Z3X need help oppo f15 cph2001 dead after flash showing error ram 6

[makhdoom siddique]

need help oppo f15 cph2001 dead after flash showing error ram 6

Selected model: OPPO CPH2001 (Oppo F15)
Operation: Flash (Download only)
Software version: 3.5

Parse scatter file... OK
Load Rom Images... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM15 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xCE6B82EE, 0xDA4154D9, 0x1A0FC70D, 0x776677FF
Get Chip ID... [MT6765]
Get SOC ID... [B8C7E7395B888B09229C0710A5D3231D076B62F9B370F67FB29767960A714CEF]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A68444561503303007B3FAA78ED
Load EMI config from preloader... OK
Init EXT RAM... error(6)
Selected model: OPPO CPH2001 (Oppo F15)
Operation: Flash (Download only)
Software version: 3.5

Parse scatter file... OK
Load Rom Images... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM15 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xCE6B82EE, 0xDA4154D9, 0x1A0FC70D, 0x776677FF
Get Chip ID... [MT6765]
Get SOC ID... [B8C7E7395B888B09229C0710A5D3231D076B62F9B370F67FB29767960A714CEF]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A68444561503303007B3FAA78ED
Load EMI config from preloader... OK
Init EXT RAM... error(6)

 

[MiksaBB]

Selected model: OPPO CPH2269 (Oppo A16)
Operation: Format Flash
Software version: 3.8

This procedure will erase all flash and can damage your device.
Make sure that you have a backup created. Continue? YES
Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to BOX in BROM/PRELOADER Mode
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM10 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
oppo a16 cph2269 muerto

Detect chip [MT6765]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM10 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x21248AB3, 0xB8853613, 0xF810C789, 0xBE918E1E
Get Chip ID... [MT6765]
Get SOC ID... [3C22F44A8C2F72F48838B9518A7CE3E42F83AAE0223915F60B986E7C44F42447]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x15010044503644424202A10CCEE819F9
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... error(6)

 

[Najmul007]

gpt erase may be

 

[faizmalik]

Selected model: OPPO CPH2269 (Oppo A16)
Operation: Format Flash
Software version: 3.8

This procedure will erase all flash and can damage your device.
Make sure that you have a backup created. Continue? YES
Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to BOX in BROM/PRELOADER Mode
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM10 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
oppo a16 cph2269 muerto

Detect chip [MT6765]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM10 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x21248AB3, 0xB8853613, 0xF810C789, 0xBE918E1E
Get Chip ID... [MT6765]
Get SOC ID... [3C22F44A8C2F72F48838B9518A7CE3E42F83AAE0223915F60B986E7C44F42447]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x15010044503644424202A10CCEE819F9
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... error(6)

check health report with cm2 after cheaking if there is 90% cunsumed error then clear gpt partitin or there is no error of 90% then flash with cm2

 

[htenova]

Selected model: OPPO CPH2001 (OPPO F15)
Operation: Unlock bootloader
Software version: 7.5
Work ID: 45453106

Connect phone in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,usbser,MediaTek USB Port,usbser.sys,10.0.19041.3636]
You are using driver version 10.0.19041.3636, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM14 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,usbser,MediaTek USB Port,usbser.sys,10.0.19041.3636]
You are using driver version 10.0.19041.3636, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM14 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xC205CA39, 0x374C6488, 0x7C2098F6, 0x1C0CAFF2
Get Chip ID... [MT6771]
Get SOC ID... [76FA831F77C6CD45E985DF616796F4671FA300F95BBE46B2BDD242C6F7E1D776]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [9]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM8V8001JM-B813 (1000)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM8V8001JM-B813
UFS_FWVER : 1000
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000039000 (228.00Kb)
EXT_RAM : 0x0200000000 (8.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 10% - 20% device life time used
DeviceLifeTimeEstB: 10% - 20% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : alps
Product Manufacturer : alps
Product Model : oplus_mssi_64_cn
Product Name : sys_oplus_mssi_64_cn
Product Device : oplus_mssi_64_cn
Product Board : oppo6771
Board Platform : mt6771
Build ID : RP1A.200720.011
Build Date : Sat Dec 3 19:57:16 CST 2022
Display ID : RP1A.200720.011 release-keys
Security Patch : 2022-12-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 1670067820572
Userdata FS Type : EXT4
Read security partition from phone...
Decrypting security data... OK
Encrypt security data... OK
Read security partition from phone... OK
Write security partition to phone... error(1)


imei repair not work please check team