OPPO A3S DEAD 9008 PORT RECOVERED SUCCESSFULLY.

[lacoste90]

sir help me please
my oppo cph1803 after factory reset by ufi via isp test point done, and after in the home screen, suddenly my phone brick 9008.

iim tired to flash oppo a3s and not happen for this device.

 

[pradip569]

oppo a3s 1803 lock after factory reset ufi box mobile phone works ok after 30 minutes later mobile restarting my phone dead only qualcomm 9008 port HELP ME

 

[maanarman]

Just Check CLK, CMD Resistor A3s 9008 Port only after ISP Points will be fixed.
Because of Sometimes it's Broken Due Soldering.

Thanks My problem Solved after fix CLK resistor

 

[moja3125]

Thanks My problem Solved after fix CLK resistor

Me also get the same problem can share how to fix it?

 

[maanarman]

Me also get the same problem can share how to fix it?

Just short CLK resistor Or replace
This resistor break

 

[Hanifmalaysiamari]

if a3s factory reset fail adjust clock 48 mhz and factory reset agaian then sucess

 

[royiks]

Just short CLK resistor Or replace
This resistor break

what is the value of the resistor in clk cmd

 

[bronce]

All Explained Write Dump File After NEed TO Reflash set, job done

after write dump how and what tool needed to reflash mate?

 

[reliableshop]

Just Check CLK, CMD Resistor A3s 9008 Port only after ISP Points will be fixed.
Because of Sometimes it's Broken Due Soldering.

I check all cmd, clk, data all ok After all done 9008 not solved

 

[reliableshop]

if a3s factory reset fail adjust clock 48 mhz and factory reset agaian then sucess

where is 48mhz clock? can you show me picture.

 

[reliableshop]

now done

 

[msibashankar]

what is the value of the resistor in clk cmd

1. CHEL WITH MULTI METER

CHEL CLK RESISTER OMS ---- 9K-10K OMS THEN ITS CORRECT

IF IT NOT CORRACT THEN REPLACE OTHER SET , OMS CHEK AND REAPLACE

CHEK CMD RESISTER OMS ------ 20-50OMS THEN ITSCC COOERCT

IF IT NOT CORRECT THEN U CAN JUMPER

 

[msibashankar]

1. CHEL WITH MULTI METER

CHEL CLK RESISTER OMS ---- 9K-10K OMS THEN ITS CORRECT

IF IT NOT CORRACT THEN REPLACE OTHER SET , OMS CHEK AND REAPLACE

CHEK CMD RESISTER OMS ------ 20-50OMS THEN ITSCC COOERCT

IF IT NOT CORRECT THEN U CAN JUMPER

HI FRIENDS SORRY FOR WRONG POST

CHEK WITH MULTIMETER

FOR CHEK CMD ITS RESISTER OMS--- 9K-10K CORRECT OMS

IF IT NOT REPALCE SAME 9K-10K RESISTER OTHER SETS

FOR CHEK CLK ITS RESISTER OMS --- 20-100 OMS ITS CORRECT

IF IT NOT CORRECT THEN U CAN JUMPER IT . NOT NEED REPLACE

 

[tejat901]

I have dump file
Tested dump file ufi box

 

[srkhan]

how to check the resistor cmd /clk??

first jumper the CLK then check power . if not ok than jumper cmd too

 

[Mohd faeem]

fix oppo dead after unlock set edl 9008

 

[Mohd faeem]

Oppo after unlocking set dead only edl 9008 Fix recover

 

[JOYMAAGSM]

OPPO A3S DUMP FILE

 

[usedmobilenpc]

1. CHEL WITH MULTI METER

CHEL CLK RESISTER OMS ---- 9K-10K OMS THEN ITS CORRECT

IF IT NOT CORRACT THEN REPLACE OTHER SET , OMS CHEK AND REAPLACE

CHEK CMD RESISTER OMS ------ 20-50OMS THEN ITSCC COOERCT

IF IT NOT CORRECT THEN U CAN JUMPER

hi, tks for sharing info about resistor, I want to know the capacitance value of the capacitor (VCCQ)? AND The one above it as Both this have been spoilt, and now my mobile stays in 9008 mode only!
and also in which part of the phone can I find the same value resistors and what is the exact value of the CMD reaistor?
wbr.

Sent from my SM-C7000 using Tapatalk

 

[atstech]

@All
no help or reply anyone?