Infinity vivo y73 after flesh set dead.any solution

[s.alam]

1. Power Off the device
2. Wait 20 seconds
3. Connect USB cable to device [remember Vol+ | Vol-]
Waiting for device connection...

PTFN: MediaTek USB Port_V1632 (COM6)
MODE: BOOTROM; PORT: 6
Waiting BOOT ack...
BROM: Skip ACK verify
BROM: Init BROM
BROM: Init passed
CHIP: MT6785 SBID: 0x8A00 HWVR: 0xCA00 SWVR: 0x0000 EVOL: 0x0000 HWC: 0x0813
CODE: Krug
TYPE: MODERN [RAPHAEL]
MEID: 002BF1DFEACB188884FF6A28284AE3E4
BROM: Sec Level: 0x000000E5 Mode: SBC+SDA+EXT
BROM: BROM|BL : 0x05|0xFE [BOOTROM]
BROM: SOCID: 36AECB594CB240EEC7158192E23DF12934E1868F0E17C7366FC349D44D8119F4
BROM: SLA: Local Auth
BROM: SLA: Starting Auth
BROM: FF : Look for EMI
BROM: FF : EMI not found
BROM: SLA: Auth Passed
BROM: SEC: 0x000000E0
AGENT: 0_base: BASE_v2112 | Manual: Off
[0656ff20] C:\InfinityBox\CM2MT2\boot\0_base\BASE_v2112\MTK_AllInOne_DA.bin
Looking for suitable BootChain in DA...
Found MT6785
AGENT: MTK_DOWNLOAD_AGENT
BROM: Sending 1st DA...
BROM: DA sent
BROM: Transfer control to DA...
DA: AGENT started
DA: SYNC with DA FAILED
Error: Fail to init protocol
Disconnect battery and cable
Check USB drivers - Change cable - Change USB port - Do not use USB-hub
Try again
Reconnect Power/Cable now

 

[Najmul007]

pm i can

 

[Infinity-Box]

1. Power Off the device
2. Wait 20 seconds
3. Connect USB cable to device [remember Vol+ | Vol-]
Waiting for device connection...

PTFN: MediaTek USB Port_V1632 (COM6)
MODE: BOOTROM; PORT: 6
Waiting BOOT ack...
BROM: Skip ACK verify
BROM: Init BROM
BROM: Init passed
CHIP: MT6785 SBID: 0x8A00 HWVR: 0xCA00 SWVR: 0x0000 EVOL: 0x0000 HWC: 0x0813
CODE: Krug
TYPE: MODERN [RAPHAEL]
MEID: 002BF1DFEACB188884FF6A28284AE3E4
BROM: Sec Level: 0x000000E5 Mode: SBC+SDA+EXT
BROM: BROM|BL : 0x05|0xFE [BOOTROM]
BROM: SOCID: 36AECB594CB240EEC7158192E23DF12934E1868F0E17C7366FC349D44D8119F4
BROM: SLA: Local Auth
BROM: SLA: Starting Auth
BROM: FF : Look for EMI
BROM: FF : EMI not found
BROM: SLA: Auth Passed
BROM: SEC: 0x000000E0
AGENT: 0_base: BASE_v2112 | Manual: Off
[0656ff20] C:\InfinityBox\CM2MT2\boot\0_base\BASE_v2112\MTK_AllInOne_DA.bin
Looking for suitable BootChain in DA...
Found MT6785
AGENT: MTK_DOWNLOAD_AGENT
BROM: Sending 1st DA...
BROM: DA sent
BROM: Transfer control to DA...
DA: AGENT started
DA: SYNC with DA FAILED
Error: Fail to init protocol
Disconnect battery and cable
Check USB drivers - Change cable - Change USB port - Do not use USB-hub
Try again
Reconnect Power/Cable now

it can not be dead because it was not connected at all

what is the problem with the phone?

 

[s.alam]

it can not be dead because it was not connected at all

what is the problem with the phone?

finger print not work.after letest ver flesh set dead

 

[Infinity-Box]

it can not be dead because it was not connected at all

give me flashing log text

 

[gsmstar]

Vivo Y73 Pattern Unlock For Unlock Tool After Death And Not showing Port, Remove EMMC After Repartion After Showing Port Next Spflash Tool Flash or Online Flash Work Done Mobile ready, Dont Format Unlock Tool..... easyjtag box use Format posible... thanks