Legitunlocks.com
Wide Range LCD collection

Z3X Tecno BF7 (Tecno Spark Go 2023) dead , not conected in pandora 7.2

Z3X Team
N

nazirna

Active Member
Feb 8, 2019
18
2
Skype
[email protected]
whene press vol + and - mobile conect and show this error "
EMMC_ID: 0x65646F4D204D4F52A0000773120100D7
Load EMI from phone... Skip (read header error)
Load EMI config from database [DB VER: 222 DB DATE: 11-13-2023] error(3)
No compatible EMI found, select scatter for this model and try again
"i try to conect in preloader mode but nothing show in pandora box log.
Selected model: Tecno BF7 (Tecno Spark Go 2023)
Operation: Read Flash Info
Software version: 7.2

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM61 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0717
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0717
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM61 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0717
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xD4167660, 0xEDD0B96F, 0xE00BCB22, 0x370FB27F
Get Chip ID... [MT6761]
Get SOC ID... [99FDCFC5CC6AE7098D94565EA8A503916F75512EDE7E19D32A04760161944B10]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [5]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x65646F4D204D4F52A0000773120100D7
Load EMI from phone... Skip (read header error)
Load EMI config from database [DB VER: 222 DB DATE: 11-13-2023] error(3)
No compatible EMI found, select scatter for this model and try again
 
N

nazirna

Active Member
Feb 8, 2019
18
2
Skype
[email protected]
why team not responce on this post.same result in 7.2 and 7.3.not conecting in preloader mode.when try to firmware flashing .this error shown in log "
Read partitions info from phone... error(11)
Creating autoformat settings... OK
Format "EMMC_BOOT_1" partition( 0x00000000..0x001FFFFF )... error(STATUS_MMC_ERR)
"
Selected model: Tecno BF7 (Tecno Spark Go 2023)
Operation: Read PTT
Software version: 7.3

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM11 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0717
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0717
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM11 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0717
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xD4167660, 0xEDD0B96F, 0xE00BCB22, 0x370FB27F
Get Chip ID... [MT6761]
Get SOC ID... [99FDCFC5CC6AE7098D94565EA8A503916F75512EDE7E19D32A04760161944B10]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [5]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x65646F4D204D4F52A0000773120100D7
Load EMI from phone... Skip (read header error)
Load EMI config from database [DB VER: 222 DB DATE: 11-13-2023] error(3)
No compatible EMI found, select scatter for this model and try again



Selected model: Tecno BF7 (Tecno Spark Go 2023)
Operation: Flash (Format all + download)
Software version: 7.3

Parse scatter file... OK
Load Rom Images... OK
Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM11 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0717
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0717
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM11 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0717
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xD4167660, 0xEDD0B96F, 0xE00BCB22, 0x370FB27F
Get Chip ID... [MT6761]
Get SOC ID... [99FDCFC5CC6AE7098D94565EA8A503916F75512EDE7E19D32A04760161944B10]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [5]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x65646F4D204D4F52A0000773120100D7
Load EMI config from preloader... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: M MOR
EMMC_ID : 0x65646F4D204D4F52A0000773120100D7
EMMC_BOOT1: 0x0000200000 (2.00Mb)
EMMC_BOOT2: 0x0000200000 (2.00Mb)
EMMC_RPMB : 0x0000020000 (128.00Kb)
EMMC_USER : 0x0075700000 (1.83Gb)
RAM INFO:
INT_SRAM: 0x000003A500 (233.25Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: not defined
DeviceLifeTimeEstA: info not available
DeviceLifeTimeEstB: info not available
Get scatter info... OK
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... error(11)
Creating autoformat settings... OK
Format "EMMC_BOOT_1" partition( 0x00000000..0x001FFFFF )... error(STATUS_MMC_ERR)
 
You must log in or register to reply here.
Top