Q mobile i5 after flash dead

[khadim0313]

Q mobile i5 dead after flash with cm2 ..when i check info it gives error erased or damaged phone?? Any one have solution..

 

[Rizwan ch08]

Bro sand me cm2 read logo


Sent from my iPhone using GsmMarhaba

 

[khadim0313]

Dear

Bro sand me cm2 read logo


Sent from my iPhone using GsmMarhaba

bro ihave cm2 miracle box ihave tried all flashing ..flashing done but not on

 

[khadim0313]

Card found : S/N : B74B1AF6 , v0134
Chinese Miracle II [MTK module] v 1.58
Operation : Check / Read Info [ v1.58 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 20 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164040502A2A5F8224B
Initialize Memory ...
[DA_ERROR] : DRAM Configure failed!
ErroCode : 0xBF0B0000
EMICFG_RET_FAILED
CodeDefine : DA_DRAMC_RANK1_CALIBRATION_FAILED
Boot Error!
Operation Failed
Elapsed: 00:00:44
Reconnect Power/Cable!

User selected Preloader file : preloader_s4700.bin
Operation : Init Preloader [ v1.58 ]
Supported HW by Preloader :
FlashID [0] CID : 90014A483447316404 , Name : H4G1d , Vendor : 90 , [HYNIX]
FlashID [1] CID : 110100303034473930 , Name : 004G90 , Vendor : 11 , [TOSHIBA]
FlashID [2] CID : 90014A483847326404 , Name : H8G2d , Vendor : 90 , [HYNIX]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Device boot not done
Check Drivers
Try again
Boot Error!
Operation Failed
Elapsed: 00:00:27
Reconnect Power/Cable!

User selected Preloader file : preloader_s4700.bin
Operation : Init Preloader [ v1.58 ]
Supported HW by Preloader :
FlashID [0] CID : 90014A483447316404 , Name : H4G1d , Vendor : 90 , [HYNIX]
FlashID [1] CID : 110100303034473930 , Name : 004G90 , Vendor : 11 , [TOSHIBA]
FlashID [2] CID : 90014A483847326404 , Name : H8G2d , Vendor : 90 , [HYNIX]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Device boot not done
Check Drivers
Try again
Boot Error!
Operation Failed
Elapsed: 00:00:27
Reconnect Power/Cable!

User selected Preloader file : preloader_s4700.bin
Operation : Init Preloader [ v1.58 ]
Supported HW by Preloader :
FlashID [0] CID : 90014A483447316404 , Name : H4G1d , Vendor : 90 , [HYNIX]
FlashID [1] CID : 110100303034473930 , Name : 004G90 , Vendor : 11 , [TOSHIBA]
FlashID [2] CID : 90014A483847326404 , Name : H8G2d , Vendor : 90 , [HYNIX]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 20 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164040502A2A5F8224B
Initialize Memory ...
DRAM configured from ScatFW!
DRAM initialize passed!
DRAM size : 0x20000000
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164040502A2A5F8224B
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID : 0xCF1D2EE434E6A8B2A05E1D14816B9B6A
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
SecCfg Passed , 1799
BL : BBID supported by BootLoader!
Supported HW by Preloader :
FlashID [0] CID : 90014A483447316404 , Name : H4G1d , Vendor : 90 , [HYNIX]
FlashID [1] CID : 110100303034473930 , Name : 004G90 , Vendor : 11 , [TOSHIBA]
FlashID [2] CID : 90014A483847326404 , Name : H8G2d , Vendor : 90 , [HYNIX]
BL : Storage supported by BootLoader!
Sending BootLoader ...
Preloader Sent , Init passed
SecCfg Passed , 1799
PartTable Init Failed, Reflashing required!
All Done
Done!
Elapsed: 00:00:11
Reconnect Power/Cable!

Operation : Check / Read Info [ v1.58 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 8 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164040502A2A5F8224B
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164040502A2A5F8224B
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID : 0xCF1D2EE434E6A8B2A05E1D14816B9B6A
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Info read not done Erased/damaged phone?
Done!
Elapsed: 00:00:07
Reconnect Power/Cable!

 

[Rizwan ch08]

brother try sptool ............

 

[kabzfredo]

whats did u use to flash coz thats nt a cm2 read data

Sent From Phantom6-Plus Using GsmMarhaba App

 

[khadim0313]

Bro i have tried sptool also flashing done but not on....
Ihave 2 files but no success

 

[kabzfredo]

do u hv nck?

Sent From Phantom6-Plus Using GsmMarhaba App

 

[kabzfredo]

if yes flash usimg nck and it i will auto boot after flashing

Sent From Phantom6-Plus Using GsmMarhaba App

 

[kabzfredo]

it once happened on me

Sent From Phantom6-Plus Using GsmMarhaba App

 

[khadim0313]

Emmc damaged ?? Or stilll any chance??

 

[qasimgsm]

Try bin file

Sent From SM-J500F Using GsmMarhaba App

 

[Urfi649]

Qmobile flash k bd dead hu gya hai. bohot files try kr chuka pr on ni hu rha flash hu jata hai lakin info read ni kr rha... plz help me...03135124817 irfan..

Chinese Miracle II [MTK module] v 1.58

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164040502A11BAB411D
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164040502A11BAB411D
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID : 0x1893739EC7082E751B4B7313F560F19A
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Info read not done Erased/damaged phone?

Done!
Elapsed: 00:00:09
Reconnect Power/Cable!

 

[arsallove]

brother is fault ka koi hall ni ha ma na bi boht try kya ha eras or damge error ka fault...

 

[GSM HELP]

Q mobile i5 dead after flash with cm2 ..when i check info it gives error erased or damaged phone?? Any one have solution..

Open Sp Tool Select I5 Fixed Firmware And Go Format Section

1 Auto Format Flash

2 Formate Whole Flash exceptbootloader

and Pres start button .

After Format Done

Reconnect Phone beatty and Data Cable again Flash
Your Problem solve Your dead Phone alive.

Flash File
I5 fixed - Download - 4shared

 

[Urfi649]

Ni bhai flash tu ho jata hai pr on ni hota.... stil prob

 

[softlinker]

bahi i have test file pls contact me skype

 

[naseeem]

Open Sp Tool Select I5 Fixed Firmware And Go Format Section

1 Auto Format Flash

2 Formate Whole Flash exceptbootloader

and Pres start button .

After Format Done

Reconnect Phone beatty and Data Cable again Flash
Your Problem solve Your dead Phone alive.

Flash File
I5 fixed - Download - 4shared

1000% done file after flash died thanx bro GOD BLESS U