★★ Post Here All Successful Stories By Infinity-Box CM/CM2- ★★

[maanarman]

Qmobile I6i FRP Remove Done

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 150100464A32374D42025F2FE0F0724B
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM72J
[eMMC] : FLASH_CID : 150100464A32374D42025F2FE0F0724B
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID    : 0x644765A75817B403311C92359C728DCB
INT RAM    : 0x00020000
EXT RAM    : 0x30000000 [768 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : QMobile
ProdName  : QMobile i6i
ProdModel : QMobile i6i
Device    : QMobile
AndroidVer: 5.1
MTKxCPU   : MT6580
MTKxPRJ   : ALPS.L1.MP6.V2_TINNO6580.WE.L

Done!
Elapsed: 00:00:08
Reconnect Power/Cable!


Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 150100464A32374D42025F2FE0F0724B
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM72J
[eMMC] : FLASH_CID : 150100464A32374D42025F2FE0F0724B
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID    : 0x644765A75817B403311C92359C728DCB
INT RAM    : 0x00020000
EXT RAM    : 0x30000000 [768 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!
Clear DIN
Clear Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:26
Reconnect Power/Cable!

 

[maanarman]

Qmobile I8i FRP Remove Done

Set mode to : SP [SC773x] eMMC [Android 6.x]

Operation : Check/Read Info [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ...

Model Name  : I8i
Model Brand : QMobile
Model Device: I8i
AndrVersion : 6.0
BaseBand CPU: SP7731CEA
CompileDate : 7/21/2017 11:50:35 AM
Project Ver : QMobile I8i_MP_21_07
Model Ext   : QMobile I8i

ExtraInfo : HWInfo not exists, normal phone

Elapsed: 00:00:23

Reconnect Power/Cable!


Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size  : 0x0000000133CF7000
State : 0x0001

Mount : /cache
Size  : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x/6.x : Reset FRP Lock
Reset Ok!


Done!

Elapsed: 00:00:21

Reconnect Power/Cable!

 

[maanarman]

Qmobile M350 FRP Remove Done

Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 150100463732324D4200F8439755A3D9
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM227
[eMMC] : FLASH_CID : 150100463732324D4200F8439755A3D9
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0x644765A70CB347D5F1888DA343BBD637
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!

Done!
Elapsed: 00:00:11
Reconnect Power/Cable!

 

[maanarman]

Qmobile S2 Write FF Done

Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 140 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4838473165050719A120698225
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e1G8
[eMMC] : FLASH_CID : 90014A4838473165050719A120698225
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0x644765A77A32A0AE4006855E90603F20
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6580 , Project : s5250 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Enabled
Setting : HW verify :  Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Skip checking by User request!

BL : BatteryLevel : 3805 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000001C80000-0x0000000003320000
Erase : 0x00000000050A0000-0x00000001CBEE0000
Flash Pre-Erase Done, time used : 00:00:04

SecCfg Passed , 1799
BMT remark not need. Will skip

Preloader Download skipped by user request!
PartCount : 0014
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : LK
Image Flash Ok
Flash now : BOOT
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : SECRO
Image Flash Ok
Flash now : SYSTEM
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:04:12

Processing : Verify
Verify Passed : LK
Verify Passed : BOOT
Verify Passed : RECOVERY
Verify Passed : LOGO
Verify Passed : SECRO
Verify Passed : SYSTEM
Verify Passed : CACHE
Verify Passed : USERDATA
Data Verify Done, time used : 00:00:02

Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:04:29
Reconnect Power/Cable!

 

[maanarman]

Moto E2 FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : iled to get property ro.boot.hardware.sku, err = 0, status = 1; Property ro.boot.hardware.sku not
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : iled to get property ro.boot.hardware.sku, err = 0, status = 1; Property ro.boot.hardware.sku not
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : iled to get property ro.boot.hardware.sku, err = 0, status = 1; Property ro.boot.hardware.sku not
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:02:18

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : surnia_att
Model  : MotoE2(4G-LTE)
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:14

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:07

 

[maanarman]

Moto E4 FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:01:47

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : perry_verizon_f
Model  : Moto E (4)
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:16

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:07

 

[shahbazali]

 

[maanarman]

Vgotel I10 Write Flash Done

Load File
File_Info   : FISE61D_11C_PCB01_gprs_MT6261_S00.MAUI_11C_W13_52_MP_V2_F9.bin
FileVersion : MAUI.11C.W13.52.MP.V2.F9
Load File Ok

Operation : Flash [ v1.58 ]

======= Flash
Files set for flashing :
[ MCU ] : I10 VGOTEL FISE61D_11C_PCB01_GPRS_MT6261_S00.MAUI_11C_W13_52_MP_V2_F9

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 6 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CA02
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0000
BB_CPU_SN : 06CACB665E330D21E66879ABA944FF80
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_INFO   : 0xC0 , Ver : 3.2 , BBID : 0x8E
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x0112 , [MXIC] MX25L3291FWJI_09
[0] : FLASH_DIE : 00C2 0020 0016 0000
[0] : FLASH_LEN : 0x00400000
SDS_INFO : 0x003FE000 , 0x00002000
INT_RAM : 0x0000D000
EXT_RAM : 0x00400000

File_Info   : FISE61D_11C_PCB01_gprs_MT6261_S00.MAUI_11C_W13_52_MP_V2_F9.bin
FileVersion : MAUI.11C.W13.52.MP.V2.F9
Flash now

Erase region , wait ...
Write data , wait ...
Write : I10 VGOTEL FISE61D_11C_PCB01_GPRS_MT6261_S00.MAUI_11C_W13_52_MP_V2_F9

Done!
Elapsed: 00:00:39
Reconnect Power/Cable!

 

[maanarman]

Qmobile E4 Write Flash Done

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 6 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0000
BB_CPU_SN : C71C25821522606A4D0C425AB6A937FE
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
InitRes : 00000000
DEV[0] : EF00 4000 1600 0000
DEV[1] : 0000 0000 0000 0000
DA_INFO   : 0xC0 , Ver : 3.2 , BBID : 0x88
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
INT_RAM : 0x0000D400
EXT_RAM : 0x00400000

File_Info   : WBG1307QM_0202_PCB01_gprs_MT6250_S00.1307QM_0202_V0766.bin
FileVersion : 1307QM_0202_V0766

Done!
Elapsed: 00:00:13
Reconnect Power/Cable!


Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 6 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0000
BB_CPU_SN : C71C25821522606A4D0C425AB6A937FE
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
InitRes : 00000000
DEV[0] : EF00 4000 1600 0000
DEV[1] : 0000 0000 0000 0000
DA_INFO   : 0xC0 , Ver : 3.2 , BBID : 0x88
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
INT_RAM : 0x0000D400
EXT_RAM : 0x00400000

Backup done
Executing FFS FORMAT now...
FAT_RANGE : 0x003B5000-0x003FFFFF , LEN : 0x0004B000
DA_RET   : DA_IN_PROGRESS
DA_RET   : FORMAT_DONE

Done!
Elapsed: 00:00:17
Reconnect Power/Cable!


Operation : Read Flash [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 6 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0000
BB_CPU_SN : C71C25821522606A4D0C425AB6A937FE
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
InitRes : 00000000
DEV[0] : EF00 4000 1600 0000
DEV[1] : 0000 0000 0000 0000
DA_INFO   : 0xC0 , Ver : 3.2 , BBID : 0x88
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
INT_RAM : 0x0000D400
EXT_RAM : 0x00400000
Reading Flash Content now ...

Read Flash now
Read Ok , 4194304 bytes read
Check and collect compile info
File_Info   : WBG1307QM_0202_PCB01_gprs_MT6250_S00.1307QM_0202_V0766.bin
FileVersion : 1307QM_0202_V0766
Saved to : C:\InfinityBox\CM2MTK\Read_out\WBG1307QM_0202_PCB01_gprs_MT6250_S00.1307QM_0202_V0766.bin

Done!
Elapsed: 00:00:28
Reconnect Power/Cable!


Load File
File_Info   : WBG1307QM_0202_PCB01_gprs_MT6250_S00.1307QM_0202_V0735.bin
FileVersion : 1307QM_0202_V0735
Load File Ok

Operation : Flash [ v1.58 ]

======= Flash
Files set for flashing :
[ MCU ] : E4 QMOBILE ALL LOCK OK WBG1307QM_0202_PCB01_GPRS_MT6250_S00.1307QM_0202_V0735

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 6 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0000
BB_CPU_SN : C71C25821522606A4D0C425AB6A937FE
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
InitRes : 00000000
DEV[0] : EF00 4000 1600 0000
DEV[1] : 0000 0000 0000 0000
DA_INFO   : 0xC0 , Ver : 3.2 , BBID : 0x88
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
INT_RAM : 0x0000D400
EXT_RAM : 0x00400000

File_Info   : WBG1307QM_0202_PCB01_gprs_MT6250_S00.1307QM_0202_V0735.bin
FileVersion : 1307QM_0202_V0735
Flash now

Erase region , wait ...
Write data , wait ...
Write : E4 QMOBILE ALL LOCK OK WBG1307QM_0202_PCB01_GPRS_MT6250_S00.1307QM_0202_V0735

Done!
Elapsed: 00:00:37
Reconnect Power/Cable!

 

[maanarman]

Moto E4 FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:01:00

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : perry_verizon_f
Model  : Moto E (4)
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:11

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:05

 

[maanarman]

Gfive U220+ Phone Lock Remove Done

Operation : Identify [ v1.03 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
BootSource  :  InternalLibrary
BootVersion : Infinity SCR SC6531E Loader v 1.2
Port speed : 921600
FDL Flash  : Control transfered!

Boot Done!

CS0_MEM : SPI : [WINBOND] : W25Q32 : 0x00400000 [ 4MiB ]

IMEI[1] : 869981029583417
IMEI[2] : 869981029654119

Done!
Elapsed: 00:00:12

Reconnect Power/Cable!

Operation : Format FileSystem [ v1.03 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
BootSource  :  InternalLibrary
BootVersion : Infinity SCR SC6531E Loader v 1.2
Port speed : 921600
FDL Flash  : Control transfered!

Boot Done!

CS0_MEM : SPI : [WINBOND] : W25Q32 : 0x00400000 [ 4MiB ]

Make backup of sensetive data
Backup saved to : C:\InfinityBox\CM2SCR\Backup\00400000_FMT_BACK_028E400CCA1D_NVM.nv

Executing FormatFFS ...
Format FFS Done!

Done!
Elapsed: 00:00:14

Reconnect Power/Cable!

 

[maanarman]

Qmobile X33 FRP Remove Done

Operation : Check/Read Info [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 73 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ...

Model Name  : QMobile_X33
Model Brand : QMobile
Model Device: QMobile_X33
AndrVersion : 6.0
BaseBand CPU: QMOBILE_X33
CompileDate : 7/24/2017 2:07:51 AM
Project Ver : MRA58K release-keys
Model Ext   : QMobile X33

ExtraInfo : HWInfo not exists, normal phone

Elapsed: 00:00:19

Reconnect Power/Cable!


Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 73 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size  : 0x000000012AAF7000
State : 0x0001

Mount : /cache
Size  : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x/6.x : Reset FRP Lock
Reset Ok!


Done!

Elapsed: 00:00:20

Reconnect Power/Cable!

 

[shahbazali]

 

[shahbazali]

Please login to view image

 

[shahbazali]

Please login to view image

 

[maanarman]

Qmobile Sms Not Sent Problem Done

Operation : Reset Settings [ v1.03 ]
----- > Powered On :
1. Power On device
2. Connect USB cable
3. When device show StorageMode : Press '0' button for a 5 second!
----- > Powered Off :
1. Insert USB cable
2. Wait when device show Charge icon
3. When device show StorageMode : Press '0' button for a 5 second!

Wait for device ...

Device Connected!
BOOT_PWR0 : 0x00600000
BOOT_INIT : 0x81C0024C
BOOT_MODE : DOWNLOAD
BOOT_INTV : 6533G-FPTRUNK-W16.44.2
InternalVersion: g8bec5c4c
Setting BOOTROM mode
BOOT_MODE : BOOTROM
Boot_CPU  : 0x08090007 : [SPREADTRUM] : SC6533G
MEMD for flsh_spi32m Branch: none
Boot_CS0 : 0x00000000 : SPI : [SPIDEF] : 25Q32 : 0x00400000 [ 4MiB ]
Performing MemoryInit
Selecting RL
Sending RL
Config : MemoryInit
Config : Loader
BOOT_MODE : RLOADER
Boot IV  : 0xFBA2A250
Boot done!

Preparing PMT
Verifying PMT
Erasing 1474560 bytes

FileSystem format done!


Done!
Elapsed: 00:00:29

Reconnect Power/Cable!

 

[maanarman]

Qmobile i7i Pro Remove Pattern And FRP Done

Set mode to : SP [SC773x] eMMC [Android 6.x]

Operation : Check/Read Info [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ...

Model Name  : i7i_PRO
Model Brand : QMobile
Model Device: i7i_PRO
AndrVersion : 6.0
BaseBand CPU: SP7731CEA
CompileDate : 3/20/2017 10:17:49 AM
Project Ver : QMobile i7i PRO_MP_20_03
Model Ext   : QMobile i7i PRO

ExtraInfo : HWInfo not exists, normal phone

Elapsed: 00:00:17

Reconnect Power/Cable!


Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size  : 0x0000000113EF7000
State : 0x0001

Mount : /cache
Size  : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x/6.x : Reset FRP Lock
Reset Ok!


Done!

Elapsed: 00:00:20

Reconnect Power/Cable!

 

[maanarman]

China Nokia 220 Remove Locks Done

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Verify data... Can take some time
Init Ok, formatting DIN area ...
Format Block Done!
Done!

Elapsed: 00:00:09

Reconnect Power/Cable!

 

[maanarman]

Moto E4 FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1766
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1766
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1766
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:00:59

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : sperry_sprint
Model  : Moto E (4)
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:38

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:07

 

[maanarman]

Corn 3310 Remove Locks Done

Operation : Reset Settings [ v1.03 ]
----- > Powered On :
1. Power On device
2. Connect USB cable
3. When device show StorageMode : Press '0' button for a 5 second!
----- > Powered Off :
1. Insert USB cable
2. Wait when device show Charge icon
3. When device show StorageMode : Press '0' button for a 5 second!

Wait for device ...

Device Connected!
BOOT_PWR0 : 0x00600000
BOOT_INIT : 0x81C0024C
BOOT_MODE : DOWNLOAD
BOOT_INTV : 6533G-FPTRUNK-W16.44.2
InternalVersion: g8bec5c4c
Setting BOOTROM mode
BOOT_MODE : BOOTROM
Boot_CPU  : 0x08090007 : [SPREADTRUM] : SC6533G
MEMD for flsh_spi32m Branch: none
Boot_CS0 : 0x00000000 : SPI : [SPIDEF] : 25Q32 : 0x00400000 [ 4MiB ]
Performing MemoryInit
Selecting RL
Sending RL
Config : MemoryInit
Config : Loader
BOOT_MODE : RLOADER
Boot IV  : 0xFBA2A250
Boot done!

Preparing PMT
Verifying PMT
Erasing 1474560 bytes

FileSystem format done!


Done!
Elapsed: 00:00:25

Reconnect Power/Cable!