UFi NOKIA 1.4 TA-1322 Dead after Factory Reset by UFIBOX

[NKhan_Gsm]

Hi I got a NOKIA 1.4 TA-1322 with pattern lock ,I solder according ISP pin out and did Factory Reset and Frp reset it was reseted but phone was hanging sometimes so I fully
reset from phone setting phone was fully charged after that phone is dead and only detecting in Qualcomm mode by PC so now UFI BOX cant detect it via ISP it gives Error,
How can solve this problem ?

WBR

Connection status: XHCI:HUB3[#3]:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8842-8253
Boot version: 1.05, FW version: 1.14 (Aug 25 2021 04:56:05)
Insertion test... Done
Init bus...
VCC: 3.0 V, VCCQ: 1.8 V
Failed to initialize eMMC (return code: 6, CMD Error: Invalid Voltage Range) !!!
CMD1 error, cmd response: 0x40FF8080, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Card might be DEAD, for moviNAND(Samsung) eMMC you may update the firmware with TestPoint ! ---

 

[aftab_ansari5287]

Hi I got a NOKIA 1.4 TA-1322 with pattern lock ,I solder according ISP pin out and did Factory Reset and Frp reset it was reseted but phone was hanging sometimes so I fully
reset from phone setting phone was fully charged after that phone is dead and only detecting in Qualcomm mode by PC so now UFI BOX cant detect it via ISP it gives Error,
How can solve this problem ?

WBR

First you try to flash from the edl port.
Clean the board then you connect the isp properly Then you take read info.

 

[dondav77]

ufibox is a killler tool only kills phone lol

 

[dondav77]

well i have gotten my experience , the bad experience all happens when you dont know how to use box ,tool isnt a killer tool box works very fine most of the dead device results from short clk filter or exdt config ..

 

[dimuthutec123]

Connection status: XHCI:HUB3[#4]:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8843-5539
Boot version: 1.05, FW version: 1.15 (Nov 8 2022 18:51:23)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x15 (Samsung)
Product name: GP6BAB (0x475036424142), rev: 0x05, serial number: 0xB235FED4
Manufacturing date: Jan 2021
CID: 15010047 50364241 4205B235 FED41822
CSD: D0270132 0F5903FF F6DBFFEF 8E40400C
Firmware version: 0x05
EXT_CSD revision: 1.8 (MMC v5.1)

 

[aftab_ansari5287]

Connection status: XHCI:HUB3[#4]:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8843-5539
Boot version: 1.05, FW version: 1.15 (Nov 8 2022 18:51:23)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x15 (Samsung)
Product name: GP6BAB (0x475036424142), rev: 0x05, serial number: 0xB235FED4
Manufacturing date: Jan 2021
CID: 15010047 50364241 4205B235 FED41822
CSD: D0270132 0F5903FF F6DBFFEF 8E40400C
Firmware version: 0x05
EXT_CSD revision: 1.8 (MMC v5.1)

Whta the Problem You Are Facing

 

[dondav77]

Plz check clk filter remove clk filter or make jumper

 

[Tahirshinwari]

Isp pinout
Google Image Result for https://lookaside.fbsbx.com/lookaside/crawler/media/?media_id=914468789459214