Selected model: Tecno KE6j (Tecno Spark 6 Air)
Operation: Erase FRP
Software version: 7.5
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to [BOX] in BROM mode
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM16 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x4D81A2EB, 0xBFBFB453, 0x08EDE7AA, 0x97E459B7
Get Chip ID... [MT6765]
Get SOC ID... [BDAE34556D592592195824C4B3062660E112F197B86B4EF7144D825411B8AC6B]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A68433861503E03002F376077C7
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: hC8aP>
EMMC_ID : 0x90014A68433861503E03002F376077C7
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x00C0000000 (3.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: info not available
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : TECNO
Product Manufacturer : TECNO MOBILE LIMITED
Product Model : TECNO KE6j
Product Name : KE6j-GL
Product Device : TECNO-KE6j
Product Board : TECNO-KE6j
Board Platform : mt6765
Build ID : QP1A.190711.020
Build Date : Tue Oct 12 14:44:55 CST 2021
Display ID : KE6j-H6215GH-Q-GL-211012V277
Security Patch : 2021-10-05
Version SDK : 29
Version Release : 10
Version Codename : REL
Firmware Version : GH-GL-211012V277
Userdata FS Type : F2FS
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Tecno_KE6j%20(Tecno%20Spark%206%20Air)/FRP_BACKUP_(2024-10-23_20-34-42)/
Format FRP... [P1] OK
Writting FRP data... OK
Fix TOOL DL Image error... OK
Erase FRP done!
Operation: Erase FRP
Software version: 7.5
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to [BOX] in BROM mode
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM16 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x4D81A2EB, 0xBFBFB453, 0x08EDE7AA, 0x97E459B7
Get Chip ID... [MT6765]
Get SOC ID... [BDAE34556D592592195824C4B3062660E112F197B86B4EF7144D825411B8AC6B]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A68433861503E03002F376077C7
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: hC8aP>
EMMC_ID : 0x90014A68433861503E03002F376077C7
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x00C0000000 (3.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: info not available
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : TECNO
Product Manufacturer : TECNO MOBILE LIMITED
Product Model : TECNO KE6j
Product Name : KE6j-GL
Product Device : TECNO-KE6j
Product Board : TECNO-KE6j
Board Platform : mt6765
Build ID : QP1A.190711.020
Build Date : Tue Oct 12 14:44:55 CST 2021
Display ID : KE6j-H6215GH-Q-GL-211012V277
Security Patch : 2021-10-05
Version SDK : 29
Version Release : 10
Version Codename : REL
Firmware Version : GH-GL-211012V277
Userdata FS Type : F2FS
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Tecno_KE6j%20(Tecno%20Spark%206%20Air)/FRP_BACKUP_(2024-10-23_20-34-42)/
Format FRP... [P1] OK
Writting FRP data... OK
Fix TOOL DL Image error... OK
Erase FRP done!