CM2 - SP3 Service Tool v2.30
probe UAC... Ok
Wait...
S/N: 00387228C4 v0163
initalize log engine... Ok
Build directories tree...
Backup files: C:\InfinityBox\CM2SP3\backup\
Backup files: 0 dirs: 0
Build device list... Ok 1648
Ready
Selected: Tecno B1G Boot [FF] FireFly nor
Boot [FF] FireFly protocol may be SLOW. For flash Read/Write use Boot [FDL] Factory
Selected: Tecno BG6h Boot [FF] FireFly mmc
Boot [FF] FireFly protocol may be SLOW. For flash Read/Write use Boot [FDL] Factory
Selected: Tecno BG6h Boot [FF] FireFly mmc
Boot [FF] FireFly protocol may be SLOW. For flash Read/Write use Boot [FDL] Factory
Selected: Tecno spark-Go-2024 Boot [FF] FireFly ufs
Boot [FF] FireFly protocol may be SLOW. For flash Read/Write use Boot [FDL] Factory
Operation: Connect Tecno spark-Go-2024 Boot [FF] FireFly [v2.30]
Wait...
Power device Off and connect cable now
Remember Volume Up/Down or Test-Point
Waiting for device...
Device found
PTFN: SPRD U2S Diag (COM13) vid 0x1782 pid 0x4D00
Handshake fail
Wrong connection mode?
Canceled
Finished 21 sec
Operation: Connect Tecno spark-Go-2024 Boot [FF] FireFly [v2.30]
Wait...
Power device Off and connect cable now
Remember Volume Up/Down or Test-Point
Waiting for device...
Device found
PTFN: SPRD U2S Diag (COM13) vid 0x1782 pid 0x4D00
boot: SPRD3
boot iLoader... Ok
start iLoader... Ok
Handshake... Ok
boot xLoader... Ok
start FireFly... Ok
Loader exec Ok
Dev UID: 608412f4d67fcc2c7313f9fc66bf9570593e605e0442c6860ef459f7628acc56
stored 6 hwid cache items
get storage info... MMC
EMMC CID: F40122415256313158134812AB791B45 crc Ok
Vendor: Biwin OEM: 290 ID: 415256313158 [ARV11X] PRV: 0x13
Serial: 1209183097 0x4812AB79
MM/YY: 1/2024
CSD: D02701320F5903FFFFFFFFEF8A404001
temp_write_protect: False
perm_write_protect: False
wp_group: 0x10 en 0x01
read extcsd... Ok
EXTCSD rev1.8 EMMC 5.1
ERASE_GROUP_DEF: 0x0400
BOOT_BUS_WIDTH: 0x00
PARTITION_CONFIG: 0x08
RST_N_FUNCTION: 0x01
PART_S_COMPLETED: False
BOOT size: 0x400000
RPMB size: 0x400000 4.00 Mb
WP_GRP_SIZE: 0x800000 8.00 Mb
Size: Market 64 Gb Actual 0xE90000000 58.25 Gb
EOL: Status: Normal: Less than 80% reserved blocks used
EOL_A: SLC status: 0% - 10% used
EOL_B: MLC status: 0% - 10% used
extcsd backup exist, skip: C:\InfinityBox\CM2SP3\backup\ext_csd\none_608412f4d67fcc2c_extcsd_00F4-Biwin_ARV11X_5.1_2024-11-05.bin
get partitions...
Load primary GPT...
Load secondary GPT...
Primary GPT state Ok
Secondary GPT state Ok
Partitions: 75
Connected
get sw info... 20 sec
Product Brand: TECNO
Product Device: TECNO-BG6
Product Model: TECNO BG6
Product Name: BG6
SW: TECNO/BG6-OP/TECNO-BG6:13/TP1A.220624.014/240822V2246:user/release-keys
Patch Level: TP1A.220624.014
Display ID: BG6-F069AfAgAhAiAjAkAlAmAnAsAtBsFaFbFcFdFeFfFgFhFiFjFkFlFuFv-TGo-OP-240822V2246
Product Name: BG6-OP
Ver. CodeName: REL
Ver. Release: 13
Sec. Patch: 2024-08-05
Build Time: 8/22/2024 2:33:08 PM
Product Info: BG6
SW: BG6-user 13 TP1A.220624.014 556 release-keys
SW Version: 240822V2246
Product Manfct: TECNO
Board Platform: ums9230
Product Board: TECNO-BG6
Android ver: 13
UserDataFS: 0x03 [f2fs] CacheFS: 0x03 [f2fs]
Device ID: bg6-tecno-bg6-bg6-op
Strategy: [tecno]
Firmware ID: UMS9230_TECNO_TECNO_BG6_OSv13_BG6-F069AfAgAhAiAjAkAlAmAnAsAtBsFaFbFcFdFeFfFgFhFiFjFkFlFuFv-TGo-OP-240822V2246_TP1A.220624.014_BG6
Backup exist: C:\InfinityBox\CM2SP3\backup\ums9230_608412f4d67fcc2c\
get slots... slot: b
[MemTool] load 75 items
Finished 36 sec
Operation: Reset | Format Tecno spark-Go-2024 Boot [FF] FireFly [v2.30]
WARNING: Reset may delete ALL USER DATA!
Continue? Yes
[+] Wipe
[-] Userdata
[+] FRP
[+] Smart
Reset Userdata is Off
If FRP still active after reset make Userdata On and repeat operation
Wait...
Partitions: 75
Backup exist: C:\InfinityBox\CM2SP3\backup\ums9230_608412f4d67fcc2c\
Process Wipe...
Reading... Ok
Writing... Ok
Process FRP...
Looking for items... 1 items found
[1] Writing... Ok
Process nvram...
[17] Format... Ok
[18] Format... Ok
Completed
Finished 16 sec
prodnv: sync before load;
miscdata: sync before load;
protect_data: sync before load;
uboot: sync before load;
trustos: sync before load;
Reboot... Disconnect cable if it freez
CMD 0x05 0x8E PHONE_WAIT_INPUT_TIMEOUT
Bye
