UMT Xiaomi Redmi Note 3 flash &frp done umt

[Yogesh B N]

Operation : Flash
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM6)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.7
Connecting to phone...OK
Waiting for response...Ignored
Init Handshake Sequence...OK
Hardware ID : E1009B00 [8976] 00000000
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8976_001]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8976, eMMC, 32 GB
LU Count : 1 [0x03A3E000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [sbl1.mbn] -> [sbl1] ...Done
Writing [sbl1.mbn] -> [sbl1bak] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [rpm.mbn] -> [rpmbak] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [tz.mbn] -> [tzbak] ...Done
Writing [hyp.mbn] -> [hyp] ...Done
Writing [hyp.mbn] -> [hypbak] ...Done
Writing [adspso.bin] -> [dsp] ...Done
Writing [sec.dat] -> [sec] ...Done
Writing [splash.img] -> [splash] ...Done
Writing [emmc_appsboot.mbn] -> [aboot] ...Done
Writing [emmc_appsboot.mbn] -> [abootbak] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [system.img ] -> [system]...Done
Writing [cache.img ] -> [cache]...Done
Writing [persist.img ] -> [persist]...Done
Writing [config.bin] -> [config] ...Done
Writing [mdtp.img] -> [mdtp] ...Done
Writing [cust.img ] -> [cust]...Done
Writing [cmnlib.mbn] -> [cmnlib] ...Done
Writing [keymaster.mbn] -> [keymaster] ...Done
Writing [cmnlib.mbn] -> [cmnlibbak] ...Done
Writing [keymaster.mbn] -> [keymasterbak] ...Done
Writing [userdata.img ] -> [userdata]...Done
Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done
Writing [gpt_backup0.bin] -> [BackupGPT] ...Done
Applying Patches................Done
Resetting device...Done
Operation Finished.
QcFire Ver. 6.3


Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM6)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.7
Connecting to phone...OK
Waiting for response...Ignored
Init Handshake Sequence...OK
Hardware ID : E1009B00 [8976] 00000000
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8976_001]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8976, eMMC, 32 GB
LU Count : 1 [0x03A3E000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi Redmi Note 3 [msm8952] [kenzo]
Brand : Xiaomi
Prod.Name : kenzo
Software : MMB29M, V10.2.1.0.MHOMIXM [Mon Jan 14 20:58:10 CST 2019]
Android Ver. : 6.0.1
Patch Level : 2018-07-01
Resetting FRP Lock......Done
Operation Finished.
QcFire Ver. 6.3