HOT Tecno BF7 Frp One Click Without Credits / No Need Test Point TFM Tool

[Yeminoo]

Tecno BF7 Frp One Click Without Credits TFM Tool

-Open TFM MTK New Tool
-Choose Model
-Select Auth
-Click Frp Done

 

[kiberu]

DA SEND Error: 0x00007024 SECURE BOOT: SELECTED DA NOT SUPPORTED IN CURRENT DEVICE STATE!
PRELOADER Level: CORRECT DA required: PL/PL_CRYPTO/SWSEC
Connection fault
Disconnect battery and cable
- Check USB drivers
- Change cable - Change USB port - Do not use USB-hub
- Select another base|model|DA
- Try again
Reconnect Power/Cable now
pliz help here

 

[Yeminoo]

DA SEND Error: 0x00007024 SECURE BOOT: SELECTED DA NOT SUPPORTED IN CURRENT DEVICE STATE!
PRELOADER Level: CORRECT DA required: PL/PL_CRYPTO/SWSEC
Connection fault
Disconnect battery and cable
- Check USB drivers
- Change cable - Change USB port - Do not use USB-hub
- Select another base|model|DA
- Try again
Reconnect Power/Cable now
pliz help here

if not working with model...select mtk67xx v2 auth

 

[jadoon]

Selected model: Tecno BF7 (Tecno Spark Go 2023)
Operation: Repair
Software version: 6.9

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX or PC] in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM_V1632 (Android),usb2ser.sys,3.0.1504.0]
Device found at COM50 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0717
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0xE9EA04AB, 0x899422D4, 0xADF251EB, 0xCAE06B86
Load DownloadAgent... OK
Search DA... OK [1]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... error(STATUS_SEC_INVALID_DA_VER)

 

[Yeminoo]

Selected model: Tecno BF7 (Tecno Spark Go 2023)
Operation: Repair
Software version: 6.9

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX or PC] in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM_V1632 (Android),usb2ser.sys,3.0.1504.0]
Device found at COM50 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0717
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0xE9EA04AB, 0x899422D4, 0xADF251EB, 0xCAE06B86
Load DownloadAgent... OK
Search DA... OK [1]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... error(STATUS_SEC_INVALID_DA_VER)

Try To V2 Auth

 

[ahmijan1]

Jun 2024 Security Repair Imei Any Option With Tfm