

 

[GsmToto]

Selected model: Lenovo Qualcomm
Operation: Erase FRP
Software version: 7.5

Waiting for device... OK
Device found at COM2
Port: Qualcomm HS-USB QDLoader 9008
Open port... OK
Reading device info... OK
Serial Number: 2849954566
Sahara ver: 2
OEM PK HASH: 503B44F78C1E5374550C1DC0C03F33AF364C42CC50D5972047 DB276871F5BD33
CPU: SM6115 (Snapdragon 662)
Vendor: Qualcomm
MSM HW ID: 0014D0E100000000
SBL SW Ver: 00000000
Prepare custom loader file... OK
Loader hash: 2C7991219190E383864MT103A8E5A93C344081BZE
Loader PK hash: 503B13F78C1E0F364C42CC50D580866MBH7OKFTYH
DB276871F5BD76CA259CEYB60499E73523583A081570M
Loader version: 6.5
Sending loader... OK
FireHose initialization... OK
Detecting memory type... OK [UFS]
Get storage info... OK
Storage info:
Type: UFS
Name: KM5V8001DM-B622
Page size: 1000
Block size: 1000
Partition count: 6
LU0 size: 0x1CB9800000
LU1 size: 0x0000800000
LU2 size: 0x0000800000
LU3 size: 0x0008000000
LU4 size: 0x0100000000
LU5 size: 0x0008000000
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... OK
Product Brand : qti
Product Manufacturer : QUALCOMM
Product Model : qssi system image for arm64
Product Device : qssi
Product Board : bengal
Board Platform : bengal
Build ID : RKQ1.210303.002
Build Date : Thu Mar 2 02:01:19 CST 2023
Display ID : TB-J606F_S320273_230302_ROW
Security Patch : 2023-02-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : TB-J606F_USR_S320273_2303020027_Q00070_ROW
Userdata FS Type : F2FS
Erase FRP... OK
Done!

 

[yousafawan]

please add emmc health report in edl mode, as cheked in easy jtag plus edl mode.