Post Success Reports Here Successfully Repaired/Dead Recovered Handset By Ufi Box
- Thread starter Deepesh Sharma
- Start date
Dr.sunilsingh
Friend's Martview
REALME 2 PRO ( RMX1801EX ) User lock + Dump Backup
Without Any Risk Of Stuck On Logo All Job Successfully Done Ufi-Box Only
RECOVER HANDSET SUCCESSFULLY ALIVE BY Dr.Research-Center-Team
Without Any Risk Of Stuck On Logo All Job Successfully Done Ufi-Box Only
RECOVER HANDSET SUCCESSFULLY ALIVE BY Dr.Research-Center-Team
Meizu M1 metal userlock reset done
Software engineer tied up DA bring it to my table
Software engineer tied up DA bring it to my table
ferouzkassim
Active Member
OPPPO F11 PRO PASSWORD REMOVE DONE
Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8840-4224
Boot version: 1.04, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Bus: 1 bit (SDR 48MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: hDEaP3 (0x684445615033), rev: 0x03, serial number: 0x3B67B581
Manufacturing date: Mar 2019
CID: 90014A68 44456150 33033B67 B5813618
CSD: D0270032 8F5903FF FFFFFFEF 8E400042
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 16384 KiB
User area: 116.48 GiB(125,074,145,280 bytes)
Cache size: 2 MiB
Hardware reset function: 1
Partition configuration: 0x48
Boot acknowledge is sent during the boot operation
Boot partition 1 is enabled for boot
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x02
Bus width: x8 (sdr/ddr), boot mode: sdr(default), reset bus width to x1 sdr(default)
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked
EXT_CSD backup saved to "\\%BACKUPS%\hDEaP3_3B67B581.ext_csd"
ANDROID System Info:
platform: MT6771, cpu abi: arm64-v8a
manufacturer: OPPO
board: oppo6771_18531, name: CPH1969
brand: OPPO, model: CPH1969 (OPPO F11 Pro)
build model list: CPH1985 (OPPO R15), CPH1987 (OPPO F11 Pro), CPH1969 (OPPO F11 Pro)
build id: PPR1.180610.011, version: 9 Pie (CPH1969EX_11_A.38)
build description: full_oppo6771_18531-user 9 PPR1.180610.011 eng.root.20191024.232120 release-keys
crypto state: encrypted?
crypto state: encrypted?
Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8840-4224
Boot version: 1.04, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Bus: 1 bit (SDR 48MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: hDEaP3 (0x684445615033), rev: 0x03, serial number: 0x3B67B581
Manufacturing date: Mar 2019
CID: 90014A68 44456150 33033B67 B5813618
CSD: D0270032 8F5903FF FFFFFFEF 8E400042
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 16384 KiB
User area: 116.48 GiB(125,074,145,280 bytes)
[Oppo] MasterClear [2]... Done
Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8840-4224
Boot version: 1.04, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Bus: 1 bit (SDR 48MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: hDEaP3 (0x684445615033), rev: 0x03, serial number: 0x3B67B581
Manufacturing date: Mar 2019
CID: 90014A68 44456150 33033B67 B5813618
CSD: D0270032 8F5903FF FFFFFFEF 8E400042
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 16384 KiB
User area: 116.48 GiB(125,074,145,280 bytes)
Cache size: 2 MiB
Hardware reset function: 1
Partition configuration: 0x48
Boot acknowledge is sent during the boot operation
Boot partition 1 is enabled for boot
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x02
Bus width: x8 (sdr/ddr), boot mode: sdr(default), reset bus width to x1 sdr(default)
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked
EXT_CSD backup saved to "\\%BACKUPS%\hDEaP3_3B67B581.ext_csd"
ANDROID System Info:
platform: MT6771, cpu abi: arm64-v8a
manufacturer: OPPO
board: oppo6771_18531, name: CPH1969
brand: OPPO, model: CPH1969 (OPPO F11 Pro)
build model list: CPH1985 (OPPO R15), CPH1987 (OPPO F11 Pro), CPH1969 (OPPO F11 Pro)
build id: PPR1.180610.011, version: 9 Pie (CPH1969EX_11_A.38)
build description: full_oppo6771_18531-user 9 PPR1.180610.011 eng.root.20191024.232120 release-keys
crypto state: encrypted?
crypto state: encrypted?
Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8840-4224
Boot version: 1.04, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Bus: 1 bit (SDR 48MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: hDEaP3 (0x684445615033), rev: 0x03, serial number: 0x3B67B581
Manufacturing date: Mar 2019
CID: 90014A68 44456150 33033B67 B5813618
CSD: D0270032 8F5903FF FFFFFFEF 8E400042
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 16384 KiB
User area: 116.48 GiB(125,074,145,280 bytes)
[Oppo] MasterClear [2]... Done
Itel A32F MTK port only recover
Samsung A2Core (A260G) Dead Dropped Case Make DEad Port Exynos Only
Pasted Emmc Successfully Removed N Reprogramed And Set Recover Done By Ufi-Box
Image Dead Port
Image-1
Ufi-log
Set Now Recovered Go To Download Mode
Pasted Emmc Successfully Removed N Reprogramed And Set Recover Done By Ufi-Box
Image Dead Port
Image-1
Ufi-log
Set Now Recovered Go To Download Mode
Dr.sunilsingh
Friend's Martview
OPPO 11 PRO ( CPH1969EX ) User lock + Dump Backup
Without Any Risk Of Stuck On Logo All Job Successfully Done Ufi-Box Only
RECOVER HANDSET SUCCESSFULLY ALIVE BY Dr.Research-Center-Team
Without Any Risk Of Stuck On Logo All Job Successfully Done Ufi-Box Only
RECOVER HANDSET SUCCESSFULLY ALIVE BY Dr.Research-Center-Team
gsmshimul
Active Member
- Dec 26, 2018
- 18
- 12
Symphony v52 dead recovery done by UFI Box & baseband unknown repair
Attachments
-
Screenshot_5.png
ram-64 or 128gOPPO 11 PRO ( CPH1969EX ) User lock + Dump Backup
Without Any Risk Of Stuck On Logo All Job Successfully Done Ufi-Box Only
RECOVER HANDSET SUCCESSFULLY ALIVE BY Dr.Research-Center-Team
Realme C2 Rmx1941 Remove Userlock+Frp Lock Without Lost Any Media
All Job Successfully Done With Ufi-Box
Image
Remove Lock
Remove Frp
All Job Successfully Done
All Job Successfully Done With Ufi-Box
Image
Remove Lock
Remove Frp
All Job Successfully Done
bro idont have any backp after cange emme unknow basbandSamsung J2 (j200G)Dead Recover Replace EmmcAnd Reprogram With Ufi-Box
Image 1(Make 1Jumper Under Emmc)
Ufi-log 1
Ufi-Log2
Successfully Alive Handset
i tried all method write efs nv cert but reault same
vishal3008N
Product Supporter
Mi Note 5 pro Hang On Logo Flashing Failed Sucessfully Recover Done.
Attachments
-
IMG_20191213_165707.jpg -
IMG_20191213_143413.jpg -
IMG_20191213_165718__01__01.jpg -
IMG_20191213_170227__01__01.jpg -
IMG_20191213_171723__01__01.jpg -
IMG_20191213_172950.jpg -
IMG_20191213_190305.jpg
Last edited:
can you upload your back up file here sir?OPPO F7 ( CPH1819EX ) WITHOUT ONLINE FLASH | OPPO F7 CPH1819 - ISP PINOUT / AFTER DEADBOOT / EMMC REPAIRE
OPPO F7 ( CPH1819EX ) DEAD HANDSET ( Other Shop Return ) Successfully By UFI BOX
Dr.Research-Center-Team
OPPO F11 ( CPH1911 ) Dead Handset ( Other Shop Return ) Successfully By UFI BOX
Dr.Research-Center-Team
if it is cph1911 then in brand colom of ufi i see cph1803 why ?
mine still dead cph1911 set came with lock
did factory reset and got error and set dead
then write ext csd still dead please help
Oppo A5 2020 without DATA LOSE REMOVE PATTERN CODE Successfully Done. Ufi BOX
https://www.facebook.com/photo.php?...S41TUQMoo3F3xWEJaRw0Tr5gEICgWgechNfDGC-ilz-bJ
https://www.facebook.com/photo.php?...S41TUQMoo3F3xWEJaRw0Tr5gEICgWgechNfDGC-ilz-bJ
Hassani143143
Junior Member
Bro You Have oppo r15 Chinese model paam00 Dump file plz help me I need dump file