elected model: OPPO PGCM10 (Oppo K9x)
Operation: Repair
Software version: 6.9
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1633,usb2ser.sys,3.0.1504.0]
Device found at COM19 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1633,usb2ser.sys,3.0.1504.0]
Device found at COM19 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xA0A7C56E, 0x4E75F652, 0x46D0D8A8, 0x433D759C
Get Chip ID... [MT6833]
Get SOC ID... [B74F1ADAF84FC9D0A8193002DA16C3DE8A1013CB408C9887BE70D2DC533246E3]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM8L9001JM-B624 (0700)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM8L9001JM-B624
UFS_FWVER : 0700
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : alps
Product Manufacturer : alps
Product Model : PGCM10
Product Name : vnd_oppo6833
Product Device : oppo6833
Product Board : oppo6833
Board Platform : mt6833
Build ID : RP1A.200720.011
Build Date : Fri Sep 2 21:01:26 CST 2022
Display ID : PGCM10_11_A.08
Security Patch : 2022-07-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 1662122329752
Userdata FS Type : F2FS
Read security partition from phone...
Decrypting security data... OK
Encrypt security data... OK
Read partition "nvdata"... OK
Read partition "protect1"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read security files... OK
Calculating... OK
Repairing IMEI...
IMEI 1: 3534998xxxxxxxx
IMEI 2: 3534998xxxxxxxx
Write IMEI and patch CERT [NVDATA]... OK
Checking patch type... [2]
Patching CERT... OK
Save patched partiton... OK
Updating NVRAM... OK
Write IMEI and patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security and Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.
Operation: Repair
Software version: 6.9
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1633,usb2ser.sys,3.0.1504.0]
Device found at COM19 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1633,usb2ser.sys,3.0.1504.0]
Device found at COM19 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xA0A7C56E, 0x4E75F652, 0x46D0D8A8, 0x433D759C
Get Chip ID... [MT6833]
Get SOC ID... [B74F1ADAF84FC9D0A8193002DA16C3DE8A1013CB408C9887BE70D2DC533246E3]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM8L9001JM-B624 (0700)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM8L9001JM-B624
UFS_FWVER : 0700
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : alps
Product Manufacturer : alps
Product Model : PGCM10
Product Name : vnd_oppo6833
Product Device : oppo6833
Product Board : oppo6833
Board Platform : mt6833
Build ID : RP1A.200720.011
Build Date : Fri Sep 2 21:01:26 CST 2022
Display ID : PGCM10_11_A.08
Security Patch : 2022-07-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 1662122329752
Userdata FS Type : F2FS
Read security partition from phone...
Decrypting security data... OK
Encrypt security data... OK
Read partition "nvdata"... OK
Read partition "protect1"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read security files... OK
Calculating... OK
Repairing IMEI...
IMEI 1: 3534998xxxxxxxx
IMEI 2: 3534998xxxxxxxx
Write IMEI and patch CERT [NVDATA]... OK
Checking patch type... [2]
Patching CERT... OK
Save patched partiton... OK
Updating NVRAM... OK
Write IMEI and patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security and Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.
