Z3X Samsung Galaxy A34 5G

Z3X Team

iph0ne7

Friend's Martview
Oct 26, 2019
113
33
Despite the success of the operation, the FRP was not removed.

Selected model: Samsung SM-A346B (Samsung Galaxy A34 5G)
Operation: Erase FRP
Software version: 7.9
Work ID: 52059900

Connect phone in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM39 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0959
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6877]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM39 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0959
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6877]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xE8B2BF30, 0x601ED3A3, 0x09B13534, 0x89E1B3B6
Get Chip ID... [MT6877]
Get SOC ID... [98FD844CC20068DB65881269B61ADC9221B375F1C53E9DD6128C986A9FF1D5D8]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [17]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): MT256GAXAU4U2281 (0003)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : MT256GAXAU4U2281
UFS_FWVER : 0003
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x3B96000000 (238.34Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0200000000 (8.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : samsung
Product Manufacturer : samsung
Product Model : SM-A346B
Product Name : a34xxx
Product Device : a34x
Product Board : a34x
Board Platform : mt6877
Build ID : SP1A.210812.016
Build Date : Fri Sep 27 20:57:32 KST 2024
Firmware Version : A346BXXS8CXI3
Userdata FS Type : F2FS
Read partition "frp"... OK
Read partition "persistent"... OK
Format FRP... [P1] [P2] OK
Writting FRP data... OK
Erase FRP done!
 

Mttmoussa

Friend's Martview
Aug 25, 2019
121
26
Despite the success of the operation, the FRP was not removed.

Selected model: Samsung SM-A346B (Samsung Galaxy A34 5G)
Operation: Erase FRP
Software version: 7.9
Work ID: 52059900

Connect phone in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM39 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0959
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6877]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM39 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0959
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6877]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xE8B2BF30, 0x601ED3A3, 0x09B13534, 0x89E1B3B6
Get Chip ID... [MT6877]
Get SOC ID... [98FD844CC20068DB65881269B61ADC9221B375F1C53E9DD6128C986A9FF1D5D8]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [17]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): MT256GAXAU4U2281 (0003)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : MT256GAXAU4U2281
UFS_FWVER : 0003
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x3B96000000 (238.34Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0200000000 (8.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : samsung
Product Manufacturer : samsung
Product Model : SM-A346B
Product Name : a34xxx
Product Device : a34x
Product Board : a34x
Board Platform : mt6877
Build ID : SP1A.210812.016
Build Date : Fri Sep 27 20:57:32 KST 2024
Firmware Version : A346BXXS8CXI3
Userdata FS Type : F2FS
Read partition "frp"... OK
Read partition "persistent"... OK
Format FRP... [P1] [P2] OK
Writting FRP data... OK
Erase FRP done!
wipe and frp 100%
 
Top