Post Here Sucessfully Unlocked/Repair Phones With Umt Tool

[GsmToto]

Poco X3 Pro (vayu) frp reset done

Operation : Reset FRP (Sideload)
Searching for phone in sideload mode...Found
Device Id : vayu
Version : V13.0.3.0.SJUMIXM
Code Base : 12
Serial : 0xd337b5ec
Ext Info : MK, mk, F, 2, 2
Model : vayu_global
Reading Partition Table...[106] OK
Resetting FRP...Done
Operation Finished.
QcFire Ver. 9.2

 

[GsmToto]

SELECTED: Tiger T606
ACTION: Erase FRP
Start Detect phone...
Phone must be off with battery inside.
Long press "VOL -" key and insert usb cable.
For some phones need to
Long press "VOL -"+ "VOL +" key and insert usb cable.
Detected: SPRD U2S Diag (COM11)
Sending payload, keep boot key untill loader start.
Exploiting phone.....
Sending preloader 1
Sending preloader 2
Sending FDL 1.....
Sending FDL 2.....
New flash metod detected.
UID: 00742943041b8583
FileSystem: EMMC
Read partition info is supported by loader.
CPU NAME: T606
Removing frp, wait...
[1]FRP: persist
Format OK.
[can take 0-10 sec]Wait untill phone restart.

 

[GsmToto]

Operation : Multi Flash
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM124)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.3.5
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1A01000 [SDM665] 00007200
OPK_DATA : 4B60244704D721E5B96DD5BB7233886E38F2198FBDE6433FCE 1D25A7B0472DD7
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [SDM665]...Done
Executing Loader...OK
Detecting Storage Type...OK
Hardware : SDM665, EMMC, 64 GB
LU Count : 4 [0x0747C000] [0x00002000] [0x00002000] [0x00008000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [65536], Out: 16384, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi
Software : , V12.5.2.0.RCOMIXM [Wed Feb 16 22:04:28 WIB 2022]
Android Ver. : 11
Patch Level : 2022-02-01
Processing [rawprogram0.xml]
Writing [qupv3fw.elf] -> [qupfw] ...Done
Writing [qupv3fw.elf] -> [qupfwbak] ...Done
Writing [vbmeta.img] -> [vbmeta] ...Done
Writing [vbmeta.img] -> [vbmetabak] ...Done
Writing [xbl_config.elf] -> [xbl_config] ...Done
Writing [xbl_config.elf] -> [xbl_configbak] ...Done
Writing [devcfg.mbn] -> [devcfg] ...Done
Writing [devcfg.mbn] -> [devcfgbak] ...Done
Writing [storsec.mbn] -> [storsec] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [rpm.mbn] -> [rpmbak] ...Done
Writing [hyp.mbn] -> [hyp] ...Done
Writing [hyp.mbn] -> [hypbak] ...Done
Writing [km4.mbn] -> [keymaster] ...Done
Writing [km4.mbn] -> [keymasterbak] ...Done
Writing [cmnlib.mbn] -> [cmnlib] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64] ...Done
Writing [cmnlib.mbn] -> [cmnlibbak] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64bak] ...Done
Writing [abl.elf] -> [abl] ...Done
Writing [abl.elf] -> [ablbak] ...Done
Writing [BTFM.bin] -> [bluetooth] ...Done
Writing [BTFM.bin] -> [bluetoothbak] ...Done
Writing [misc.img] -> [misc] ...Done
Writing [imagefv.elf] -> [imagefv] ...Done
Writing [imagefv.elf] -> [imagefvbak] ...Done
Writing [uefi_sec.mbn] -> [uefisecapp] ...Done
Writing [uefi_sec.mbn] -> [uefisecappbak] ...Done
Writing [xbl.elf] -> [xbl] ...Done
Writing [xbl.elf] -> [xblbak] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [tz.mbn] -> [tzbak] ...Done
Writing [logfs_ufs_8mb.bin] -> [logfs] ...Done
Writing [metadata.img ] -> [metadata]...Done
Writing [dtbo.img] -> [dtbo] ...Done
Writing [dtbo.img] -> [dtbobak] ...Done
Writing [dspso.bin] -> [dsp] ...Done
Writing [dspso.bin] -> [dspbak] ...Done
Writing [persist.img] -> [persist] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [boot.img] -> [bootbak] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [NON-HLOS.bin] -> [modembak] ...Done
Writing [cust.img ] -> [cust]...Done
Writing [vendor.img ] -> [vendor]...Done
Writing [system.img ] -> [system]...Done
Writing [userdata.img ] -> [userdata]...Done
Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done
Writing [gpt_backup0.bin] -> [BackupGPT] ...Done
Applying Patches................Done
Set Boottable Storage Drive to 0...Done
Reading Partition Table...OK
Resetting FRP Lock.......Done
Resetting device...Done
Operation Finished.
QcFire Ver. 9.2

 

[GsmToto]

Operation : Reset Mi Account (New)
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
SAMSUNG : Turn Off phone, hold EDL Cable Button and insert to phone and
press VOL DOWN + POWER on phone more than 3 times rapidly and then leave EDL Cable Button.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM35)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.3.5
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1F00B00 [8937] 00007200
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD37993 0D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8937_035]...Done
Executing Loader...OK
Auth Enabled Device! You may need Mi Auth Account to service!
Skipping Auth...OK
Detecting Storage Type...OK
Hardware : 8937, EMMC, 16 GB
LU Count : 3 [0x01D5A000] [0x00002000] [0x00002000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi Redmi 7A [pine]
Brand : Xiaomi
Prod.Name : pine
Software : ZQL1533-pine-build-20200407194230, V11.0.7.0.PCMMIXM [Tue Apr 7 19:44:29 WIB 2020]
Android Ver. : 9
Patch Level : 2020-03-01
Reading Data[1]...Done
Patching Data...Done
Writing Data...Done
Reading Data[2]...Done
Patching Data...Done
Account : 6544466685
Phone : +53544444444
Display ID : 44Y6-AHCO-ZTKZ-LAY
Writing Data...Done
Operation Finished.
QcFire Ver. 9.2

 

[GsmToto]

Operation : Remove Huawei ID (Automatic Reest)
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM5)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1801B00 [SM6225] 6D001500
OPK_DATA : E2D62B196391DF63693F01E753DC831C3A831CF3CA9D702A1C2EB2F1374208B2
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [SM6225]...Done
Executing Loader...OK
Detecting Storage Type...OK
Hardware : SM6225, UFS, 128 GB
LU Count : 6 [0x01D7E800] [0x00000800] [0x00000800] [0x00002000] [0x00047000] [0x00002000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [65536], Out: 16384, Sector Size: 4096
Reading Partition Table...OK
Reading Device Information...OK [Sign]
Build :
Int. Build :
Reading Backup...
Backup : Huawei_Id_Backup_SM6225_240109_193605.bak
If device stuck in boot loop, restore this backup.
Resetting Huawei ID...Done
Operation Finished.
QcFire Ver. 9.2

 

[GsmToto]

Realme RMX2361 C21Y Flashing Success Stock PAC Firmware via Unisoc UMT..

Firmware Ver: RMX3261_11_A.101_20230208211542

ACTION: Flash Firmware.
Selected firmware: S19610AA1_ctcc-user-native_SHARKL5PRO_SUPER_R.pac
NV: Skip write nvram
Device Storage: EMMC
Start Detect phone...
Phone must be off with battery inside.
Long press "VOL -" key and insert usb cable.
For some phones need to
Long press "VOL -"+ "VOL +" key and insert usb cable.
Detected: SPRD U2S Diag (COM7)
[00:00:00] Sending loader.
BOOT: SPRD3
Sending loader, keep boot key untill loader start.
[00:00:04] Loader ok
[00:00:05] Wait for loader....
Loader send OK
Changing bautrate OK.
[00:00:05] [1]First boot done.
[00:00:05] Sending second loader.
[00:00:15] Second loader sent ok.
New flash protocol detected.
[00:00:15] Reading: miscdata
[00:00:16] Reading: l_fixnv1_a
NVRAM saved to: C:\UMT\unisoc_module\spreadtrum_module_backup_fold er\flashmode_nvram_backup\_867400020316612\_867400 020316612_nvram_backup.tar
Phone have super partition.
[00:00:27] Making flash ic repartition.
[00:00:27] Format: splloader
[00:00:27] [splloader]Format OK.
[00:00:27] Start write: prodnv
[00:00:27] Format: uboot_log
[00:00:27] [uboot_log]Format OK.
[00:00:27] Start write: vbmeta_a
[00:00:27] Start write: vbmeta_system_a
[00:00:27] Start write: vbmeta_system_ext_a
[00:00:27] Start write: vbmeta_vendor_a
[00:00:28] Start write: vbmeta_product_a
[00:00:28] Start write: l_modem_a
[00:00:30] Start write: l_deltanv_a
[00:00:30] Start write: l_ldsp_a
[00:00:32] Start write: l_gdsp_a
[00:00:33] Start write: l_agdsp_a
[00:00:34] Start write: pm_sys_a
[00:00:35] Start write: gnssmodem_a
[00:00:35] Start write: wcnmodem_a
[00:00:35] Start write: boot_a
[00:00:40] Start write: dtbo_a
[00:00:41] Start write: super
[00:11:32] Start write: cache
[00:11:32] Start write: my_preload
[00:13:12] Start write: userdata
[00:13:38] Start write: logo
[00:13:38] Start write: fbootlogo
[00:13:38] Start write: socko_a
[00:13:43] Start write: odmko_a
[00:13:43] Format: l_runtimenv1
[00:13:43] [l_runtimenv1]Format OK.
[00:13:43] Format: misc
[00:13:43] [misc]Format OK.
[00:13:43] Format: sysdumpdb
[00:13:43] [sysdumpdb]Format OK.
[00:13:43] Start write: trustos_a
[00:13:43] Start write: teecfg_a
[00:13:43] Start write: sml_a
[00:13:44] Start write: uboot_a
[00:13:44] Start write: persist
[00:13:44] Format: metadata
[00:13:44] [metadata]Format OK.
[00:13:44] Start write: splloader
Flashing done.
If phone stuck on logo long time perform wipe from recovery or safe reset from exe
[can take 0-10 sec]Wait untill phone restart.
Log saved:
C:\UMT\unisoc_module\spreadtrum_module_backup_fold er\Saved_Logs\_writepac_.txt
Total Time: 00:18:31
Done.

 

[GsmToto]

Device : Samsung Galaxy A23 (SM-A235F)
Operation : Reset FRP
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM11)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1801B00 [SM6225] 00002000
OPK_DATA : 9C04D328444AFF080141EBDAC3941A2CF3BC4FF1A6423E0201F7CE5510B8A3
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [SM6225_005]...Done
Executing Loader...OK
Detecting Storage Type...OK
Hardware : SM6225, UFS, 128 GB
LU Count : 6 [0x01DA8C00] [0x00000800] [0x00000800] [0x00000400] [0x00020000] [0x00000800]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [65536], Out: 16384, Sector Size: 4096
Reading Partition Table...OK
Reading Device Information...OK [Sign]
Build : A235FXXU1BVK8
Int. Build : SM-A235F_CIS_SER_QKEY0
Resetting FRP Lock...Done
Using Patch Method... Done Done
Operation Finished.
QcFire Ver. 9.2

 

[GsmToto]

---

Job: Remove FRP
SELECTED: C35
ACTION: Erase FRP
Start Detect phone...
Phone must be off with battery inside.
Long press "VOL -" key and insert usb cable.
For some phones need to
Long press "VOL -"+ "VOL +" key and insert usb cable.
Detected: SPRD U2S Diag (COM7)
Sending payload, keep boot key untill loader start.
Exploiting phone.....
Sending preloader 1
Sending preloader 2
Sending FDL 1.....
Sending FDL 2.....
New flash metod detected.
UID: 007418c00c0b0c29
FileSystem: UFS
Read partition info is supported by loader.
***************
Manufacturer: realme
Brand: realme
Device: RE87BAL1
Model: RMX3511
Build ID: SP1A.210812.016
CPU arhitecture: arm64-v8a
Build product name: ums9230_nico
Build description: ums9230_nico_Natv-user 12 SP1A.210812.016 2627 release-keys
Build Id: SP1A.210812.016
Android Release: 12
Android Version: RMX3511PU_12_C.33
Security patch: 2023-09-05
CPU NAME: T616
Removing frp, wait...
[1]FRP: persist
Format OK.
[can take 0-10 sec]Wait untill phone restart.

 

[GsmToto]

Samsung SM-A207F Done By UMT

Operation : Samsung Reset FRP
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM9)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Opening Port...OK
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
SAMSUNG : Turn Off phone, hold EDL Cable Button and insert to phone and
press VOL DOWN + POWER on phone more than 3 times rapidly and then leave EDL Cable Button.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM9)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1A00900 [8953] 00002000
OPK_DATA : 2444EA6A40A4CCA1CF7FCDBD41E29AB36E1AA41A820424ADA3 B1DA7DA21379DA
Initializing Protocol...OK
Using Auto Loader Selection [3]
Device may possibly not boot with this loader.
Preparing Loader...Done
Sending Loader [8953_036]...Write Error!
Please use correct loader and check USB port / cable.
Operation Finished.
QcFire Ver. 9.2

 

[GsmToto]

Operation : Reset FRP
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
SAMSUNG : Turn Off phone, hold EDL Cable Button and insert to phone and
press VOL DOWN + POWER on phone more than 3 times rapidly and then leave EDL Cable Button.
Found Port
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.7
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1F00B00 [8937] 00002000
OPK_DATA : 6C429E6D6583C49ADCAF169BD1A23255CCED44DF35B7F8A7A4F9795AED7AF713
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8937_044]...Done
Executing Loader...OK
Detecting Storage Type...OK
Hardware : 8937, EMMC, 16 GB
LU Count : 3 [0x01D5A000] [0x00002000] [0x00002000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Software : SP1A.210812.016.A015FXXU5CVK5, A015FXXU5CVK5 [Mon Nov 14 14:16:23 KST 2022]
Android Ver. : 12
Patch Level : 2022-09-01
Resetting FRP Lock......Done
Operation Finished.
QcFire Ver. 9.2

 

[GsmToto]

Device : Samsung Galaxy S21 Ultra 5G (SM-G998U) U5
Operation : Samsung Lost Mode Reset
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM5)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.5.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1501300 [SM8350] 00002000
OPK_DATA : 07A9DD9638DAB4DEF8D9C2C7B875AA3F8F0C6106739DF45B69 CDA916BADE9D43
Initializing Protocol...OK
Using Pre-Defined Loader [SMG998U_U5.ufl]
Preparing Loader...Done
Sending Loader [SMG998U_U5]...Done
Executing Loader...OK
Detecting Storage Type...OK
Hardware : SM8350, UFS, 256 GB
LU Count : 6 [0x03B73C00] [0x00000800] [0x00000800] [0x00000400] [0x00020000] [0x00000800]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [65536], Out: 16384, Sector Size: 4096
Reading Partition Table...OK
Reading Device Information...OK
Software : TP1A.220624.014.G998USQU5DWA8, G998USQU5DWA8 [Tue Jan 10 21:22:40 KST 2023]
Android Ver. : 13
Patch Level : 2023-01-01
Resetting Lost Mode... Done Done Done
Once phone reboot in Odin Mode, full flash your device.
If stuck on Charging Logo, hold VOL DOWN + PWR for 7 Seconds.
Operation Finished.
QcFire Ver. 9.2

 

[GsmToto]

Device : Samsung Galaxy S23 Plus 5G (SM-S916B) U3
Operation : Samsung Reset FRP
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM5)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.3.7
Opening Port...OK
Init Handshake Sequence...Done
Protocol v3 or higher detected. Auto Loader unsupported.
Initializing Protocol...OK
Using Pre-Defined Loader [SMS916B_U3.ufl]
Preparing Loader...Done
Sending Loader [SMS916B_U3]...Done
Executing Loader...OK
Detecting Storage Type...OK
Hardware : , UFS, 256 GB
LU Count : 6 [0x03B64000] [0x00001400] [0x00001400] [0x00002000] [0x00028000] [0x00002000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [65536], Out: 16384, Sector Size: 4096
Reading Partition Table...OK
Reading Device Information...OK [Sign]
Build : S916BXXS3BWDG
Int. Build : SM-S916B_EUR_XX_QKSR5
Reset FRP... Done
Operation Finished.
QcFire Ver. 9.2

 

[GsmToto]

Device : Samsung SM-M015F/DS
Operation : Reset FRP
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
SAMSUNG : Turn Off phone, hold EDL Cable Button and insert to phone and
press VOL DOWN + POWER on phone more than 3 times rapidly and then leave EDL Cable Button.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM8)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.7
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1F00B00 [8937] 00002000
OPK_DATA : B0F75607F03929422ADA159518DA3EC476DA7DE8F7953B6BA6 7BAF9610DF27F8
Initializing Protocol...OK
Using Auto Loader Selection [3]
Device may possibly not boot with this loader.
Preparing Loader...Done
Sending Loader [8937_044]...Write Error!
Please use correct loader and check USB port / cable.
Operation Finished.
QcFire Ver. 9.2

 

[GsmToto]

job: Remove FRP
SELECTED: SC9863A_64
ACTION: Erase FRP
Start Detect phone.
Phone must be off(you can service this phone without battery also).
Long press "VOL -"+ "VOL +" key while inserting usb cable.
Keep key untill boot complete.
Detected: SPRD U2S Diag (COM8)
Sending payload, keep boot key untill loader start.
Exploiting phone.....
Sending preloader 1
Sending preloader 2
Sending FDL 1.....
Sending FDL 2.....
New flash metod detected.
FileSystem: EMMC
Read partition info is supported by loader.
CPU NAME: SC9863A
Removing frp, wait...
[1]FRP: persist
Format OK.
[can take 0-10 sec]Wait untill phone restart.
Log saved:
C:\UMT\unisoc_module\spreadtrum_module_backup_fold er\Saved_Logs\_erase_frp_15.txt
Total Time: 00:00:28
Done.

 

[GsmToto]

Job: Remove FRP
SELECTED: Tiger T606
ACTION: Erase FRP
Start Detect phone...
Phone must be off with battery inside.
Long press "VOL -" key and insert usb cable.
For some phones need to
Long press "VOL -"+ "VOL +" key and insert usb cable.
Detected: SPRD U2S Diag (COM8)
Sending payload, keep boot key untill loader start.
Exploiting phone.....
Sending preloader 1
Sending preloader 2
Sending FDL 1.....
Sending FDL 2.....
New flash metod detected.
UID: 00742483003a8b8f
FileSystem: EMMC
Read partition info is supported by loader.
CPU NAME: T606
Removing frp, wait...
[1]FRP: persist
Format OK.
[can take 0-10 sec]Wait untill phone restart.
Log saved:
C:\UMT\unisoc_module\spreadtrum_module_backup_fold er\Saved_Logs\_erase_frp_17.txt
Total Time: 00:00:37
Done

 

[GsmToto]

Job: Boot Info
SELECTED: Tiger T610(UMS512)
[0]ACTION: Boot Info
Start Detect phone...
Phone must be off with battery inside.
Long press "VOL -" key and insert usb cable.
For some phones need to
Long press "VOL -"+ "VOL +" key and insert usb cable.
Detected: SPRD U2S Diag (COM3)
Sending payload, keep boot key untill loader start.
Exploiting phone.....
Sending preloader 1
Sending preloader 2
Sending FDL 1.....
Sending FDL 2.....
New flash metod detected.
FileSystem: EMMC
Read partition info is supported by loader.
***************
Manufacturer: incar
Brand: SGIN
Device: SGIN_X10
Model: SGIN_X10
Build ID: RP1A.201005.001
CPU arhitecture: arm64-v8a
Fota platform: Sprd9863_11.0
Build product name: SGIN_X10_EEA
Build description: SGIN_X10_EEA-user 11 RP1A.201005.001 20211207 release-keys
Build Id: RP1A.201005.001
Android Release: 11
Android Version: SGIN_X10_EEA_20220106
Security patch: 2021-12-05
CPU NAME: T610
SN: Y2210NS01194
Found [l_fixnv1_a] [l_fixnv1_a] Size to download: 2 MB
Reading: l_fixnv1_a size: 2097152
IMEI 1: 352328xxxxxxxxxx
IMEI 2: 86740xxxxxxxxxxx
IMEI 3: 86740xxxxxxxxxxx
IMEI 4: 86740xxxxxxxxxxx
Simlock Type: 4

Simlock Status:
SIMLOCK: INACTIVE
NETWORK SUBNET: INACTIVE
SP LOCK: INACTIVE
CORPORATE: INACTIVE
USER LOCK: INACTIVE
[4]Simlock Type: 0 0
Security saved: C:\UMT\unisoc_module\spreadtrum_module_backup_fold er\flashmode_security_backup\SGIN_SGIN_X10_EEA_202 20106_352328xxxxxxxxxxxx_security_backup.tar
[can take 0-10 sec]Wait untill phone restart.
Log saved:
C:\UMT\unisoc_module\spreadtrum_module_backup_fold er\Saved_Logs\SGIN_SGIN_X10_EEA_20220106_boot_info .txt
Total Time: 00:00:31
Done.

 

[GsmToto]

Job: Boot Info
SELECTED: SC9863A_V2
[0]ACTION: Boot Info
Start Detect phone.
Phone must be off(you can service this phone without battery also).
Long press "VOL -"+ "VOL +" key while inserting usb cable.
Keep key untill boot complete.
Detected: SPRD U2S Diag (COM8)
Sending payload, keep boot key untill loader start.
Exploiting phone.....
Sending preloader 1
Sending preloader 2
Sending FDL 1.....
Sending FDL 2.....
New flash metod detected.
FileSystem: EMMC
Read partition info is supported by loader.
CPU NAME: SC9863A
SN: X5002022HGM18821433
Found [l_fixnv1_a] [l_fixnv1_a] Size to download: 2 MB
Reading: l_fixnv1_a size: 2097152
IMEI 1: 867400020314566
IMEI 2: 867400020312234
IMEI 3: 867400020319808
IMEI 4: 867400020315534
Simlock Type: 4

Simlock Status:
SIMLOCK: INACTIVE
NETWORK SUBNET: INACTIVE
SP LOCK: INACTIVE
CORPORATE: INACTIVE
USER LOCK: INACTIVE
[4]Simlock Type: 0 0
[can take 0-10 sec]Wait untill phone restart.
Log saved:
C:\UMT\unisoc_module\spreadtrum_module_backup_fold er\Saved_Logs\_boot_info_15.txt
Total Time: 00:00:43
Done.


Job: Firmware Backup
SELECTED: SC9863A_V2
ACTION: Backup Firmware
Start Detect phone.
Phone must be off(you can service this phone without battery also).
Long press "VOL -"+ "VOL +" key while inserting usb cable.
Keep key untill boot complete.
Detected: SPRD U2S Diag (COM8)
Sending payload, keep boot key untill loader start.
Exploiting phone.....
Sending preloader 1
Sending preloader 2
Sending FDL 1.....
Sending FDL 2.....
New flash metod detected.
FileSystem: EMMC
Read partition info is supported by loader.
CPU NAME: SC9863A
Backup firmware by loader.
CPU NAME: SC9863A
Found [l_fixnv1_a] [l_fixnv1_a] Size to download: 2 MB
IMEI: 867400020316612
Reading: splloader
[A]Reading: prodnv
[6]Reading: trustos_a
[1]Reading: sml_a
Reading: uboot_a
[6]Reading: logo
[6]Reading: fbootlogo
Reading: l_fixnv1_a
[1]Reading: gpsgl_a
[1]Reading: gpsbd_a
[A]Reading: wcnmodem_a
Reading: persist
[19]Reading: l_modem_a
[1]Reading: l_deltanv_a
[A]Reading: l_gdsp_a
[14]Reading: l_ldsp_a
[1]Reading: pm_sys_a
Reading: teecfg_a
[40]Reading: boot_a
[64]Reading: vendor_boot_a
[8]Reading: dtb_a
[8]Reading: dtbo_a
[15E0]Reading: super
[1]Reading: vbmeta_a
[1]Reading: vbmeta_system_a
[1]Reading: vbmeta_vendor_a
[1]Reading: vbmeta_system_ext_a
[1]Reading: vbmeta_product_a
[can take 0-10 sec]Wait untill phone restart.
Log saved:
C:\UMT\unisoc_module\spreadtrum_module_backup_fold er\Saved_Logs\SC9863A_867408855344_8655773889 22_backup_firmware.txt
Total Time: 00:54:11
Done.

 

[GsmToto]

Operation : Samsung Reset FRP
Checking for existing devices...Found
Port : HS-USB Diagnostics 9008 (COM9)
Driver Info : Mobile, qcusbser.sys, 2.1.2.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1D01400 [SDM662] 00002000
OPK_DATA : C9F0E4B25EEBFDC57496ABA9C04566BED147E0D76DCADA91F4A625B18D3C813
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [SDM662_006]...Done
Executing Loader...OK
Detecting Storage Type...OK
Hardware : SDM662, EMMC, 32 GB
LU Count : 4 [0x03A3E000] [0x00002000] [0x00002000] [0x00008000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [65536], Out: 16384, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Software : RP1A.200720.012.T505NDXU3BVB2, T505NDXU3BVB2 [Wed Feb 16 12:58:56 KST 2022]
Android Ver. : 11
Patch Level : 2022-01-01
Reset FRP... Done
Operation Finished.
QcFire Ver. 9.2

 

[GsmToto]

Device : Samsung Galaxy A01 (SM-A015M-UBU4)
Operation : Reset FRP
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM7)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.3.5
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1F00B00 [8937] 00002000
OPK_DATA : E95B1A9E648A34AA19139A72611C64E3FB16DAF6E6CD981892 6696791FC3D650
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8937_056]...Done
Executing Loader...OK
Detecting Storage Type...OK
Hardware : 8937, EMMC, 32 GB
LU Count : 3 [0x03A3E000] [0x00002000] [0x00002000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Software : SP1A.210812.016.A015MUBS5CWI1, A015MUBS5CWI1 [Sat Sep 2 01:44:17 KST 2023]
Android Ver. : 12
Patch Level : 2023-08-01
Resetting FRP Lock......Done
Operation Finished.
QcFire Ver. 9.2

 

[GsmToto]

ACTION: Flash Firmware.
Selected firmware: X6816C-ST683SBCDS-R-GL-221222V13_GsmMafia.Com.pac
NV: Skip write nvram
Device Storage: EMMC
Start Detect phone...
Phone must be off with battery inside.
Long press "VOL -" key and insert usb cable.
For some phones need to
Long press "VOL -"+ "VOL +" key and insert usb cable.
Detected: SPRD U2S Diag (COM5)
[00:00:00] Sending loader.
BOOT: SPRD3
Sending loader, keep boot key untill loader start.
[00:00:04] Loader ok
[00:00:04] Wait for loader....
Loader send OK
Changing bautrate OK.
[00:00:04] [1]First boot done.
[00:00:04] Sending second loader.
[00:00:13] Second loader sent ok.
New flash protocol detected.
New flash protocol enabling, fail.
Total Time: 00:00:35
Done.