Hi Z3x team. I swear to God please reply. What is meaning of this error?
Cant repartition it. please understand its very important for me
Sanitize ok. write config ok.
Operation: Connect to Z3X EasyJtagPlus (2023)
Setting Interface to EasyJtag2/UFS-Socket
Setting IO Levels to Low
Setting Frequence to 66 Mhz
Socket Information :
Socket Mark: EasyJTAG UFS Socket BGA-153 by EasyJTAG 25.12.23
Socket Serial:**
Socket Type: UFS_SOCKET_BGA_153
UFS Power Information :
Mode: Low, VCC: 3221 mV, VCCQ2: 1877 mV
UFS Device Information :
UFS Manufacturer: SAMSUNG, UFS ProductName: KLUEG8UHDC-B0E1
UFS Version: 3.1, UFS OemID: SAMSUNG_OEM_ID, UFS FirmVersion: 2.00, UFS SerialNumber: 5349a565961e
Maximum Number of LUs: 8, Number of LUs found: 6, Number of WLUs found: 1, LUs Re-configure: Enabled
RPMB Counter: 111651
UFS LUN 0 Capacity: 63800 MB (000F93800000)
UFS LUN 1 (Main Boot A) Capacity: 8 MB (000000800000)
UFS LUN 2 (Boot B) Capacity: 8 MB (000000800000)
UFS LUN 3 Capacity: 32 MB (000002000000)
UFS LUN 4 Capacity: 1024 MB (000040000000)
UFS LUN 5 Capacity: 160 MB (00000A000000)
Device Life Time Estimation B: 0x01 0% - 10% device life time used
Device Life Time Estimation A: 0x01 0% - 10% device life time used
Pre EOL information: 0x01 Normal (Consumed less then 80% of reserved block)
Backup saved: UFS_SAMSUNG_KLUEG8UHDC-B0E1_5349a565961e_20240219_093216_config.ini (new backup)
Do not turn the socket before you press "Close Session" button
Connected successfully
Operation: Scan PartitionTable from Source (Vendor: Binary Read/Write)
Scanning soft partitions from LUN 0
GPT header is not found
Scanning soft partitions from LUN 1 (Main Boot A)
GPT header is not found
Scanning soft partitions from LUN 2 (Boot B)
GPT header is not found
Scanning soft partitions from LUN 3
GPT header is not found
Scanning soft partitions from LUN 4
GPT header is not found
Scanning soft partitions from LUN 5
GPT header is not found
Operation: Opening Firmware (Qualcomm)
Firmware: C:\Users\FARAH\Desktop\gsmxt.com_Poco X3 Pro (vayu) Eng Firmware\images\
Rom: LUN 0, File: rawprogram0.xml
LUN 0: The size of the "USERDATA" partition has been increased
Rom: LUN 1 (Main Boot A), File: rawprogram1.xml
LUN 1 (Main Boot A): The size of the "LAST_PARTI" partition has been increased
Rom: LUN 2 (Boot B), File: rawprogram2.xml
LUN 2 (Boot B): The size of the "LAST_PARTI" partition has been increased
Rom: LUN 3, File: rawprogram3.xml
LUN 3: The size of the "LAST_PARTI" partition has been increased
Rom: LUN 4, File: rawprogram4.xml
LUN 4: The size of the "LAST_PARTI" partition has been increased
Rom: LUN 5, File: rawprogram5.xml
LUN 5: The size of the "LAST_PARTI" partition has been increased
If the "rawprogram" files are selected incorrectly - you can select them manually
Double-click on ROM file, change the file type to "Firmware files" and select the correct rawprogram
Opening firmware completed
Operation: Writing by Vendor (Qualcomm)
Write/Erase check: Disabled
BlockSize: Auto
Repartitioning ...
Rom: LUN 0, Part: PrimaryGPT, Address: 000000000000, Filename: gpt_main0.bin
Error writing at address: 000000000000 , error: -403, UAP SCSI: Command sense: MEDIUM_ERROR ... Retry #1
Error writing at address: 000000000000 , error: -403, UAP SCSI: Command sense: MEDIUM_ERROR ... Retry #2
Error writing at address: 000000000000 , error: -403, UAP SCSI: Command sense: MEDIUM_ERROR ... Retry #3
Repartition failed. Operation canceled
Cant repartition it. please understand its very important for me
Sanitize ok. write config ok.
Operation: Connect to Z3X EasyJtagPlus (2023)
Setting Interface to EasyJtag2/UFS-Socket
Setting IO Levels to Low
Setting Frequence to 66 Mhz
Socket Information :
Socket Mark: EasyJTAG UFS Socket BGA-153 by EasyJTAG 25.12.23
Socket Serial:**
Socket Type: UFS_SOCKET_BGA_153
UFS Power Information :
Mode: Low, VCC: 3221 mV, VCCQ2: 1877 mV
UFS Device Information :
UFS Manufacturer: SAMSUNG, UFS ProductName: KLUEG8UHDC-B0E1
UFS Version: 3.1, UFS OemID: SAMSUNG_OEM_ID, UFS FirmVersion: 2.00, UFS SerialNumber: 5349a565961e
Maximum Number of LUs: 8, Number of LUs found: 6, Number of WLUs found: 1, LUs Re-configure: Enabled
RPMB Counter: 111651
UFS LUN 0 Capacity: 63800 MB (000F93800000)
UFS LUN 1 (Main Boot A) Capacity: 8 MB (000000800000)
UFS LUN 2 (Boot B) Capacity: 8 MB (000000800000)
UFS LUN 3 Capacity: 32 MB (000002000000)
UFS LUN 4 Capacity: 1024 MB (000040000000)
UFS LUN 5 Capacity: 160 MB (00000A000000)
Device Life Time Estimation B: 0x01 0% - 10% device life time used
Device Life Time Estimation A: 0x01 0% - 10% device life time used
Pre EOL information: 0x01 Normal (Consumed less then 80% of reserved block)
Backup saved: UFS_SAMSUNG_KLUEG8UHDC-B0E1_5349a565961e_20240219_093216_config.ini (new backup)
Do not turn the socket before you press "Close Session" button
Connected successfully
Operation: Scan PartitionTable from Source (Vendor: Binary Read/Write)
Scanning soft partitions from LUN 0
GPT header is not found
Scanning soft partitions from LUN 1 (Main Boot A)
GPT header is not found
Scanning soft partitions from LUN 2 (Boot B)
GPT header is not found
Scanning soft partitions from LUN 3
GPT header is not found
Scanning soft partitions from LUN 4
GPT header is not found
Scanning soft partitions from LUN 5
GPT header is not found
Operation: Opening Firmware (Qualcomm)
Firmware: C:\Users\FARAH\Desktop\gsmxt.com_Poco X3 Pro (vayu) Eng Firmware\images\
Rom: LUN 0, File: rawprogram0.xml
LUN 0: The size of the "USERDATA" partition has been increased
Rom: LUN 1 (Main Boot A), File: rawprogram1.xml
LUN 1 (Main Boot A): The size of the "LAST_PARTI" partition has been increased
Rom: LUN 2 (Boot B), File: rawprogram2.xml
LUN 2 (Boot B): The size of the "LAST_PARTI" partition has been increased
Rom: LUN 3, File: rawprogram3.xml
LUN 3: The size of the "LAST_PARTI" partition has been increased
Rom: LUN 4, File: rawprogram4.xml
LUN 4: The size of the "LAST_PARTI" partition has been increased
Rom: LUN 5, File: rawprogram5.xml
LUN 5: The size of the "LAST_PARTI" partition has been increased
If the "rawprogram" files are selected incorrectly - you can select them manually
Double-click on ROM file, change the file type to "Firmware files" and select the correct rawprogram
Opening firmware completed
Operation: Writing by Vendor (Qualcomm)
Write/Erase check: Disabled
BlockSize: Auto
Repartitioning ...
Rom: LUN 0, Part: PrimaryGPT, Address: 000000000000, Filename: gpt_main0.bin
Error writing at address: 000000000000 , error: -403, UAP SCSI: Command sense: MEDIUM_ERROR ... Retry #1
Error writing at address: 000000000000 , error: -403, UAP SCSI: Command sense: MEDIUM_ERROR ... Retry #2
Error writing at address: 000000000000 , error: -403, UAP SCSI: Command sense: MEDIUM_ERROR ... Retry #3
Repartition failed. Operation canceled