★★ Post Here All Successful Stories By Infinity-Box CM/CM2- ★★

[maanarman]

SAMSUNG G935T FLASH DONE

Port open Ok!
LOKE received!
Prepare Ok!
Enter Setup...
Setup Done!
Try download PIT...
Download PIT Ok!
Start flashing!

Flashing emmc_appsboot.mbn
Flashing lksecapp.mbn
Flashing xbl.elf
Flashing tz.mbn
Flashing hyp.mbn
Flashing devcfg.mbn
Flashing pmic.elf
Flashing rpm.mbn
Flashing cmnlib.mbn
Flashing keymaster.mbn
Flashing apdp.mbn
Flashing msadp.mbn
Flashing cmnlib64.mbn
Flashing sec.dat
Flashing NON-HLOS.bin
Flashing boot.img
Flashing recovery.img
Flashing system.img.ext4
Flashing persist.img.ext4
Flashing modem.bin
Flashing adspso.bin
Flashing done

Reboot phone...


Phone Disconnected

 

[maanarman]

QMOBILE I6I FRP REMOVE DONE

Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 150100464A32374D4202F9C79AC8430F
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM72J
[eMMC] : FLASH_CID : 150100464A32374D4202F9C79AC8430F
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID    : 0x644765A71E1475F0BE798F3EB3F2A4F6
INT RAM    : 0x00020000
EXT RAM    : 0x30000000 [768 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!

Done!
Elapsed: 00:00:07
Reconnect Power/Cable!

 

[maanarman]

KECHAODA K6 HANG LOGO DONE

SCRD mode : AUTO
SPRD mode : SC6530 : REV : 0000 : NOR


SPRD mode : SC6531 : REV : E000 : NOR

Operation : Identify [ v1.02 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
BootSource  :  InternalLibrary
BootVersion : Infinity SCR SC6531E Loader v 1.2
Port speed : 921600
FDL Flash  : Control transfered!

Boot Done!

CS0_MEM : SPI : [WINBOND] : W25Q32 : 0x00400000 [ 4MiB ]

IMEI[1] : 864580032987469
IMEI[2] : 864580032987477

Done!
Elapsed: 00:00:11

Reconnect Power/Cable!

Operation : Format FileSystem [ v1.02 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
BootSource  :  InternalLibrary
BootVersion : Infinity SCR SC6531E Loader v 1.2
Port speed : 921600
FDL Flash  : Control transfered!

Boot Done!

CS0_MEM : SPI : [WINBOND] : W25Q32 : 0x00400000 [ 4MiB ]

Make backup of sensetive data
Backup saved to : C:\InfinityBox\CM2SCR\Backup\00400000_FMT_BACK_1C92A1B204EE_NVM.nv

Executing FormatFFS ...
Format FFS Done!

Done!
Elapsed: 00:00:13

Reconnect Power/Cable!

 

[maanarman]

VGOTEL OCEAN 6 FRP REMOVE DONE

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 14 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v1.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size  : 0x00000000FBAF7000
State : 0x0001

Mount : /cache
Size  : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x/6.x : Reset FRP Lock
Reset Ok!


Done!

Elapsed: 00:00:26

Reconnect Power/Cable!

 

[maanarman]

ITEL S12 READ FF DONE

Operation : Read Flash [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 150100464E36324D4203759CCE91B453
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM26N
[eMMC] : FLASH_CID : 150100464E36324D4203759CCE91B453
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0x644765A7BAC83C42095BBAD38EA58B74
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Content now ...

xGPT : Normalize settings Ok!

Brand     : Itel
ProdName  : I805
ProdModel : itel S12
Device    : itel-S12
AndroidVer: 7.0
MTKxCPU   : MT6580
MTKxPRJ   : S12-I805-7.0-OP-V048-20180419

[Read Ok] : preloader_s12.bin
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : logo.bin
[Read Ok] : tz1.img
[Read Ok] : tz2.img
[Read Ok] : secro.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img

[ScatCFG] : MT6580 / V1.1.2 / s12 / EMMC
Android Info saved
HWConfig Info saved
FW Size : 3368 MiB
Scatter saved to : C:\Users\test\Desktop\TEMP\MT6580__Itel__itel_S12__itel-S12__7.0__S12-I805-7.0-OP-V048-20180419\

All done!

Done!
Elapsed: 00:13:20
Reconnect Power/Cable!

 

[maanarman]

SAMSUNG J3 READ PAC FILE DONE

Operation : Read FullFlash [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!

[FW_READER] : Prepare Ok!
- > Wait phone connected ...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

- > Wait phone connected ...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Model Name  : J3
Model Brand : J3
Model Device: J3
AndrVersion : 6.0
BaseBand CPU: SP7731CEB
Project Ver : MRA58K release-keys
Model Ext   : J3

[Read Mode] : HSUSB : 0x3000

[FW_READER] : Reading Firmware Now ...

[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731C_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_Trunk_W16.28.5_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_540x960.bin
Skip [EMP] : FBOOTLOGO
[Read Ok] : boot.img
[Read Ok] : system.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Read Ok] : sysinfo.img
[Build Ok] : userdata.img

AndroidInfo created
Firmware Size : 1582 MiB
Saved to : C:\Users\test\Desktop\TEMP\SP7731CEB_J3_6.0_MRA58K_release-keys_J3\
Done!

Elapsed: 00:09:30

Reconnect Power/Cable!

 

[maanarman]

QMOBILE S2 FRP REMOVE DONE

Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 9 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A483847316505073459C564C2E1
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e1G8
[eMMC] : FLASH_CID : 90014A483847316505073459C564C2E1
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0x42F12DCD402B99DE842A2E698D444921
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!
Clear DIN
Clear Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:42
Reconnect Power/Cable!

 

[maanarman]

Motorola Turbo Frp Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:01:37

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : quark_verizon
Model  : XT1254
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:14

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:06

 

[maanarman]

Motorola E4 FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:01:02

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : perry_verizon_f
Model  : Moto E (4)
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:12

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:06

 

[maanarman]

Qmobile i8i FRP Remove Done

Set mode to : SP [SC773x] eMMC [Android 6.x]

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size  : 0x0000000133CF7000
State : 0x0001

Mount : /cache
Size  : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x/6.x : Reset FRP Lock
Reset Ok!


Done!

Elapsed: 00:00:19

Reconnect Power/Cable!

 

[maanarman]

Motorola Turbo FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:02:02

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : quark_verizon
Model  : XT1254
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:12

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:05

 

[maanarman]

Oale X1 Factory Reset Done

Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 8801034550423130303974BB000083A3
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x88 , OEM : 0103
[eMMC] : FLASH_INF : [FORESEE] , 001BP
[eMMC] : FLASH_CID : 8801034550423130303974BB000083A3
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001CE100000
[eMMC] : FLASH_UCP : 7393 MiB [eMMC 8 GiB]
DEV RID    : 0x644765A7337EA7DEB6048CC0CE3C37FB
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!
Clear DIN
Clear Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:49
Reconnect Power/Cable!

 

[maanarman]

QMOBILE I6 METAL ONE WRITE PAC DONE

Set mode to : SP [SC773x] eMMC [Android 6.x]

Infinity SC Firmware Detected
FW Size : 2874 MiB
Load Ok!

File Info
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand   : QMobile
Device Model   : i6_Metal_ONE_new
Device CPU     : i6_Metal_ONE
Device IntName : i6_Metal_ONE
Device Version : 6.0
Device Compile : 12/15/2016 10:31:38 AM
Device Project : MRA58K release-keys
Device ExtInfo : QMobile i6 Metal ONE


Operation : Flash [ v1.27 ]

======= Flash
Files set for flashing :
[ MCU ] : SC77xx Infinity Package

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!

PMTManager : Load 0x19 records
PMTManager : PMT Update Ok!
Flashing now

Update BootCode : u-boot-spl-16k.bin
Write Data ...
Write Data Ok!

Update BootCode : u-boot.bin
Erase block ...
Block erase Ok!
Write Data ...
Write Data Ok!

Write FSImage : prodnv.img
Write Data ...
Write Data Ok!

Write CodeData : sc7731C_CP0_modem.bin
Write Data ...
Write Data Ok!

Write CodeData : DSP_DM_Gx.bin
Write Data ...
Write Data Ok!

Erase Block : RuntimeData
Erase block ...
Block erase Ok!

Write CodeData : sc8830g_modem_CP2_WCN_Trunk_W16.28.5_Release.bin
Write Data ...
Write Data Ok!

Erase Block : RuntimeData
Erase block ...
Block erase Ok!

Write CodeData : logo_480x854.bin
Write Data ...
Write Data Ok!

Write CodeData : fblogo_480x854.bin
Write Data ...
Write Data Ok!

Write CodeData : boot.img
Write Data ...
Write Data Ok!

Write FSImage : system.img
Write Data ...
Write Data Ok!

Erase Block : PERSIST
Erase block ...
Block erase Ok!

Write CodeData : sysinfo.img
Write Data ...
Write Data Ok!

Write FSImage : cache.img
Write Data ...
Write Data Ok!

Write CodeData : recovery.img
Write Data ...
Write Data Ok!

Erase Block : MISC
Erase block ...
Block erase Ok!

Write FSImage : userdata.img
Write Data ...
Write Data Ok!


Elapsed: 00:15:59

Reconnect Power/Cable!

 

[maanarman]

Kechaoda K6 Read Flash Done

Operation : Read Flash [ v1.02 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
BootSource  :  InternalLibrary
BootVersion : Infinity SCR SC6531E Loader v 1.2
Port speed : 921600
FDL Flash  : Control transfered!

Boot Done!

CS0_MEM : SPI : [WINBOND] : W25Q32 : 0x00400000 [ 4MiB ]

Read Ok!

Saved to : C:\Users\test\Desktop\FLASH_DUMP.bin

Done!
Elapsed: 00:00:41

Reconnect Power/Cable!

 

[maanarman]

Samsung G935t Flash Done

Port open Ok!
LOKE received!
Prepare Ok!
Enter Setup...
Setup Done!
Try download PIT...
Download PIT Ok!
Start flashing!

Flashing emmc_appsboot.mbn
Flashing lksecapp.mbn
Flashing xbl.elf
Flashing tz.mbn
Flashing hyp.mbn
Flashing devcfg.mbn
Flashing pmic.elf
Flashing rpm.mbn
Flashing cmnlib.mbn
Flashing keymaster.mbn
Flashing apdp.mbn
Flashing msadp.mbn
Flashing cmnlib64.mbn
Flashing sec.dat
Flashing NON-HLOS.bin
Flashing boot.img
Flashing recovery.img
Flashing system.img.ext4
Flashing persist.img.ext4
Flashing modem.bin
Flashing adspso.bin
Flashing cache.img.ext4
Flashing done

Reboot phone...


Phone Disconnected

Phone found on COM759

Phone In Download mode...

 

[maanarman]

Samsung G930t Write Flash Done

Port open Ok!
LOKE received!
Prepare Ok!
Enter Setup...
Setup Done!
Try download PIT...
Download PIT Ok!
Start flashing!

Flashing emmc_appsboot.mbn
Flashing lksecapp.mbn
Flashing xbl.elf
Flashing tz.mbn
Flashing hyp.mbn
Flashing devcfg.mbn
Flashing pmic.elf
Flashing rpm.mbn
Flashing cmnlib.mbn
Flashing keymaster.mbn
Flashing apdp.mbn
Flashing msadp.mbn
Flashing cmnlib64.mbn
Flashing sec.dat
Flashing NON-HLOS.bin
Flashing boot.img
Flashing recovery.img
Flashing system.img.ext4
Flashing persist.img.ext4
Flashing modem.bin
Flashing adspso.bin
Flashing cache.img.ext4
Flashing done

Reboot phone...


Phone Disconnected

 

[maanarman]

Lg D858hk Remove Locks Done

Operation : Identify [ v1.03 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD VOLUME UP KEY!
3. Insert USB cable, wait until Download mode screen will appear

Wait for phone...
Connection opened successfully!
Waiting for loader ...
Handshake passed!
Collect info...

Running : MiniOS 3.0 , ver.1.1 , with proto ver.01000004
HWInfo  : BaseBand : MSM8974
HWInfo  : ChargeLv : 5%
HWInfo  : MEM_INFO : 032GE4 , MEM_LEN : 0x03A3E000 [eMMC 32 GiB]
DevInfo : Model : LG-D858HK , Type : D858HK30b
DevInfo : ANDROID 6.0
DevInfo :   PSN : SM08S141121001161 , PID : LGD858HK119aeb8d
DevInfo : IMEI  : 355875060327935
DevInfo : SecMode : S , Build : U , RCT : 000F4240
SWInfo  : SWver : V30b , SW : LGD858HKAT-00-V30b-HKG-XX-SEP-06-2016-32G+0
SWInfo  : FacSW : LGD858HKAT-00-V30b-HKG-XX-SEP-06-2016-32G+0
RegInfo : Region : HK , Provider : OPEN

Prepare passed, mode 0x01
Boot done!


Brand     : lge
ProdName  : g3_open_hk
ProdModel : LG-D858HK
Device    : g3
AndroidVer: 6.0
SWVersion : LGD858HKAT-00-V30b-HKG-XX-SEP-06-2016+0
Manufact. : LGE
LGMxCPU   : MSM8974

Done!
Elapsed: 00:00:08

Operation : Reset Settings/Format FS [ v1.03 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD VOLUME UP KEY!
3. Insert USB cable, wait until Download mode screen will appear

Wait for phone...
Connection opened successfully!
Waiting for loader ...
Handshake passed!
Collect info...
Prepare passed, mode 0x01
Boot done!

Format UserData
Format Cache
Format done

Reconnect Power/Cable!

Done!
Elapsed: 00:00:12

 

[maanarman]

Samsung j327vpp Write Flash Done

Port open Ok!
LOKE received!
Prepare Ok!
Enter Setup...
Setup Done!
Try download PIT...
Download PIT Ok!
Start flashing!

Flashing aboot.mbn
Flashing sbl1.mbn
Flashing rpm.mbn
Flashing tz.mbn
Flashing devcfg.mbn
Flashing NON-HLOS.bin
Flashing cmnlib.mbn
Flashing keymaster.mbn
Flashing lksecapp.mbn
Flashing sec.dat
Flashing apdp.mbn
Flashing msadp.mbn
Flashing boot.img
Flashing recovery.img
Flashing system.img.ext4
Flashing persist.img.ext4
Flashing userdata.img.ext4
Flashing modem.bin
Flashing adspso.bin
Flashing cache.img.ext4
Flashing done

Reboot phone...


Phone Disconnected

 

[maanarman]

Qmobile Factory Reset Done

Set mode to : SPD6531

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Verify data... Can take some time
Init Ok, formatting DIN area ...
Format Block Done!
Done!

Elapsed: 00:00:09

Reconnect Power/Cable!

 

[maanarman]

vgotel i classic remove locks done

SPRD mode : SC6531 : REV : C000 : NOR

Operation : Format FileSystem [ v1.02 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
BootSource  :  InternalLibrary
BootVersion : Spreadtrum Boot Block version 1.2
Port speed : 921600
FDL Flash  : Control transfered!

Boot Done!

CS0_MEM : SPI : [FIDELIX] : FM25Q64 : 0x00800000 [ 8MiB ]

Make backup of sensetive data
Backup saved to : C:\InfinityBox\CM2SCR\Backup\00800000_FMT_BACK_0970F103D455_NVM.nv

Executing FormatFFS ...
Format FFS Done!

Done!
Elapsed: 00:00:20

Reconnect Power/Cable!