Help UFI ERROR Failed to initialize eMMC (return code: 17, CMD Error: Timeout) !!!

hafizbenito20 · Oct 25, 2020

Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8842-5181
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Failed to initialize eMMC (return code: 17, CMD Error: Timeout) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---

I TRIED MANY TIMES CPH1853 AND OTHER ALWAYS SHOW THIS ERROR
I AM USING V2 ADAPTER

KarimAfghan · May 19, 2021

Failed to initialize eMMC (return code: 17, CMD Error: Timeout) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---

Ples Help

Sweetsonu984 · May 19, 2021

due bad soldering at CMD, CLK, or DATA0 check agian your isp connection,
make sure isp connection jumper wire not long,.....USE Short isp jumper wire
isp only.... CMD CLK Data0 and GND and use USB for VCC and VCCQ

KarimAfghan · May 19, 2021

Connection status: XHCI:HUB3:[#0]:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8843-2970
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Failed to initialize eMMC (return code: 20, CMD Error: Invalid response) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---

It is still a problem

KarimAfghan · May 19, 2021

a217F model this is problum

habibrazmi · May 20, 2022

Please help. I have this problem. Is there a way to solve the problem? I test with Emate X the problem is solved, but I have this problem with the UFI socket 221-FBGA

aftab_ansari5287 · May 20, 2022

habibrazmi said:
View attachment 44285

Please help. I have this problem. Is there a way to solve the problem? I test with Emate X the problem is solved, but I have this problem with the UFI socket 221-FBGA

Maybe the EMMC is dead . that's why it's not booting.

habibrazmi · May 20, 2022

aftab_ansari5287 said:
Maybe the EMMC is dead . that's why it's not booting.

No, there is no problem with the EMMC . I tested it with up to 100 EMMC... This is the problem whit ufi box socket 221-FBGA

aftab_ansari5287 · May 21, 2022

Clean the point of the EMMC socket once . then check emmc.
it may also happen that your ufi socket is bad.

mushtech · Oct 1, 2022

Sweetsonu984 said:
due bad soldering at CMD, CLK, or DATA0 check agian your isp connection,
make sure isp connection jumper wire not long,.....USE Short isp jumper wire
isp only.... CMD CLK Data0 and GND and use USB for VCC and VCCQ

It happens even if am not connecting any phone, only connect isp adaptor

cellcarcol · Nov 30, 2022

KarimAfghan said:
a217F model this is problum

for this model you need to connect all the connections.

there are 7 in total

ifone · Dec 1, 2022

After this latest update now Im having issue siilar to others not detecting

tried snc files but seems error in sync

Synchronizing files...
updating file: app/qualcomm.Oppo.def (445.67 KiB)... CRC error
updating file: changes.txt (56.26 KiB)... CRC error
updating file: emmc/def/rpmb_keys.dat (612 bytes)... CRC error

Issue wont connect:

Boot version: 1.04, FW version: 1.14 (Aug 25 2021 04:56:05)
Insertion test... Done
Init bus...
VCC: 3.0 V, VCCQ: 1.8 V
Failed to initialize eMMC (return code: 1, CMD Error: Timeout) !!!
CMD3 error, cmd response: 0xFFFFFFFF, card state: 255 (Card is in unknown state)
SET_RELATIVE_ADDR command failed.

aftab_ansari5287 · Dec 1, 2022

ifone said:
After this latest update now Im having issue siilar to others not detecting

tried snc files but seems error in sync

Synchronizing files...
updating file: app/qualcomm.Oppo.def (445.67 KiB)... CRC error
updating file: changes.txt (56.26 KiB)... CRC error
updating file: emmc/def/rpmb_keys.dat (612 bytes)... CRC error

Issue wont connect:

Boot version: 1.04, FW version: 1.14 (Aug 25 2021 04:56:05)
Insertion test... Done
Init bus...
VCC: 3.0 V, VCCQ: 1.8 V
Failed to initialize eMMC (return code: 1, CMD Error: Timeout) !!!
CMD3 error, cmd response: 0xFFFFFFFF, card state: 255 (Card is in unknown state)
SET_RELATIVE_ADDR command failed.

Uninstall First then Delete Ufi Folder from C/drive.
Then install new setup & everything work now

ifone · Dec 7, 2022

aftab_ansari5287 said:
Uninstall First then Delete Ufi Folder from C/drive.
Then install new setup & everything work now

Thanks for the avised , its working now.

Boot version: 1.04, FW version: 1.14 (Aug 25 2021 04:56:05)
Insertion test... CLK not properly connected
Init bus...
VCC: 2.8 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: HAG4a2 (0x484147346132), rev: 0xA5, serial number: 0xC729C0FC
Manufacturing date: Aug 2018
CID: 90014A48 41473461 32A5C729 C0FC85EA
CSD: D0270132 8F5903FF FFFFFFE7 8A400016
Device version: 0x4105
Firmware version: 0xA5
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4 MiB
Boot2: 4 MiB
RPMB: 4 MiB
User area: 14.68 GiB(15,758,000,128 bytes)

Clear FRP Lock... Done

aftab_ansari5287 · Dec 7, 2022

ifone said:
Thanks for the avised , its working now.

Boot version: 1.04, FW version: 1.14 (Aug 25 2021 04:56:05)
Insertion test... CLK not properly connected
Init bus...
VCC: 2.8 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: HAG4a2 (0x484147346132), rev: 0xA5, serial number: 0xC729C0FC
Manufacturing date: Aug 2018
CID: 90014A48 41473461 32A5C729 C0FC85EA
CSD: D0270132 8F5903FF FFFFFFE7 8A400016
Device version: 0x4105
Firmware version: 0xA5
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4 MiB
Boot2: 4 MiB
RPMB: 4 MiB
User area: 14.68 GiB(15,758,000,128 bytes)

Clear FRP Lock... Done

Thanks for Report

cucipiring · Dec 8, 2022

habibrazmi said:
No, there is no problem with the EMMC . I tested it with up to 100 EMMC... This is the problem whit ufi box socket 221-FBGA

emmc socket max Bus speed 8bit
if lower you need new one or try to clean it.

Maani11 · Feb 19, 2023

Failed to initialize eMMC (return code: 17, CMD Error: Timeout) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---
--- Try to use 1 bit connection ---

Maani11 · Mar 1, 2023

aftab_ansari5287 said:
Clean the point of the EMMC socket once . then check emmc.
it may also happen that your ufi socket is bad.

Loading file: "\Xiaomi\Redmi%205A\ext_csd.bin", size: 512 bytes...
Writing extcsd, 512 bytes... Failed to switch[16][0,16,59] (return code: 1, CMD Error: Timeout) !!!
Failed to switch[17][0,17,1] (return code: 4, CMD Error: Invalid response) !!!
Failed to switch[31][0,31,1] (return code: 1, CMD Error: Timeout) !!!
Failed to switch[64][0,64,255] (return code: 4, CMD Error: Invalid response) !!!
Failed to switch[65][0,65,255] (return code: 1, CMD Error: Timeout) !!!
Failed to switch[66][0,66,55] (return code: 4, CMD Error: Invalid response) !!!
Failed to switch[110][0,110,0] (return code: 1, CMD Error: Timeout) !!!
Failed to switch[120][0,120,0] (return code: 4, CMD Error: Invalid response) !!!
Failed to switch[163][0,163,2] (return code: 1, CMD Error: Timeout) !!!
Failed to switch[183][0,183,2] (return code: 4, CMD Error: Invalid response) !!!
Done
Solution..........

aftab_ansari5287 · Mar 2, 2023

Maani11 said:
Loading file: "\Xiaomi\Redmi%205A\ext_csd.bin", size: 512 bytes...
Writing extcsd, 512 bytes... Failed to switch[16][0,16,59] (return code: 1, CMD Error: Timeout) !!!
Failed to switch[17][0,17,1] (return code: 4, CMD Error: Invalid response) !!!
Failed to switch[31][0,31,1] (return code: 1, CMD Error: Timeout) !!!
Failed to switch[64][0,64,255] (return code: 4, CMD Error: Invalid response) !!!
Failed to switch[65][0,65,255] (return code: 1, CMD Error: Timeout) !!!
Failed to switch[66][0,66,55] (return code: 4, CMD Error: Invalid response) !!!
Failed to switch[110][0,110,0] (return code: 1, CMD Error: Timeout) !!!
Failed to switch[120][0,120,0] (return code: 4, CMD Error: Invalid response) !!!
Failed to switch[163][0,163,2] (return code: 1, CMD Error: Timeout) !!!
Failed to switch[183][0,183,2] (return code: 4, CMD Error: Invalid response) !!!
Done
Solution..........

Use Old Version Ufi

IkaasRK · Mar 21, 2023

Please Help Me.. I Am Getting This Error

Search

Search

Help UFI ERROR Failed to initialize eMMC (return code: 17, CMD Error: Timeout) !!!

hafizbenito20

Junior Member

KarimAfghan

Member

Sweetsonu984

Friend's Martview

KarimAfghan

Member

KarimAfghan

Member

habibrazmi

Junior Member

aftab_ansari5287

habibrazmi

Junior Member

aftab_ansari5287

mushtech

Junior Member

cellcarcol

Active Member

ifone

Active Member

aftab_ansari5287

ifone

Active Member

aftab_ansari5287

cucipiring

Active Member

Maani11

Active Member

Maani11

Active Member

aftab_ansari5287

IkaasRK

Junior Member

Attachments