Legitunlocks.com
Microscope Full Range

Z3X Redmi Note 11T 5g Security Repair Issue Repair Done But Patch cert Say Unkown Xiaomi Model

Z3X Team
Selected model: Xiaomi Redmi Note 11 5G (China) (Evergo)
Operation: Repair
Software version: 5.1

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to [BOX] in BROM mode
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM28 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xD9321CCE, 0x87C33FF7, 0x98341341, 0xA1346C8A
Get Chip ID... [MT6833]
Get SOC ID... [27D8E0EBA13FCC36521BE0C566C6148971DD20268207A152B99BAD95AE9653F8]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): MT128GAXAU2U227X (0102)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : MT128GAXAU2U227X
UFS_FWVER : 0102
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EXT4] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : evergo
Product Name : evergo_in
Product Device : evergo
Product Board : evergo
Board Platform : MT6833
Build ID : RP1A.200720.011
Build Date : Tue Dec 7 10:28:08 CST 2021
Display ID : CUST_evergo
Security Patch : 2021-12-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : V12.5.2.0.RGBINXM
Userdata FS Type : F2FS
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI 1: 1111111111111111
IMEI 2: 11111111111111111
Repairing IMEI...
IMEI 1: 866600000000000
IMEI 2: 8660000000000000
Write IMEI [NVDATA]... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!
If your phone after repair keeps rebooting - use wipe data option.
Now use "Patch Cert" option to complete repair.
 
Click to expand...
TorCaesar

TorCaesar

Friend's Martview
Mar 11, 2021
211
55
Pakistan
TorCaesar said:
Selected model: Xiaomi Redmi Note 11 5G (China) (Evergo)
Operation: Repair
Software version: 5.1

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to [BOX] in BROM mode
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM28 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xD9321CCE, 0x87C33FF7, 0x98341341, 0xA1346C8A
Get Chip ID... [MT6833]
Get SOC ID... [27D8E0EBA13FCC36521BE0C566C6148971DD20268207A152B99BAD95AE9653F8]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): MT128GAXAU2U227X (0102)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : MT128GAXAU2U227X
UFS_FWVER : 0102
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EXT4] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : evergo
Product Name : evergo_in
Product Device : evergo
Product Board : evergo
Board Platform : MT6833
Build ID : RP1A.200720.011
Build Date : Tue Dec 7 10:28:08 CST 2021
Display ID : CUST_evergo
Security Patch : 2021-12-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : V12.5.2.0.RGBINXM
Userdata FS Type : F2FS
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI 1: 1111111111111111
IMEI 2: 11111111111111111
Repairing IMEI...
IMEI 1: 866600000000000
IMEI 2: 8660000000000000
Write IMEI [NVDATA]... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!
If your phone after repair keeps rebooting - use wipe data option.
Now use "Patch Cert" option to complete repair.
Click to expand...
Finally DoneWithout Hardware Modification Dual Great Team Work Great Task Thanks


Selected model: Xiaomi Redmi Note 11S 5G (Opal)
Operation: Repair
Software version: 5.1

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to [BOX] in BROM mode
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM28 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xD9321CCE, 0x87C33FF7, 0x98341341, 0xA1346C8A
Get Chip ID... [MT6833]
Get SOC ID... [27D8E0EBA13FCC36521BE0C566C6148971DD20268207A152B99BAD95AE9653F8]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): MT128GAXAU2U227X (0102)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : MT128GAXAU2U227X
UFS_FWVER : 0102
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EXT4] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : evergo
Product Name : evergo_in
Product Device : evergo
Product Board : evergo
Board Platform : MT6833
Build ID : RP1A.200720.011
Build Date : Tue Dec 7 10:28:08 CST 2021
Display ID : CUST_evergo
Security Patch : 2021-12-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : V12.5.2.0.RGBINXM
Userdata FS Type : F2FS
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI 1: 000000000000000
IMEI 2: 000000000000000
Repairing IMEI...
IMEI 1: 866111111111111
IMEI 2: 866611111111111
Write IMEI and patch CERT [NVDATA]... OK
Load partiton for patching... OK
Patching...
Selected "Auto unlock bootloader"
Read security partition from phone... OK
Decrypting security data... OK
Encrypt security data... OK
Write security partition to phone... OK
Unlock bootloader done!
Selected "Disable VBMETA verification"
Read security partition from phone... OK
Write security partition to phone... OK
Write IMEI and patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security and Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.
 
  • Like
Reactions: Ahmed_Dooha
You must log in or register to reply here.
Top