Z3X Pandora Pro 7.10/ 7/.11 Download Release

[GsmToto]

Selected model: Spreadtrum Spreadtrum
Operation: Erase FRP
Software version: 7.10


Connect phone in BROM mode. Use volume key buttons or testpoint.
Waiting for device... OK
Device found at COM5
Port: USB\VID_1782&PID_4D00\6&260A8E58&0&1
Driver: [UNISOC Communications Inc.,sprdvcom,SPRD U2S Diag,sprdvcom.sys,4.19.38.134]
Port type: BROM
Connecting to device... OK
Selected processor: Tiger_T616_64
Load files... (universal) OK
Connect preloader 1... OK
Connect preloader 2... OK
Connect loader 1... OK
Connect loader 2... OK
Serial Number: ZY22-----
Flash Type: UFS
Read partitions info... OK
Checking A/B state... OK [A]
Read product info... [EROFS] ... OK
Product Brand : motorola
Product Manufacturer : motorola
Product Model : moto g14
Product Name : cancun_g
Product Device : cancun
Product Board : cancun
Board Platform : ums9230
Build ID : UTLB34.102-54-1
Build Date : Mon Sep 23 20:48:02 CST 2024
Display ID : UTLB34.102-54-1 release-keys
Security Patch : 2024-10-05
Version SDK : 34
Version Release : 14
Version Codename : REL
Firmware Version : 20f7f152
Userdata FS Type : F2FS
Backup partitions... OK
Formatting "persist" partition... OK
Done!

 

[GsmToto]

Selected model: Nokia TA-1534 (Nokia C32)
Operation: Erase FRP And Wipe
Software version: 7.10

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to NONE... OK
Connect phone to [PC]
Connect phone in BROM mode. Use volume key buttons or testpoint.
Waiting for device... OK
Device found at COM5
Port: USB\VID_1782&PID_4D00\5&28062471&0&3
Driver: [UNISOC Communications Inc.,sprdvcom,SPRD U2S Diag,sprdvcom.sys,4.19.38.134]
Port type: BROM
Connecting to device... OK
Selected processor: SC9863A_69
Load files... (universal) OK
Connect preloader 1... OK
Connect preloader 2... OK
Connect loader 1... OK
Connect loader 2... OK
Serial Number: H3C1421746337696
Read partitions info... OK
Checking A/B state... OK [A]
Read product info... [EROFS] ... OK
Product Brand : Nokia
Product Manufacturer : HMD Global
Product Model : Nokia C32
Product Name : Mockingbird_00WW
Product Device : MKDA
Product Board : s9863a1h66
Board Platform : sp9863a
Build ID : TP1A.220624.014
Build Date : Fri Aug 23 07:20:27 UTC 2024
Display ID : 00WW_1_740_SP01
Security Patch : 2024-09-05
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : 00WW_1_74A
Userdata FS Type : F2FS
Backup partitions... OK
Formatting "persist" partition... OK
Formatting "userdata" partition... OK
Formatting "cache" partition... OK
Formatting "metadata" partition... OK
Creating default filesystems... [CACHE: EXT4] ... [USERDATA: F2FS] ... OK
Done!

 

[vickysah]

- Added support Infinix phones:
Infinix Hot 50 4G X6532, Infinix Xpad X1101, X1101B,
Infinix Note 40S X6850B, Infinix Hot 50 Pro X6881,
Infinix Hot 50 X6882, X6882B, Infinix Zero Flip 5G, X6962,
Infinix Hot 50 Pro Plus X6880, Infinix Note 40 Pro 4G X6850,
Infinix Note 40 X6853, Infinix Zero 40 4G X6860
Infinix Hot 50 5G X6720, X6720B,
Infinix Note 40X 5G X6838, Infinix Note 40 Pro 5G X6851,
Infinix Note 40 Pro Plus 5G X6851B, Infinix Note 40 5G X6852,
Infinix Zero 40 5G X6861, Infinix GT 20 Pro X6871.
- Added support Tecno phones:
CL9 Tecno Camon 30 Premier, CL8 Tecno Camon 30 Pro,
KJ6, KJ6s Tecno Spark 20 Pro, CLA5 Tecno Camon 30S,
KL7 Tecno Spark 30 Pro, T1101 Tecno MegaPad 11,
KJ8 Tecno Spark 20 Pro 5G, KJ7, KJ7s Tecno Spark 20 Pro Plus,
CL6, CL6k, CL6s Tecno Camon 30, CLA6 Tecno Camon 30s Pro,
LI7 Tecno Pova 6, LI6 Tecno Pova 6 Neo,
KL8, KL8s Tecno Spark 30 5G, KL8h Tecno Spark 30C 5G,
CL7, CL7k, CL7s Tecno Camon 30 5G, CK8nB Tecno Camon 20s Pro 5G,
AE11 Tecno Phantom V Flip 2, AE10 Tecno Phantom V Fold 2
KL4hTecno Spark Go 1S, KL5, KL5n, KL5sTecno Spark 30C,
KL6 Tecno Spark 30, T1001 Tecno MegaPad 10.
- Added support Samsung phones:
Galaxy A15 SM-A155F,
Galaxy A05 SM-A055F,
Galaxy A06 SM-A065F/SM-A065M
- Added new loaders for QCOM phones (EDL mode)
- Added new loader for Samsung:
SM-A2070 BIT 5
SM-M236L BIT 9
SM-S928B BIT 4
- Added support for Mediatek based phones:
Alcatel:
6025H, 9309X, 6025A, 5033MP, 8094X, 6002A, 8091, 9317G, 5033FR, 6025D, 6056A,
5033E, 9032X, 5028A, 9013T, 6027A, 5061U, 6056D, 9317X, 6065A, 8094M, 9009F,
9013A, 5007S, 6002D, 5033EP, 5007O, 4063A, 8092, 6056H, 5031D, 5031G, 9317G1,
8052, 5033FP, 5033Q, 6002J, 9032W,
Dexp:
G150, S190, G450 2021, ES1050, G155, MS550, M210
TCL:
T676H, T507J, 6165A, 5164D, T431D, T501C, 9295G, 5044T, 8082, 4058G, 5199I,
5033M, T433D, 5099U, 5058Y, 5058A, 5041C, T431Q, 9460G, 8094M, 5033TP, 8192A,
T431U, 8193A, T771K, T771A, 6062W, 5107G, 5033F, 9080G, 5033E, T767G, T701DL,
T430W, 6127I, 5164A, T431A, T501L, 6165S, 4058W, 6165H, 6127A, T766A, 6102A
FOSSiBOT:
F106 Pro, J12, F105, F101 Pro, DT2, F101, F102, F101 P
LeEco:
Honor 10, Spark 8, LEX620, mate60pro, LEX626, MX710, LEX622, S10, LEX657, LEX653
Orange:
Orange Neva start, Orange Rise32, K2, Orange Nola play, Orange Rise 55
- Added support for Unisoc based phones:
Alcatel:
5030I, 5030J
Dexp:
C37, B31, K11, B18, y400, B38, K21
Orange:
Orange Sanza touch, Orange Nola fun, Orange Nola XL
Download New Software
169.72 MB file on MEGA

 

[GsmToto]

Selected model: Tecno BG7 (Tecno Spark 20C)
Operation: Repair
Software version: 7.10

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX or PC] in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM_V1633 (Android),usb2ser.sys,3.0.1504.0]
Device found at COM2 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0xBAB0E71E, 0xF4CC0383, 0xE801354C, 0x933DA57E
Load DownloadAgent... OK
Search DA... OK [1]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [PRELOADER]
Preloader alive. Skip initializing external RAM
Send 2nd DA... OK
DA2 auth: enabled
Get device info... OK
EMMC INFO:
EMMC_CNAME: A3A562
EMMC_ID : 0xD60103438D0AA91133413536321119BF
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x1CCF000000 (115.23Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0200000000 (8.00Gb)
Checking USB status... USB_HIGH_SPEED
[EFUSE INFO]: BROM not disabled
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EROFS] ... OK
Product Brand : TECNO
Product Manufacturer : TECNO
Product Model : TECNO BG7
Product Name : BG7-OP
Product Device : TECNO-BG7
Product Board : TECNO-BG7
Board Platform : mt6765
Build ID : SP1A.210812.016
Build Date : Fri Jan 19 19:17:42 CST 2024
Display ID : TECNO-T-64-240119V752
Security Patch : 2024-01-05
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : 240119V945
Userdata FS Type : F2FS
Switch to BROM
Read partition "preloader"... OK
Read partition "preloader_backup"... OK
Parse scatter file... OK
Load Rom Images... OK
Erasing preloaders:
Format "preloader" partition... OK
Format "preloader_backup" partition... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to [BOX] in BROM mode
Waiting for device... timeout

 

[GsmToto]

BROM off from preloader
BROM on using TP

Selected model: TMB TMAF025G (TMB Revvl 6)
Operation: Unlock network
Software version: 7.10

Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM5 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM5 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xE9C0EE28, 0x4D945A35, 0x66BD05F3, 0x3DDE35A1
Get Chip ID... [MT6833]
Get SOC ID... [24D31BEE5EE2CA1494CDD85BC5B8576552E4D0640D4DF148564C909B0E183B85]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): eUFS2.2_128 (01.2)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : eUFS2.2_128
UFS_FWVER : 01.2
BLOCK_SIZE: 0x0000001000 (4,00Kb)
UFS_LU0 : 0x0000400000 (4,00Mb)
UFS_LU1 : 0x0000400000 (4,00Mb)
UFS_LU2 : 0x1DD0000000 (119,25Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448,00Kb)
EXT_RAM : 0x0100000000 (4,00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : T-Mobile
Product Manufacturer : Wingtech
Product Model : TMRV065G
Product Name : TorreyPines
Product Device : TorreyPines
Product Board : S98126AA5
Board Platform : mt6833
Build ID : UP1A.235005.007
Build Date : Thu Feb 29 22:13:32 CST 2024
Display ID : TMRV065G_1.15.16
Security Patch : 2024-02-05
Version SDK : 34
Version Release : 14
Version Codename : REL
Firmware Version : SW_S98126AA1_U_V020
Userdata FS Type : F2FS
Read security partition from phone... OK
Read security files... OK
Read NVDATA files... OK
Calculating... OK
Read lock info... OK
Read partition "nvdata"... OK
Read partition "protect1"... OK
Read security files... OK
Read NVDATA files... OK
Read IMEI... OK
Unlock... OK [DF1, DF2, GB1, GB2]
Write lock info... OK
Write security partition to phone... OK
Network Unlock done!

 

[GsmToto]

Selected model: Spreadtrum Spreadtrum
Operation: Erase FRP And Wipe
Software version: 7.10


Connect phone in BROM mode. Use volume key buttons or testpoint.
Waiting for device... OK
Device found at COM3
Port: USB\VID_1782&PID_4D00\5&201B4142&0&10
Driver: [UNISOC Communications Inc.,sprdvcom,SPRD U2S Diag,sprdvcom.sys,4.19.38.134]
Port type: BROM
Connecting to device... OK
Selected processor: Tiger_T700_64
Load files... (universal) OK
Connect preloader 1... OK
Connect preloader 2... OK
Connect loader 1... OK
Connect loader 2... OK
Serial Number: HS61011713001984005A
Read partitions info... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : Symphony
Product Manufacturer : Symphony
Product Model : Z33
Product Name : Z33
Product Device : Z33
Product Board : ums512_1h10
Board Platform : ums512
Build ID : RP1A.201005.001
Build Date : Sat Jan 6 12:23:35 CST 2024
Display ID : Z33_HW3_V21
Security Patch : 2024-01-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 190
Userdata FS Type : F2FS
Backup partitions... OK
Formatting "persist" partition... OK
Formatting "userdata" partition... OK
Formatting "cache" partition... OK
Formatting "metadata" partition... OK
Creating default filesystems... [CACHE: EXT4] ... [USERDATA: F2FS] ... OK
Done!

 

[GsmToto]

Selected model: Xiaomi Mediatek
Operation: Unlock bootloader
Software version: 7.10


Connect phone in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1511.0]
You are using driver version 3.0.1511.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM2 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1511.0]
You are using driver version 3.0.1511.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM2 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x21891BDC, 0xF6226F93, 0x183FCFF8, 0x418A09D8
Get Chip ID... [MT6765]
Get SOC ID... [E17FD82B93320697E16FA1F78A2502710EE81FD0507BEAEE52F62DE830948A2C]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x9B0100591EB980239B9325030333200A
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: Y2P032
EMMC_ID : 0x9B010059980239B9325030333200A1EB
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0747C00000 (29.12Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0080000000 (2.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 10% - 20% device life time used
DeviceLifeTimeEstB: 10% - 20% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : 220233L2C
Product Name : dandelion_cn
Product Device : dandelion
Product Board : dandelion
Board Platform : mt6765
Build ID : RP1A.200720.011
Build Date : Mon Mar 13 19:54:56 CST 2023
Display ID : RP1A.200720.011
Security Patch : 2023-03-01
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : V12.5.13.0.RCZCNXM
Userdata FS Type : F2FS
Read security partition from phone...
Decrypting security data... OK
Encrypt security data... OK
Read security partition from phone... OK
Checking boot unlock status... LOCKED
Downgrading bootloaders for dandelion ... [BL1] ... OK
Write security partition to phone... OK
Unlock bootloader done!

 

[GSM YOUSAF]

keep it up the good work all time my favorite tool

 

[imran999]

we need vivo 2024

 

[Gsmabir]

Please login to view image

Pandora 7.11. Release

Please login to view image

Please login to view image

Fixed bug with flashing Mediatek phones (Signature(Entity) invalid)

Please login to view image

Added support Samsung phones:
- Galaxy F23 SM-E236B (BIT

Please login to view image

- Galaxy M52 5G SM-M526B (BIT 5)
- Galaxy Tab S8 Ultra SM-X900 (BIT 9)
- Galaxy S23 Ultra SCG20 (BIT 1)

Please login to view image

Added new loader for Samsung:
- SM-A025A BIT 8
- SM-A057G BIT 5
- SM-A057M BIT 7
- SM-A235F BIT 9
- SM-A235M BIT 9
- SM-A236B BIT 9
- SM-A236E BIT 9
- SM-A426B BIT 8
- SM-G780G BIT D
- SM-G781B BIT E
- SM-G990B BIT B
- SM-M145F BIT 6
- SM-N986U BIT A
- SM-S908N BIT 6
- SM-S918B BIT 7

Please login to view image

Added support for Mediatek based phones:
- Condor: SP661, PAM524, TB109L, TB108W, TFX714L, Griffe T7, PGN517, Plume L5 Pro, Plume L2 Pro, SP531, SP659, Plume L1, Infinity E5, TFX712G, TB105L, Plume L5, PKT-301, Infinity e5 pro, PGN-404, Plume L3 Smart, Plume L8 Pro, Plume L6 Pro, PGN-507, Plume P8 Pro, Allure M3 Lite, Griffe T8 Plus, Allure A8 Pro, TFX713L, PGN610, PGN513, PGN522, Allure M1, PGN606, TMK715L
- MobiWire: MobiPrint, Vodafone Pro 4G, SmartT23, V Lite 2, Hotah,
- Wintouch: K716, M704, K81Pro, K13, Q75S, K77, K717, K702, K81, K713, K12Pro, K701, M13, K718, M718, Q75X, M99, K11
- WALTON: Primo NF+, Primo G8, WALPAD8G, Walpad_10H, Primo H8, Walpad_G2, Primo GH9, Primo HM5, PRIMO N4, Primo H7s, Primo H6+, RX7 Mini, NEXG_N10, Primo GF3, Primo_RH2, Primo RM2, k200_1g, Primo NH2, Primo H9 Pro, Primo GH11, Primo H4, PRIMO S8. Primo H7. NEXG N9, Primo H10,XANON X20, Orbit Y50, XANON X90, Primo NH3 Lite, Primo RX7, Primo G7+, Primo S7, Primo HM4+, Primo NH Lite, Primo GM2 Plus, Primo N5, PRIMO RX8, PRIMO RX9,, Primo R5 Plus, Primo NF2, Primo E10, Primo NH, Primo GM2, Primo HM4i, k300, Primo ZX4, Primo NX2, Primo RM2 mini, Primo R9, Primo F6, Primo S3 mini, Primo GM3, Walpad G3, Primo E10 Plus, Primo EF9, Primo GH5 mini, WALPAD 10P, k510, Primo NH5, Primo F7, Primo GH6, Primo GH6+, Primo E11, Primo GF7, Primo NH4, Primo NH3, Primo D10, Primo R5, Primo GH7i, Primo N3, Primo NF4 2GB, Primo F7s,
- KGTEL: X5, R10
- Gtel: SL8, A718 Xplora Plus, Gtel X6pro, Gtel X7plus, Gtel X6s, Gtel Infinity X, A7155_X4_mini, A770_SL8_Pro, Gtel Vivo4, MX4, Gtel_X5pro, Gtel X6plus, Mx6, A704i Inspire-S, A715_Inspire_One, A7150_X4, A728_XP2, A770_XL7, Gtel_X5mini, Gtel_X5s, A737_XploraZ, Gtel Vivo PLUS, A7101_X3_mini, A713_Vivo_Pro, Gtel Infinity 8s, Gtel_X7pro, Gtel Infinity Alpha, Infinity_13, Delta_14, Gtel Infinity 9

Please login to view image

Added support for Unisoc based phones:
- Condor: Infinity a4, Griffe T9, Plume L4. Infinity e4, Griffe T8, Griffe T5
- MobiWire: IKOSORA+, H6682, Kicka 5 Plus 4G, V Pro 2, Halona, Airtel Imagine, Moov Smart Pro, H5111L, Awadjidje, Smart 1
- WALTON: ORBIT Y12, NEXG N71 Plus, NEXG N8, Primo R6 Max, NEXG N74, NEXG N71, NEXG N72, NEXG N70, NEXG N26, Primo GH10i, PRIMO F10, ORBIT Y21, NEXG N25, ORBIT Y70, NEXG N6, NEXG N73, ORBIT Y70c, Gtel_X7s, Gtel_Mx5, Primo H8 Pro, Primo H9, Primo HM7, Primo GH10, PRIMO EF10, Primo R6, Primo G9, Primo E12, Primo EF8 4G, y400, Primo G8i, Primo EM2, Primo HM6, Primo R10,
- KGTEL: X55E, A56

new download software
MEGA: https://mega.nz/file/GXgxkKSZ...

Plz add realme c63 4g for imei repair supporte

 

[GsmToto]

Selected model: Spreadtrum Spreadtrum
Operation: Read Flash Info
Software version: 7.11


onnect phone in BROM mode. Use volume key buttons or testpoint.
Waiting for device... OK
Device found at COM4
Port: USB\VID_1782&PID_4D00\6&1C0BB16A&1&4
Driver: [UNISOC Communications Inc.,sprdvcom,SPRD U2S Diag,sprdvcom.sys,4.19.38.134]
Port type: BROM
Connecting to device... OK
Selected processor: Tiger_T616_64
Load files... (universal) OK
Connect preloader 1... OK
Connect preloader 2... OK
Connect loader 1... OK
Connect loader 2... OK
Serial Number: 0F64B1372310058A
Flash Type: EMMC
Read partitions info... OK
Checking A/B state... OK [A]
Read product info... [EROFS] ... OK
Product Brand : realme
Product Manufacturer : realme
Product Model : ums9230_latte_Natv
Product Name : ums9230_latte_Natv
Product Device : ums9230_latte
Product Board : ums9230_latte
Board Platform : ums9230
Build ID : TP1A.220624.014
Build Date : Sun Sep 22 00:20:04 CST 2024
Display ID : TP1A.220624.014 release-keys
Security Patch : 2024-09-05
Version SDK : 34
Version Release : 14
Version Codename : REL
Firmware Version : 375
Userdata FS Type : F2FS
Done!

 

[elgollo38]

Please login to view image

Pandora 7.11. Release

Please login to view image

Please login to view image

Fixed bug with flashing Mediatek phones (Signature(Entity) invalid)

Please login to view image

Added support Samsung phones:
- Galaxy F23 SM-E236B (BIT

Please login to view image

- Galaxy M52 5G SM-M526B (BIT 5)
- Galaxy Tab S8 Ultra SM-X900 (BIT 9)
- Galaxy S23 Ultra SCG20 (BIT 1)

Please login to view image

Added new loader for Samsung:
- SM-A025A BIT 8
- SM-A057G BIT 5
- SM-A057M BIT 7
- SM-A235F BIT 9
- SM-A235M BIT 9
- SM-A236B BIT 9
- SM-A236E BIT 9
- SM-A426B BIT 8
- SM-G780G BIT D
- SM-G781B BIT E
- SM-G990B BIT B
- SM-M145F BIT 6
- SM-N986U BIT A
- SM-S908N BIT 6
- SM-S918B BIT 7

Please login to view image

Added support for Mediatek based phones:
- Condor: SP661, PAM524, TB109L, TB108W, TFX714L, Griffe T7, PGN517, Plume L5 Pro, Plume L2 Pro, SP531, SP659, Plume L1, Infinity E5, TFX712G, TB105L, Plume L5, PKT-301, Infinity e5 pro, PGN-404, Plume L3 Smart, Plume L8 Pro, Plume L6 Pro, PGN-507, Plume P8 Pro, Allure M3 Lite, Griffe T8 Plus, Allure A8 Pro, TFX713L, PGN610, PGN513, PGN522, Allure M1, PGN606, TMK715L
- MobiWire: MobiPrint, Vodafone Pro 4G, SmartT23, V Lite 2, Hotah,
- Wintouch: K716, M704, K81Pro, K13, Q75S, K77, K717, K702, K81, K713, K12Pro, K701, M13, K718, M718, Q75X, M99, K11
- WALTON: Primo NF+, Primo G8, WALPAD8G, Walpad_10H, Primo H8, Walpad_G2, Primo GH9, Primo HM5, PRIMO N4, Primo H7s, Primo H6+, RX7 Mini, NEXG_N10, Primo GF3, Primo_RH2, Primo RM2, k200_1g, Primo NH2, Primo H9 Pro, Primo GH11, Primo H4, PRIMO S8. Primo H7. NEXG N9, Primo H10,XANON X20, Orbit Y50, XANON X90, Primo NH3 Lite, Primo RX7, Primo G7+, Primo S7, Primo HM4+, Primo NH Lite, Primo GM2 Plus, Primo N5, PRIMO RX8, PRIMO RX9,, Primo R5 Plus, Primo NF2, Primo E10, Primo NH, Primo GM2, Primo HM4i, k300, Primo ZX4, Primo NX2, Primo RM2 mini, Primo R9, Primo F6, Primo S3 mini, Primo GM3, Walpad G3, Primo E10 Plus, Primo EF9, Primo GH5 mini, WALPAD 10P, k510, Primo NH5, Primo F7, Primo GH6, Primo GH6+, Primo E11, Primo GF7, Primo NH4, Primo NH3, Primo D10, Primo R5, Primo GH7i, Primo N3, Primo NF4 2GB, Primo F7s,
- KGTEL: X5, R10
- Gtel: SL8, A718 Xplora Plus, Gtel X6pro, Gtel X7plus, Gtel X6s, Gtel Infinity X, A7155_X4_mini, A770_SL8_Pro, Gtel Vivo4, MX4, Gtel_X5pro, Gtel X6plus, Mx6, A704i Inspire-S, A715_Inspire_One, A7150_X4, A728_XP2, A770_XL7, Gtel_X5mini, Gtel_X5s, A737_XploraZ, Gtel Vivo PLUS, A7101_X3_mini, A713_Vivo_Pro, Gtel Infinity 8s, Gtel_X7pro, Gtel Infinity Alpha, Infinity_13, Delta_14, Gtel Infinity 9

Please login to view image

Added support for Unisoc based phones:
- Condor: Infinity a4, Griffe T9, Plume L4. Infinity e4, Griffe T8, Griffe T5
- MobiWire: IKOSORA+, H6682, Kicka 5 Plus 4G, V Pro 2, Halona, Airtel Imagine, Moov Smart Pro, H5111L, Awadjidje, Smart 1
- WALTON: ORBIT Y12, NEXG N71 Plus, NEXG N8, Primo R6 Max, NEXG N74, NEXG N71, NEXG N72, NEXG N70, NEXG N26, Primo GH10i, PRIMO F10, ORBIT Y21, NEXG N25, ORBIT Y70, NEXG N6, NEXG N73, ORBIT Y70c, Gtel_X7s, Gtel_Mx5, Primo H8 Pro, Primo H9, Primo HM7, Primo GH10, PRIMO EF10, Primo R6, Primo G9, Primo E12, Primo EF8 4G, y400, Primo G8i, Primo EM2, Primo HM6, Primo R10,
- KGTEL: X55E, A56

new download software
MEGA: https://mega.nz/file/GXgxkKSZ...

Selected model: OPPO CPH2185 (OPPO A15)
Operation: Erase FRP
Software version: 7.10


Connect phone in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1633,usb2ser.sys,3.0.1504.0]
Device found at COM5 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1633,usb2ser.sys,3.0.1504.0]
Device found at COM5 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x76EA4B04, 0x5564494F, 0x1A606F57, 0x1548380B
Get Chip ID... [MT6765]
Get SOC ID... [3435018BAD22214131274257F18E150A4C472A5073D652F96A A5847237C05000]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90012DF0B7B54A68423861503E03008B
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: hB8aP>
EMMC_ID : 0x900142DF0B7B5A68423861503E03008B
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0747C00000 (29.12Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0080000000 (2.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: info not available
DeviceLifeTimeEstB: 20% - 30% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : OPPO
Product Manufacturer : OPPO
Product Model : CPH2185
Product Device : OP4F2F
Product Board : oppo6765
Board Platform : mt6765
Build ID : QP1A.190711.020
Build Date : Thu Feb 22 00:44:37 CST 2024
Display ID : CPH2185_11_A.69
Security Patch : 2023-02-05
Version SDK : 29
Version Release : 10
Version Codename : REL
Userdata FS Type : EXT4
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/OPPO_CPH2185%20(OPPO%20A15)/FRP_BACKUP_(2024-12-25_10-5-55)/
Format FRP... [P1] OK
Writting FRP data... OK
Erase FRP done!

Message from a z3x subscriber for 10 years

Dear Z3X friends, for many years we used the Z3x tool because it is one of the best, and many colleagues still have it but as a reminder because the company Z3x box or dongle replaced it with z3x pandora, pushing us aside without giving us the opportunity to migrate to the new z3x pandora tool that replaced z3x box or dongle, I think that we z3x box and dongle subscribers could have a more comfortable access with respect to the acquisition of z3x pandora, the only option they gave us was that we could migrate from z3x box and dongle with credits from the same, and for many subscribers it is the same as buying the service as a new user. We would like to be given an option to migrate to z3x pandora, thank you very much, we hope for a sensible response.

 

[GsmToto]

Selected model: Xiaomi Redmi 12 (Fire)
Operation: Repair
Software version: 7.11


Connect phone in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V2023,usb2ser_mtk.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM3 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V2023,usb2ser_mtk.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM3[BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x8A7057F0, 0x528D7A31, 0x3788A9CA, 0xCAFB1E06
Get Chip ID... [MT6768]
Get SOC ID... [C30DB4EDC5A4A58791ED0A44FF691744C26451821BD0347369 6D1C26772C023D]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [8]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0xD62D00470E633AA34D4D43313238510E
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: MMC128
EMMC_ID : 0xD62D00470E633AA34D4D43313238510E
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x1D1EC00000 (116.48Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : fire
Product Name : vnd_fire
Product Device : fire
Product Board : fire
Board Platform : mt6768
Build ID : TP1A.220624.014
Build Date : Wed Dec 6 15:36:41 UTC 2023
Display ID : TP1A.220624.014
Security Patch : 2023-12-01
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : V14.0.13.0.TMXMIGM
Userdata FS Type : F2FS
Read partition "nvdata"... OK
Read partition "protect1"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read security files... OK
Calculating... OK
Read IMEI... OK
IMEI 1: 3587428999665362
IMEI 2: 3567985346237076
Repairing IMEI...
IMEI 1: XXXXXXXXXXXX706
IMEI 2: XXXXXXXXXXXX834
Write IMEI and patch CERT [NVDATA]... OK
Load partiton for patching... [Nov 2024] ... OK
Write IMEI and patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security and Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.

 

[GsmToto]

Selected model: Samsung SM-A137F (Samsung Galaxy A13)
Operation: Erase FRP
Software version: 7.11

Connect phone in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1511.0]
You are using driver version 3.0.1511.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM2 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1511.0]
You are using driver version 3.0.1511.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM3 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x07A231DD, 0x32B675AD, 0x82AA491A, 0xEE7E7D9A
Get Chip ID... [MT6768]
Get SOC ID... [83D53F5EABAC0ACAA9FB9C06C5627D046FE02BDB768E5583EC 3BF27A857129HX]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [8]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x150100445C5B90F2A9FB836384D4200C
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: DX68MB
EMMC_ID : 0x15010044C5B90F2A9FB5836384D4200C
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0747C00000 (29.12Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [F2FS] ... OK
Product Brand : samsung
Product Manufacturer : samsung
Product Model : SM-A137F
Product Name : a13vensxx
Product Device : a13ve
Product Board : a13ve
Board Platform : mt6768
Build ID : SP1A.210812.016
Build Date : Mon Dec 4 10:46:16 +07 2023
Display ID : TP1A.220624.014.A137FXXS3CWL7
Security Patch : 2023-11-01
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : A137FXXS3CWL7
Userdata FS Type : F2FS
Read partition "frp"... OK
Read partition "persistent"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Samsung_SM-A137F%20(Samsung%20Galaxy%20A13)/FRP_BACKUP_(2025-1-8_20-21-54)/
Format FRP... [P1] [P2] OK
Writting FRP data... OK
Erase FRP done!

 

[GsmToto]

Selected model: Infinix X6528 (Infinix Hot 40i)
Operation: Erase FRP
Software version: 7.11


Connect phone in BROM mode. Use volume key buttons or testpoint.
Waiting for device... OK
Device found at COM5
Port: USB\VID_1782&PID_4D00\6&298C69D9&0&3
Driver: [UNISOC Communications Inc.,sprdvcom,SPRD U2S Diag,sprdvcom.sys,4.19.38.134]
Port type: BROM
Connecting to device... OK
Selected processor: Tiger_T612_64
Load files... (universal) OK
Connect preloader 1... OK
Connect preloader 2... OK
Connect loader 1... OK
Connect loader 2... OK
Serial Number: 11224640115983C3
Flash Type: UFS
Read partitions info... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : Infinix
Product Manufacturer : INFINIX
Product Model : Infinix X6528
Product Name : X6528-OP
Product Device : Infinix-X6528
Product Board : Infinix-X6528
Board Platform : ums9230
Build ID : TP1A.220624.014
Build Date : Mon Nov 18 10:26:45 CST 2024
Display ID : X6528-F069-T-OP-V1904-241118
Security Patch : 2024-11-05
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : 533
Userdata FS Type : F2FS
Backup partitions... OK
Formatting "persist" partition... OK
Done!

 

[GsmToto]

Selected model: Realme RMX3261 (Realme C21Y)
Operation: Erase FRP And Wipe
Software version: 7.11

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX or PC]
Connect phone in BROM mode. Use volume key buttons or testpoint.
Waiting for device... OK
Device found at COM3
Port: USB\VID_1787&PID_4D00\6&37F8BD07&0&2
Driver: [UNISOC Communications Inc.,sprdvcom,SPRD U2S Diag,sprdvcom.sys,4.19.38.134]
Port type: BROM
Connecting to device... OK
Selected processor: Tiger_T610_64
Load files... (REALME/RMX3261) OK
Connect preloader 1... OK
Connect preloader 2... OK
Connect loader 1... OK
Connect loader 2... OK
Serial Number: 00216D401B37292010HA070M
Read partitions info... OK
Checking A/B state... OK [A]
Read product info... [EXT4] ... OK
Product Brand : realme
Product Manufacturer : realme
Product Model : RMX3263
Product Name : RMX3263
Product Device : RMX3263
Product Board : RMX3263
Board Platform : ums512
Build ID : RP1A.201005.001
Build Date : Mon Apr 22 19:25:52 CST 2024
Display ID : RMX3261_11_A.119
Security Patch : 2024-02-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 1713785217562
Userdata FS Type : F2FS
Backup partitions... OK
Formatting "persist" partition... OK
Formatting "userdata" partition... OK
Formatting "cache" partition... OK
Formatting "metadata" partition... OK
Creating default filesystems... [CACHE: EXT4] ... [USERDATA: F2FS] ... OK
Done!

 

[GsmToto]

Selected model: Infinix X6528 (Infinix Hot 40i)
Operation: Erase FRP
Software version: 7.11


Connect phone in BROM mode. Use volume key buttons or testpoint.
Waiting for device... OK
Device found at COM5
Port: USB\VID_1782&PID_4D00\6&298C69D9&0&3
Driver: [UNISOC Communications Inc.,sprdvcom,SPRD U2S Diag,sprdvcom.sys,4.19.38.134]
Port type: BROM
Connecting to device... OK
Selected processor: Tiger_T612_64
Load files... (universal) OK
Connect preloader 1... OK
Connect preloader 2... OK
Connect loader 1... OK
Connect loader 2... OK
Serial Number: 11224644C30419815
Flash Type: UFS
Read partitions info... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : Infinix
Product Manufacturer : INFINIX
Product Model : Infinix X6528
Product Name : X6528-OP
Product Device : Infinix-X6528
Product Board : Infinix-X6528
Board Platform : ums9230
Build ID : TP1A.220624.014
Build Date : Mon Nov 18 10:26:45 CST 2024
Display ID : X6528-F069-T-OP-V1904-241118
Security Patch : 2024-11-05
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : 533
Userdata FS Type : F2FS
Backup partitions... OK
Formatting "persist" partition... OK
Done!

 

[GsmToto]

Selected model: Mediatek Mediatek
Operation: Unlock network
Software version: 7.11

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to [BOX] in BROM mode
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0717
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1511.0]
You are using driver version 3.0.1511.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM3 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0717
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x5272D588, 0x7019EEF7, 0x01E5B94C, 0x76CC8426
Get Chip ID... [MT6761]
Get SOC ID... [A41EEE81147D02524450A284DF348 E090C1FB02291A904FD1401A661E196449D]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [5]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0xF4012241523BAD4A313158105D39233E
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: ARJ11X
EMMC_ID : 0xF40122415243BADA313158105D39233E
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x0748000000 (29.13Gb)
RAM INFO:
INT_SRAM: 0x000003A500 (233.25Kb)
EXT_RAM : 0x0080000000 (2.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : TCL
Product Manufacturer : alps
Product Model : mssi_32_ago_ww
Product Board : rio_go
Board Platform : mt6761
Build ID : SP1A.210812.016
Build Date : Fri Sep 27 00:21:00 CST 2024
Display ID : TP1A.220624.014
Security Patch : 2024-08-05
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : NYB2
Userdata FS Type : F2FS
Read security partition from phone... OK
Read security files... OK
Read NVDATA files... OK
Calculating... OK
Read lock info... OK
Unlock... OK [DF1, GB2, UN]
Write lock info... OK
Write security partition to phone... OK
Network Unlock done!

 

[GsmToto]

Selected model: Samsung SM-A055F (Galaxy A05)
Operation: Wipe Partitions
Software version: 7.11
Erasing of partitions can damage your device.
If BROM was disabled and you want wipe preloader partition, phone will bricked. Recovery possible only with ISP mode. Continue? YES

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX or PC] in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM_V1632 (Android),usb2ser.sys,3.0.1504.0]
Device found at COM3 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0xC4823C73, 0xB44E05EC, 0xDD3DFFEC, 0x3260B0DE
Load DownloadAgent... OK
Search DA... OK [0]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [PRELOADER]
Preloader alive. Skip initializing external RAM
Send 2nd DA... OK
DA2 auth: disbled
Get device info... OK
EMMC INFO:
EMMC_CNAME: DC6DMB
EMMC_ID : 0x15010044A07AA8B674336444D420065C
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
[EFUSE INFO]: BROM not disabled
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : samsung
Product Manufacturer : samsung
Product Model : SM-A055F
Product Name : a05mxx
Product Device : a05m
Product Board : a05m
Board Platform : mt6768
Build ID : SP1A.210812.016
Build Date : Fri Oct 11 15:08:17 KST 2024
Firmware Version : A055FXXS7CXJ1
Userdata FS Type : F2FS
Format "frp" partition... OK
Format "persistent" partition... OK
Format "cache" partition... OK
Format "userdata" partition... OK
Format Partitions done!

 

[GsmToto]

Selected model: Spreadtrum Spreadtrum
Operation: Restore From Backup
Software version: 7.12


Connect phone in BROM mode. Use volume key buttons or testpoint.
Waiting for device... OK
Device found at COM3
Port: USB\VID_1782&PID_4D00\5&3A808860&0&5
Driver: [UNISOC Communications Inc.,sprdvcom,SPRD U2S Diag,sprdvcom.sys,4.19.38.134]
Port type: BROM
Connecting to device... OK
Selected processor: SC9863A
Load files... (universal) OK
Connect preloader 1... OK
Connect preloader 2... OK
Connect loader 1... OK
Connect loader 2... OK
Serial Number: 5065485958072736
Read partitions info... OK
Checking A/B state... OK [A]
Read product info... [EROFS] ... OK
Product Brand : ZTE
Product Manufacturer : ZTE
Product Model : ZTE Blade A54
Product Name : P963F64
Product Device : P963F64
Product Board : s9863a1h10
Board Platform : sp9863a
Build ID : TP1A.220624.014
Build Date : Fri Sep 1 07:13:40 CST 2023
Display ID : MyOS13.0.0_A54_AS
Security Patch : 2023-08-05
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : 20230901.0605482
Userdata FS Type : F2FS
Restore GPT... OK
Restore partition "avbmeta_rs_b"... OK
Restore partition "blackbox"... OK
Restore partition "boot_a"... OK
Restore partition "boot_b"... OK
Restore partition "cache"... OK
Restore partition "common_rs1_a"... OK
Restore partition "common_rs1_b"... OK
Restore partition "common_rs2_a"... OK
Restore partition "common_rs2_b"... OK
Restore partition "dtb_a"... OK
Restore partition "dtb_b"... OK
Restore partition "dtbo_a"... OK
Restore partition "dtbo_b"... OK
Restore partition "fbootlogo"... OK
Restore partition "hypervsior_a"... OK
Restore partition "hypervsior_b"... OK
Restore partition "init_boot_a"... OK
Restore partition "init_boot_b"... OK
Restore partition "l_deltanv_a"... OK
Restore partition "l_deltanv_b"... OK
Restore partition "l_fixnv1_a"... OK
Restore partition "l_fixnv1_b"... OK
Restore partition "l_fixnv2_a"... OK
Restore partition "l_fixnv2_b"... OK
Restore partition "l_gdsp_a"... OK
Restore partition "l_gdsp_b"... OK
Restore partition "l_ldsp_a"... OK
Restore partition "l_ldsp_b"... OK
Restore partition "l_modem_a"... OK
Restore partition "l_modem_b"... OK
Restore partition "l_runtimenv1"... OK
Restore partition "l_runtimenv2"... OK
Restore partition "logo_a"... OK
Restore partition "logo_b"... OK
Restore partition "metadata"... OK
Restore partition "misc"... OK
Restore partition "miscdata"... OK
Restore partition "persist"... OK
Restore partition "avbmeta_rs_a"... OK
Restore partition "pm_sys_a"... OK
Restore partition "pm_sys_b"... OK
Restore partition "prodnv"... OK
Restore partition "sml_a"... OK
Restore partition "sml_b"... OK
Restore partition "splloader"... OK
Restore partition "splloader_bak"... OK
Restore partition "super"... OK
Restore partition "sysdumpdb"... OK
Restore partition "teecfg_a"... OK
Restore partition "teecfg_b"... OK
Restore partition "trustos_a"... OK
Restore partition "trustos_b"... OK
Restore partition "uboot_a"... OK
Restore partition "uboot_b"... OK
Restore partition "uboot_log"... OK
Restore partition "userdata"... OK
Restore partition "vbmeta_a"... OK
Restore partition "vbmeta_b"... OK
Restore partition "vbmeta_odm_a"... OK
Restore partition "vbmeta_odm_b"... OK
Restore partition "vbmeta_product_a"... OK
Restore partition "vbmeta_product_b"... OK
Restore partition "vbmeta_system_a"... OK
Restore partition "vbmeta_system_b"... OK
Restore partition "vbmeta_system_ext_a"... OK
Restore partition "vbmeta_system_ext_b"... OK
Restore partition "vbmeta_vendor_a"... OK
Restore partition "vbmeta_vendor_b"... OK
Restore partition "vendor_boot_a"... OK
Restore partition "vendor_boot_b"... OK
Restore partition "ztecfg"... OK
Restore partition "ztepersist"... OK
Done!