Steps:-
1. Connect phone into EDL Mode using TP Point.
2. Run UMT QcFire Tool and goto the tab Read & Tools.
3. Then choose Format FS from drop down
4. It will ask for Reset FRP too then click yes.
Operation : Format FS
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM69)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Connecting to phone...OK
Waiting for response...Ignored
Init Handshake Sequence...OK
Hardware ID : E1F00B00 [8937] 00007200
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8937_035]...Done
Executing Loader...OK
Auth Enabled Device! You need Mi Auth Account to service!
Skipping Auth...OK
Detecting Chip Type...OK
Hardware : 8937, eMMC, 32 GB
LU Count : 1 [0x03A3E000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi Redmi 8A [olivelite]
Brand : Xiaomi
Prod.Name : olivelite
Software : ZQL2116-olivelite-build-20200530052012, V11.0.9.0.PCPINXM [Sat May 30 05:21:32 CST 2020]
Android Ver. : 9
Patch Level : 2020-05-01
Formatting userdata [SafeMode]...Done
Resetting FRP Lock......Done
Operation Finished.
QcFire Ver. 6.3
1. Connect phone into EDL Mode using TP Point.
2. Run UMT QcFire Tool and goto the tab Read & Tools.
3. Then choose Format FS from drop down
4. It will ask for Reset FRP too then click yes.
Operation : Format FS
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM69)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Connecting to phone...OK
Waiting for response...Ignored
Init Handshake Sequence...OK
Hardware ID : E1F00B00 [8937] 00007200
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8937_035]...Done
Executing Loader...OK
Auth Enabled Device! You need Mi Auth Account to service!
Skipping Auth...OK
Detecting Chip Type...OK
Hardware : 8937, eMMC, 32 GB
LU Count : 1 [0x03A3E000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi Redmi 8A [olivelite]
Brand : Xiaomi
Prod.Name : olivelite
Software : ZQL2116-olivelite-build-20200530052012, V11.0.9.0.PCPINXM [Sat May 30 05:21:32 CST 2020]
Android Ver. : 9
Patch Level : 2020-05-01
Formatting userdata [SafeMode]...Done
Resetting FRP Lock......Done
Operation Finished.
QcFire Ver. 6.3
