★★ Post Here All Successful Stories By Infinity-Box CM/CM2- ★★

maanarman · Dec 7, 2018

Qmobile S3 Factory Reset Done

Code:

Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 24 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4841473265050750A33E774331
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e2GA
[eMMC] : FLASH_CID : 90014A4841473265050750A33E774331
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003AB800000
[eMMC] : FLASH_UCP : 15032 MiB [eMMC 16 GiB]
DEV RID    : 0x644765A7AA596DA9DCD0910707CE7EF7
INT RAM    : 0x00020000
EXT RAM    : 0x80000000 [2 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!
Clear DIN
Clear Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:57
Reconnect Power/Cable!

maanarman · Dec 8, 2018

Itel It5020 Hang Logo Done

Code:

SPRD mode : SC6531 : REV : C000 : NOR

Operation : Identify [ v1.03 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
BootSource  :  InternalLibrary
BootVersion : Spreadtrum Boot Block version 1.2
Port speed : 921600
FDL Flash  : Control transfered!

Boot Done!

CS0_MEM : SPI : [GIGADEVICE] : GD25Q64 : 0x00800000 [ 8MiB ]

IMEI[1] : 354269088492122
IMEI[2] : 354269088492130

Done!
Elapsed: 00:00:14

Reconnect Power/Cable!

Operation : Format FileSystem [ v1.03 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
BootSource  :  InternalLibrary
BootVersion : Spreadtrum Boot Block version 1.2
Port speed : 921600
FDL Flash  : Control transfered!

Boot Done!

CS0_MEM : SPI : [GIGADEVICE] : GD25Q64 : 0x00800000 [ 8MiB ]

Make backup of sensetive data
Backup saved to : C:\InfinityBox\CM2SCR\Backup\00800000_FMT_BACK_0C8BF6EFD068_NVM.nv

Executing FormatFFS ...
Format FFS Done!

Done!
Elapsed: 00:00:17

Reconnect Power/Cable!

maanarman · Dec 8, 2018

Samsung j327vpp Write Flash Done

Code:

Phone found on COM136

Phone In Download mode...
Port open Ok!
LOKE received!
Prepare Ok!
Enter Setup...
Setup Done!
Try download PIT...
Download PIT Ok!
Start flashing!

Flashing aboot.mbn
Flashing sbl1.mbn
Flashing rpm.mbn
Flashing tz.mbn
Flashing devcfg.mbn
Flashing NON-HLOS.bin
Flashing cmnlib.mbn
Flashing keymaster.mbn
Flashing lksecapp.mbn
Flashing sec.dat
Flashing apdp.mbn
Flashing msadp.mbn
Flashing boot.img
Flashing recovery.img
Flashing system.img.ext4
Flashing persist.img.ext4
Flashing userdata.img.ext4
Flashing modem.bin
Flashing adspso.bin
Flashing cache.img.ext4
Flashing done

Reboot phone...


Phone Disconnected

maanarman · Dec 8, 2018

Samsung J700h Clone Flash Done

Code:

Scatter Load Ok , BaseBand : MT6589 , Project : MTK6589 , Storage : eMMC
Files found : 11 , Set to Flash : 10
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand   : samsung
Device Model   : j73g
Device CPU     : MT6589
Device IntName : j73gxx
Device Version : 6.0
Device Compile : 1/11/2016 3:11:53 AM
Device Project : ALPS.JB2.MP.V1.16
Device ExtInfo : SM-J700H
Ready to Flash!

Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 47 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6583
BB_CPU_NME : [MediaTek] MT6583|6589_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.3.2 on BBID : 0x86
NAND Flash : NOT INSTALLED
eMMC Flash : 484A019064314734A205860417901E7D
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164048605A27D1E9017
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID    : 0x644765A73FAF0D5A978BEC06CFE1CDCF
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6589 , Project : MTK6589 , Storage : eMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Enabled
Setting : HW verify :  Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Skip checking by User request!

BL : BatteryLevel : 4068 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000001400000-0x0000000000100000
Erase : 0x0000000003520000-0x00000000377E0000
Flash Pre-Erase Done, time used : 00:00:00

SecCfg Passed , 1799
BMT remark not need. Will skip

Preloader Download skipped by user request!
PartCount : 0013
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : MBR
Image Flash Ok
Flash now : EBR1
Image Flash Ok
Flash now : UBOOT
Image Flash Ok
Flash now : BOOTIMG
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SEC_RO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : ANDROID
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USRDATA
Image Flash Ok
Flash Write Done, time used : 00:02:44

Processing : Verify
Verify Passed : MBR
Verify Passed : EBR1
Verify Passed : UBOOT
Verify Passed : BOOTIMG
Verify Passed : RECOVERY
Verify Passed : SEC_RO
Verify Passed : LOGO
Verify Passed : ANDROID
Verify Passed : CACHE
Verify Passed : USRDATA
Data Verify Done, time used : 00:00:26

Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:03:20
Reconnect Power/Cable!

maanarman · Dec 8, 2018

Samsung J120a Write Flash Done

Code:

Port open Ok!
LOKE received!
Prepare Ok!
Enter Setup...
Setup Done!
Try download PIT...
Download PIT Ok!
Start flashing!

Flashing sboot.bin
Flashing param.bin
Flashing boot.img
Flashing recovery.img
Flashing system.img
Flashing modem.bin
Flashing cache.img
Flashing done

Reboot phone...


Phone Disconnected

maanarman · Dec 8, 2018

Vgotel Ocean 6 FRP Remove Done

Code:

Operation : Check/Read Info [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 73 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ...

Model Name  : VGOTEL_OCEAN_6
Model Brand : VGOTEL
Model Device: VGOTEL_OCEAN_6
AndrVersion : 7.0
BaseBand CPU: SP7731CEA
CompileDate : 1/16/2018 12:39:21 PM
Project Ver : VGOTEL_OCEAN_6_V06_26122017
Model Ext   : Ocean 6

ExtraInfo : HWInfo not exists, normal phone

Elapsed: 00:00:15

Reconnect Power/Cable!


Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 73 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size  : 0x00000000FBAF7000
State : 0x0001

Mount : /cache
Size  : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x/6.x : Reset FRP Lock
Reset Ok!


Done!

Elapsed: 00:00:23

Reconnect Power/Cable!

maanarman · Dec 8, 2018

Qmobile A10 Read FF Done

Code:

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 47 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6575
BB_CPU_NME : [MediaTek] MT6575|MT6577_S00
BB_CPU_EXT : 0xCB00 , 0x8B00 , 0xE201
Processing BROM stage
i2c Init : 0300771F
SpeedSet : 0000
VChrgSet : 0x28 , BatStat : 0x02
WD Disable stat : 0x0000
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.3.2 on BBID : 0x84
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , HYNIX
[eMMC] : FLASH_CID : 90014A2058494E594816A148E00F109D
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID    : 0x644765A7E239473203C17AC7DFE992A1
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : A10
ProdName  : A10
ProdModel : A10
Device    : A10
AndroidVer: 4.1.1
MTKxCPU   : MT6577
MTKxPRJ   : ALPS.JB.MP.V1

Done!
Elapsed: 00:00:37
Reconnect Power/Cable!


Operation : Read Flash [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 47 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6575
BB_CPU_NME : [MediaTek] MT6575|MT6577_S00
BB_CPU_EXT : 0xCB00 , 0x8B00 , 0xE201
Processing BROM stage
i2c Init : 0300771F
SpeedSet : 0000
VChrgSet : 0x28 , BatStat : 0x02
WD Disable stat : 0x0000
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.3.2 on BBID : 0x84
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , HYNIX
[eMMC] : FLASH_CID : 90014A2058494E594816A148E00F109D
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID    : 0x644765A7E239473203C17AC7DFE992A1
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Content now ...

Brand     : A10
ProdName  : A10
ProdModel : A10
Device    : A10
AndroidVer: 4.1.1
MTKxCPU   : MT6577
MTKxPRJ   : ALPS.JB.MP.V1

[Read Ok] : preloader_s9081.bin
[Read Ok] : DSP_BL
[Read Ok] : MBR
[Read Ok] : EBR1
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : logo.bin
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img

[ScatCFG] : MT6577 / V1.0.0 / s9081 / EMMC
Android Info saved
MAUI Meta DB saved
HWConfig Info saved
FW Size : 809 MiB
Scatter saved to : C:\Users\test\Desktop\TEMP\MT6577__A10__A10__A10__4.1.1__ALPS.JB.MP.V1\

All done!

Done!
Elapsed: 00:05:04
Reconnect Power/Cable!

maanarman · Dec 8, 2018

Samsung I5.5 FRP Remove Done

Code:

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 73 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v4 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size  : 0x00000001279F7000
State : 0x0001

Mount : /cache
Size  : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x/6.x : Reset FRP Lock
Reset Ok!


Done!

Elapsed: 00:00:18

Reconnect Power/Cable!

maanarman · Dec 8, 2018

Qmobile i6 Metal One Write Flash Done

Code:

Operation : Check/Read Info [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 73 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ...

Model Name  : i6_Metal_ONE
Model Brand : QMobile
Model Device: i6_Metal_ONE_new
AndrVersion : 6.0
BaseBand CPU: I6_METAL_ONE
CompileDate : 2/28/2017 10:16:31 AM
Project Ver : MRA58K release-keys
Model Ext   : QMobile i6 Metal ONE

ExtraInfo : HWInfo not exists, normal phone

Elapsed: 00:00:21

Reconnect Power/Cable!


Infinity SC Firmware Detected
FW Size : 2874 MiB
Load Ok!

File Info
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand   : QMobile
Device Model   : i6_Metal_ONE_new
Device CPU     : i6_Metal_ONE
Device IntName : i6_Metal_ONE
Device Version : 6.0
Device Compile : 12/15/2016 10:31:38 AM
Device Project : MRA58K release-keys
Device ExtInfo : QMobile i6 Metal ONE


Operation : Flash [ v1.27 ]

======= Flash
Files set for flashing :
[ MCU ] : SC77xx Infinity Package

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 73 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!

PMTManager : Load 0x19 records
PMTManager : PMT Update Ok!
Flashing now

Update BootCode : u-boot-spl-16k.bin
Write Data ...
Write Data Ok!

Update BootCode : u-boot.bin
Erase block ...
Block erase Ok!
Write Data ...
Write Data Ok!

Write FSImage : prodnv.img
Write Data ...
Write Data Ok!

Write CodeData : sc7731C_CP0_modem.bin
Write Data ...
Write Data Ok!

Write CodeData : DSP_DM_Gx.bin
Write Data ...
Write Data Ok!

Erase Block : RuntimeData
Erase block ...
Block erase Ok!

Write CodeData : sc8830g_modem_CP2_WCN_Trunk_W16.28.5_Release.bin
Write Data ...
Write Data Ok!

Erase Block : RuntimeData
Erase block ...
Block erase Ok!

Write CodeData : logo_480x854.bin
Write Data ...
Write Data Ok!

Write CodeData : fblogo_480x854.bin
Write Data ...
Write Data Ok!

Write CodeData : boot.img
Write Data ...
Write Data Ok!

Write FSImage : system.img
Write Data ...
Write Data Ok!

Erase Block : PERSIST
Erase block ...
Block erase Ok!

Write CodeData : sysinfo.img
Write Data ...
Write Data Ok!

Write FSImage : cache.img
Write Data ...
Write Data Ok!

Write CodeData : recovery.img
Write Data ...
Write Data Ok!

Erase Block : MISC
Erase block ...
Block erase Ok!

Write FSImage : userdata.img
Write Data ...
Write Data Ok!


Elapsed: 00:04:41

Reconnect Power/Cable!

maanarman · Dec 8, 2018

Qmobile X2 Hang Logo Done

Code:

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 140 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6571
BB_CPU_NME : [MediaTek] MT6571_S00
BB_CPU_EXT : 0xCA00 , 0x8D00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8B
NAND Flash : 009800BC009000660076001600080000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0011 , [KINGSTON] KTN0403CS_TCR1
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0016 0008
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
DEV RID    : 0x644765A7D056096B8340A1616615D9B3
INT RAM    : 0x00020000
EXT RAM    : 0x10000000 [256 MiB]
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : QMobile
ProdName  : s3510ap
ProdModel : QMobile X2
Device    : s3510ap
AndroidVer: 4.4.2
MTKxCPU   : MT6571
MTKxPRJ   : ALPS.KK1.MP7.V1

Done!
Elapsed: 00:00:11
Reconnect Power/Cable!


Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 140 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6571
BB_CPU_NME : [MediaTek] MT6571_S00
BB_CPU_EXT : 0xCA00 , 0x8D00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8B
NAND Flash : 009800BC009000660076001600080000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0011 , [KINGSTON] KTN0403CS_TCR1
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0016 0008
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
DEV RID    : 0x644765A7D056096B8340A1616615D9B3
INT RAM    : 0x00020000
EXT RAM    : 0x10000000 [256 MiB]
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:15
Reconnect Power/Cable!

maanarman · Dec 8, 2018

Qmobile X32 Write Flash Done

Code:

Set mode to : SP [SC773x] eMMC [Android 6.x]

Operation : Check/Read Info [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 73 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ...

Model Name  : X32
Model Brand : QMobile
Model Device: X32
AndrVersion : 6.0
BaseBand CPU: X32
CompileDate : 11/22/2016 2:40:54 AM
Project Ver : MRA58K release-keys
Model Ext   : QMobile X32

ExtraInfo : HWInfo not exists, normal phone

Elapsed: 00:00:18

Reconnect Power/Cable!


Infinity SC Firmware Detected
FW Size : 2579 MiB
Load Ok!

File Info
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand   : QMobile
Device Model   : X32
Device CPU     : X32
Device IntName : X32
Device Version : 6.0
Device Compile : 11/22/2016 2:40:54 AM
Device Project : MRA58K release-keys
Device ExtInfo : QMobile X32


Operation : Flash [ v1.27 ]

======= Flash
Files set for flashing :
[ MCU ] : SC77xx Infinity Package

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 73 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!

PMTManager : Load 0x19 records
PMTManager : PMT Update Ok!
Flashing now

Update BootCode : u-boot-spl-16k.bin
Write Data ...
Write Data Ok!

Update BootCode : u-boot.bin
Erase block ...
Block erase Ok!
Write Data ...
Write Data Ok!

Write FSImage : prodnv.img
Write Data ...
Write Data Ok!

Write CodeData : sc7731C_CP0_modem.bin
Write Data ...
Write Data Ok!

Write CodeData : DSP_DM_Gx.bin
Write Data ...
Write Data Ok!

Erase Block : RuntimeData
Erase block ...
Block erase Ok!

Write CodeData : sc8830g_modem_CP2_WCN_Trunk_W16.28.5_Release.bin
Write Data ...
Write Data Ok!

Erase Block : RuntimeData
Erase block ...
Block erase Ok!

Write CodeData : logo_480x800.bin
Write Data ...
Write Data Ok!

Write CodeData : fblogo_480x800.bin
Write Data ...
Write Data Ok!

Write CodeData : boot.img
Write Data ...
Write Data Ok!

Write FSImage : system.img
Write Data ...
Write Data Ok!

Erase Block : PERSIST
Erase block ...
Block erase Ok!

Write CodeData : sysinfo.img
Write Data ...
Write Data Ok!

Write FSImage : cache.img
Write Data ...
Write Data Ok!

Write CodeData : recovery.img
Write Data ...
Write Data Ok!

Erase Block : MISC
Erase block ...
Block erase Ok!

Write FSImage : userdata.img
Write Data ...
Write Data Ok!


Elapsed: 00:03:55

Reconnect Power/Cable!

sadiqhussain0312 · Dec 8, 2018

Motorola xt1609 frp remove done

Code:

1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1609
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1609
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1609
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:00:35

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : harpia_vzw
Model  : XT1609
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:11

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:04

sadiqhussain0312 · Dec 8, 2018

Samsung g935t write flash done

Code:

Phone found on COM52

Phone In Download mode...
Port open Ok!
LOKE received!
Prepare Ok!
Enter Setup...
Setup Done!
Re-Partition enabled
Uploading Pit File
Start Flashing PIT
Prepare PIT
Flashing...
Flashing PIT done
Try download PIT...
Download PIT Ok!
Start flashing!

Flashing emmc_appsboot.mbn
Flashing lksecapp.mbn
Flashing xbl.elf
Flashing tz.mbn
Flashing hyp.mbn
Flashing devcfg.mbn
Flashing pmic.elf
Flashing rpm.mbn
Flashing cmnlib.mbn
Flashing keymaster.mbn
Flashing apdp.mbn
Flashing msadp.mbn
Flashing cmnlib64.mbn
Flashing sec.dat
Flashing NON-HLOS.bin
Flashing boot.img
Flashing recovery.img
Flashing system.img.ext4
Flashing persist.img.ext4
Flashing modem.bin
Flashing adspso.bin
Flashing cache.img.ext4
Flashing done

Reboot phone...

maanarman · Dec 8, 2018

J320fn flash done

Code:

Phone In Download mode...
Port open Ok!
LOKE received!
Prepare Ok!
Enter Setup...
Setup Done!
Try download PIT...
Download PIT Ok!
Start flashing!

Flashing boot.img
Flashing recovery.img
Flashing system.img
Flashing cache.img
Flashing SPRDWDSP.img
Flashing SPRDCP.img
Flashing SPRDGDSP.img
Flashing SPRDLTEDSP.img
Flashing nvitem.bin
Flashing PM_sharkl_arm7.bin
Flashing done

Reboot phone...


Phone Disconnected

Phone found on COM276

Phone In Download mode...

maanarman · Dec 8, 2018

Motorola Turbo FRP Remove Done

Code:

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:04:59

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : quark_verizon
Model  : XT1254
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:12

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:09

maanarman · Dec 8, 2018

Motorola Xt1609 FRP Remove Done

Code:

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1609
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1609
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1609
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:03:30

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : harpia_vzw
Model  : XT1609
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:13

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:12

maanarman · Dec 8, 2018

Samsung J701F Write Flash done

Code:

  FLASH INSTRUCTIONS:
  1. Choose correct flash file(s).
  2. If you have PIT file chosen, then you must check 'Repartition' option.
  3. Check flashing options if needed (Repartition, EFS clear, Boot update).
  4. Power on the phone in download mode (turn off phone, press vol.down + home + power).
  5. Connect the phone to PC with USB cable, install drivers if needed.
  6. Press 'Flash' button.

Operation: Flash
Selected model: SM-J701F
Software version: 33.5

File analysis... OK
Total file size: 0xA3B9E0A0 (2619 Mb)
Searching USB Flash interface... COM52 detected
Setup connection... OK
Set PIT file... OK
Reading PIT from phone... OK
Sending sboot.bin... OK
Sending param.bin... OK
Sending cm.bin... OK
Sending boot.img... OK
Sending recovery.img... OK
Sending system.img... OK
Sending modem.bin... OK
Sending modem_debug.bin... OK
Flashing done (time - 00:02:40)

Done with Samsung Tool PRO v.33.5

maanarman · Dec 8, 2018

Motorola Turbo FRP Remove Done

Code:

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:03:25

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : quark_verizon
Model  : XT1254
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:12

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 

Error : Device NOT accept CMD/Data!
Remove battery, cable. Check cable and connection. Repeat operation!


Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:05

maanarman · Dec 9, 2018

Qmobile x32 Write Flash Done

Code:

 Action : Read Info
 Tips:
 1.Remove Battery, Insert usb cable, Insert battery
 2.power off Phone, Remove & Reinsert Battery , insert USB Cable
 (In Case Some Phone Required to hold bootkey)
 Waiting for Phone Usb...
 Phone found [ USB Port:COM47 ]
 Connecting...
 Connection Done.
 Read CPU Info...
 CPU_SW: 0000
 CPU_HW: CA00
 CPU_ID: 6580
 BV: 01
 SecConf: 00000000
 uploading boot image to RAM...
 Handshake received from Phone.
 Detected eMMC FlashType.
 uploading boot image to RAM...
 Handshake Received from Phone.
 eMMC cid: 880103455041313030
 CHIP     : MT65800000
 CPU ID   :
 EMMC ID  : 880103455041313030
 EMMC Size: 8GB,  usable capacity: 7.23GB
 EMMC Name: EMMC_Device_EPA100
 Boot Information completed.
 
 Reading Project Property ...
 
 Brand          : QMobile
 Phone Model    : QMobile X32
 Android Ver    : 6.0
 CPU/Processor  : MT6580
 MTK Project ver: ALPS.W10.24.p0
 SW Version     : MRA58K release-keys
 Userdata State : Normal
 
 Action completed
 Time taken : 00:00:11
 Reconnect Battery/USB Cable
 CS-Tool Ver 1.60



 Action : Write Flash
 Tips:
 1.Remove Battery, Insert usb cable, Insert battery
 2.power off Phone, Remove & Reinsert Battery , insert USB Cable
 (In Case Some Phone Required to hold bootkey)
 Waiting for Phone Usb...
 Phone found [ USB Port:COM47 ]
 Connecting...
 Connection Done.
 Read CPU Info...
 CPU_SW: 0000
 CPU_HW: CA00
 CPU_ID: 6580
 BV: 01
 SecConf: 00000000
 uploading boot image to RAM...
 Handshake received from Phone.
 Detected eMMC FlashType.
 uploading boot image to RAM...
 Handshake Received from Phone.
 eMMC cid: 880103455041313030
 CHIP     : MT65800000
 CPU ID   :
 EMMC ID  : 880103455041313030
 EMMC Size: 8GB,  usable capacity: 7.23GB
 EMMC Name: EMMC_Device_EPA100
 Read Hardware Information is done.
 Loading scatter file ...
 Read CFG done.
 Checking the firmware matches the current BB ...
 firmware is valid.
 Image Format: General
 Downloading lk ......ok
 Downloading boot ......ok
 Downloading recovery ......ok
 Downloading logo ......ok
 Downloading secro ......ok
 Downloading system ......ok
 Downloading cache ......ok
 Downloading userdata ......ok
 Updating rom info ......ok
 All done.
 
 Action completed
 Time taken : 00:05:18
 Reconnect Battery/USB Cable
 CS-Tool Ver 1.60

maanarman · Dec 9, 2018

Qmobile Z12 FRP Remove Done

Code:

Chinese Miracle II  [MTK module] v 1.58

Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 47 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6735
BB_CPU_NME : [MediaTek] MT6735_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 520001154D423132D5A40642750514DC
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMB12
[eMMC] : FLASH_CID : 150100523231424D4206A4D5DC141375
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x0000000747C00000
[eMMC] : FLASH_UCP : 29820 MiB [eMMC 32 GiB]
DEV RID    : 0x644765A7B80D4ADF79DC86AB780C3303
INT RAM    : 0x00020000
EXT RAM    : 0xC0000000 [3 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!

Done!
Elapsed: 00:00:11
Reconnect Power/Cable!

★★ Post Here All Successful Stories By Infinity-Box CM/CM2- ★★

Friend's Martview

Friend's Martview

Friend's Martview

Friend's Martview

Friend's Martview

Friend's Martview

Friend's Martview

Friend's Martview

Friend's Martview

Friend's Martview

Friend's Martview

Junior Member

Junior Member

Friend's Martview

Friend's Martview

Friend's Martview

Friend's Martview

Friend's Martview

Friend's Martview

Friend's Martview