Post here successfully Unlocked / Repaired / Flashed operations via NCK BOX

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview

Micromax Q385 SC7731G
Flash And Imei Repair Done




EXE: NckBox Spreadtrum Module 0.4
ACTION: Flash Firmware.
SCENARIO: SC7715
Selected firmware: zsw1511_mmx.pac
Start Detect phone.
Phone must be off with battery inside.
Long press "VOL -" key while inserting usb cable.
For some phones need to
Long press "VOL -"+ "VOL +" key while inserting usb cable.
Keep key untill boot complete.
Detected: SPRD U2S Diag (COM4)
BOOT: SPRD3
Sending loader, keep boot key untill loader start.
Reconnecting phone...
Detected: SPRD U2S Diag (COM4)
Loader OK: Spreadtrum Boot Block version 1.1
Changing bautrate OK.
First boot done.
Send Second Loader.
Repartition OK.
IMEI 1 to write: 911495350866489
IMEI 2 to write: 911495350957387
Start write: wfixnv1
IMEI 1 to write: 911495350866489
IMEI 2 to write: 911495350957387
Start write: wcnfixnv1
Start write: prodnv
[uboot]Format OK.
Start write: splloader
Start write: wmodem
Start write: wdsp
Start write: wcnmodem
Start write: boot
Start write: recovery
Start write: system
Drop comunication, waiting for data
Drop comunication, waiting for data
Drop comunication, waiting for data
Drop comunication, waiting for data
Drop comunication, waiting for data
Drop comunication, waiting for data
Drop comunication, waiting for data
Drop comunication, waiting for data
Start write: persist
Start write: userdata
Start write: logo
[wruntimenv1]Format OK.
[wcnruntimenv1]Format OK.
Start write: cache
[misc]Format OK.
Start write: uboot
Flashing done.
 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview

VODAFONE V785 MT6572
NETWORK UNLOCK DONE


Code:
Selected connection metod: FLASH Mode
Exe version: NCKBox AndroidMTK 1.8.7.7
Selected model: Vodafone 785
Action: Unlock
Reinsert phone battery. 
Battery must be charged.
Phone must be off with battery inside. 
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM12)
Boot mode: Preloader
Phone detected...Please wait
Sending DA agent, please wait...
BaseBand CPU :MT6572_S00
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 512 MB DRAM
----------------------------------------------------
EMMC: (29Gb+4096Mb) TOSIBA 0x303034473930 
EMMC FW VERSION: 10:00:00:00:00:00:00:00
EMMC CID: 11010030303447 : 000000000000000000
EMMC UA SIZE: 0xec000000 
BOOT STYLE: EMMC BOOT
FULL LENGTH: 0xec480000 [3.692 GB]
Preloader SEC version: 2
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detecting high speed port, wait......
Detected : MediaTek DA USB VCOM (Android) (COM15)
OTP IMEI: 355250065057589
MODEL FROM PROINFO: V785-2BVDGB1
SECRO FROM PROINFO: X2A0HE00AN00
Reading security, wait...
SIM[1]: 
Block1(N): Locked (remain:2) Code : 19774426 
Block2(NS): Unlocked
Block3(SP): Unlocked
Block4(C): Unlocked
Unlocking target...please wait.
Unlock finished.
Wait untill phone will start charging.
All done.


 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview
Intex Aqua T5 MT6571
Stuck On Logo Done


Code:
Flash files count is :9
Action : Firmware update.
Selected Model: 0-By CPU: MT6571_NAND
Exe version: NCKBox AndroidMTK 1.8.7.7
Scenario: [1]Full Flash
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM5)
Boot mode: Preloader
Phone detected...Please wait
Sending DA agent, please wait...
BaseBand CPU :MT6571_S00
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 256 MB DRAM
----------------------------------------------------
NAND: (4Gb+2048Mb) [KINGSTON] KTN0403CS_TCR1
BOOT STYLE : NAND BOOT
Size: 0x20000000 [0.500 GB]
BlockSize: 4096 SpareSize: 208 BMT Blocks 80
Preloader SEC version: 2
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detecting high speed port, wait......
Detected : MediaTek DA USB VCOM (Android) (COM8)
Flash NAND Algo Start.
FORMAT NAND FLASH : BEGIN: 0x185c0000 - LEN: 0x300000
FORMAT NAND FLASH : BEGIN: 0x188c0000 - LEN: 0x68c0000
Send preloader...
Send preloader...
Download firmware to flash now...
Wait untill phone will start charging.
 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview
Intex Aqua Power HD MT6592
Stuck On Logo Solve
Code:
Flash files count is :13
Action : Firmware update.
Selected Model: 0-By CPU: MT6592
Exe version: NCKBox AndroidMTK 1.8.7.7
Scenario: [1]Full Flash
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM5)
Boot mode: Preloader
Phone detected...Please wait
Sending DA agent, please wait...
BaseBand CPU :MT6592_S00
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 2 GB DRAM
----------------------------------------------------
EMMC: (116Gb+16384Mb) SAMSUNG 0x523832314d42
EMMC FW VERSION: 00:00:00:00:00:00:00:00
EMMC CID: 15010052383231 : 000000000000000000
EMMC UA SIZE: 0x3a3e00000
BOOT STYLE: EMMC BOOT
FULL LENGTH: 0x3a4a00000 [14.572 GB]
Preloader SEC version: 2
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detecting high speed port, wait......
Detected : MediaTek DA USB VCOM (Android) (COM8)
Flash EMMC Algo Start.
Preloader saved in firmware directory.
Starting flash.
FORMAT EMMC FLASH : BEGIN: 0x6b800000 - LEN: 0x1a800000
FORMAT EMMC FLASH : BEGIN: 0x86000000 - LEN: 0x31c900000
Send preloader...
Download firmware to flash now...
Wait untill phone will start charging.​



 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview
Micromax E313 MT6592
Stuck On Logo Solve
Code:
Flash files count is :13
Action : Firmware update.
Selected Model: 0-By CPU: MT6592
Exe version: NCKBox AndroidMTK 1.8.7.7
Scenario: [1]Full Flash
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek USB Port (COM9)
Boot mode: Brom
Phone detected...Please wait
Sending DA agent, please wait...
BaseBand CPU :MT6592_S00
BaseBand CPU Secure Version : 05
BaseBand CPU Bootloader Version : 00
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 1 GB DRAM
----------------------------------------------------
EMMC: (56Gb+8192Mb) KSI 0x563130303038
EMMC FW VERSION: 50:00:00:00:00:00:00:00
EMMC CID: 70010056313030 : 000000000000000000
EMMC UA SIZE: 0x1c3000000
BOOT STYLE: EMMC BOOT
FULL LENGTH: 0x1c3c00000 [7.059 GB]
Preloader SEC version: 2
Status: USB_FULL_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detecting high speed port, wait......
Detected : MediaTek DA USB VCOM (Android) (COM8)
Flash EMMC Algo Start.
Preloader saved in firmware directory.
Starting flash.
FORMAT EMMC FLASH : BEGIN: 0x85000000 - LEN: 0x8000000
FORMAT EMMC FLASH : BEGIN: 0x8d000000 - LEN: 0x134b00000
Send preloader...
Download firmware to flash now...
Wait untill phone will start charging.​



 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview
Karbonn A1+ Champ 3G MT6572
Password Unlock Done

TRIED MANUELY BUT NOT SOLVE
THEN I FLASH 100% SOLVE
Code:
Flash files count is :9
Action : Firmware update.
Selected Model: 0-By CPU: MT6572_NAND
Exe version: NCKBox AndroidMTK 1.8.7.7
Scenario: [1]Full Flash
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : PreLoader USB VCOM Port (COM8)
Boot mode: Preloader
Phone detected...Please wait
Sending DA agent, please wait...
BaseBand CPU :MT6572_S00
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 256 MB DRAM
----------------------------------------------------
NAND: (4Gb+2048Mb) [KINGSTON] KTN0403CS_TCR1
BOOT STYLE : NAND BOOT
Size: 0x20000000 [0.500 GB]
BlockSize: 4096 SpareSize: 224 BMT Blocks 80
Preloader SEC version: 2
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detecting high speed port, wait......
Detected : DA USB VCOM Port (COM7)
Flash NAND Algo Start.
FORMAT NAND FLASH : BEGIN: 0x142c0000 - LEN: 0x700000
FORMAT NAND FLASH : BEGIN: 0x149c0000 - LEN: 0xa1c0000
Send preloader...
Download firmware to flash now...
Wait untill phone will start charging.​



 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview
Micromax A46 MT6572
Stuck On Logo Solve
Code:
Flash files count is :9
Action : Firmware update.
Selected Model: 0-By CPU: MT6572_NAND
Exe version: NCKBox AndroidMTK 1.8.7.7
Scenario: [1]Full Flash
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM5)
Boot mode: Preloader
Phone detected...Please wait
Sending DA agent, please wait...
BaseBand CPU :MT6572_S00
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 256 MB DRAM
----------------------------------------------------
NAND: (4Gb+2048Mb) [Hynix] H9TA4GH2GDMCPR
BOOT STYLE : NAND BOOT
Size: 0x20000000 [0.500 GB]
BlockSize: 2048 SpareSize: 64 BMT Blocks 80
Preloader SEC version: 2
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detecting high speed port, wait......
Detected : MediaTek DA USB VCOM (Android) (COM8)
Flash NAND Algo Start.
FORMAT NAND FLASH : BEGIN: 0x15b40000 - LEN: 0x700000
FORMAT NAND FLASH : BEGIN: 0x16240000 - LEN: 0x9380000
Send preloader...
Download firmware to flash now...
Wait untill phone will start charging.
 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview
Micromax A106 MT6582
Stuck On Logo Solved


Flashing





Code:
Flash files count is :12
Action : Firmware update.
Selected Model: 0-By CPU: MT6582
Exe version: NCKBox AndroidMTK 1.8.7.7
Scenario: [1]Full Flash
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM5)
Boot mode: Preloader
Phone detected...Please wait
Sending DA agent, please wait...
BaseBand CPU :MT6582_S01
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 1 GB DRAM
----------------------------------------------------
EMMC: (58Gb+8192Mb) HYNIX 0x483847326404
EMMC FW VERSION: 05:00:00:00:00:00:00:00
EMMC CID: 90014A48384732 : 000000000000000000
EMMC UA SIZE: 0x1d2000000
BOOT STYLE: EMMC BOOT
FULL LENGTH: 0x1d2c00000 [7.293 GB]
Preloader SEC version: 2
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detecting high speed port, wait......
Detected : MediaTek DA USB VCOM (Android) (COM8)
Flash EMMC Algo Start.
Preloader saved in firmware directory.
Starting flash.
FORMAT EMMC FLASH : BEGIN: 0x3e180000 - LEN: 0x7e00000
FORMAT EMMC FLASH : BEGIN: 0x45f80000 - LEN: 0x39c00000
Send preloader...
Download firmware to flash now...
Wait untill phone will start charging.



Repair Imei
Code:
Selected connection metod: Meta Connection
Exe version: NCKBox AndroidMTK 1.8.7.7
Selected phone: MT6582
Action : IMEI REPAIR.
IMEI[1] for write : 911430704228144
IMEI[2] for write : 911430706928147
Scanning for presents meta ports...
Meta ports not detected, starting brom stage.
Phone must be off with battery inside.
Please insert USB cable now...
In some phones need to keep VOL- button untill inserting USB cable.
[5]Detected: MediaTek PreLoader USB VCOM (Android) (COM5)
\\?\usb#vid_0e8d&pid_2000#6&944c330&0&2#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
Starting META mode, wait...
Restarting to meta,wait....
If drivers missing, please install CDC drivers.
This can take up to 5 min on slow phones.
If take too long, check device manager for drivers.
[18]META Port Detected: MediaTek USB VCOM (Android) (COM18)
USB\VID_0E8D&PID_2007\6&944C330&0&2
Start sync target, waiting responce.....
[AP]BaseBand CPU : MT6582,S01
[META]BaseBand CPU : MT6582, E01
[META]SW_VER : MOLY.WR8.W1315.MD.WG.MP.V34
[META]HW_VER : TINNO82_WET_KK_HSPA_HW
Meta mode conected ok, start reading phone....
IMEI to repair: [1] 911430704228144
Phone imei[1] : 911430704228144
IMEI to repair: [2] 911430706928147
Phone imei[2] : 911430706928147
Clean Boot flag ok.​


 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview
Micromax Q355 MT6582
Stuck On Logo Solved Just Flashed By NCK






Code:
Flash files count is :12
Action : Firmware update.
Selected Model: 0-By CPU: MT6582
Exe version: NCKBox AndroidMTK 1.8.7.7
Scenario: [1]Full Flash
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : PreLoader USB VCOM Port (COM8)
Boot mode: Preloader
Phone detected...Please wait
Sending DA agent, please wait...
BaseBand CPU :MT6582_S01
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 1 GB DRAM
----------------------------------------------------
EMMC: (58Gb+8192Mb) HYNIX 0x483847326404
EMMC FW VERSION: 05:00:00:00:00:00:00:00
EMMC CID: 90014A48384732 : 000000000000000000
EMMC UA SIZE: 0x1d2000000
BOOT STYLE: EMMC BOOT
FULL LENGTH: 0x1d2c00000 [7.293 GB]
Preloader SEC version: 2
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview

Gionee P2 MT6572 Auto Wifi On Solved



Code:
 Flash files count is :15
 Action : Firmware update.
 Selected Model: 0-By CPU: MT6572_EMMC
 Exe version: NCKBox AndroidMTK 1.8.7.7
 Scenario: [1]Full Flash
 Reinsert phone battery. 
 Battery must be charged.
 Phone must be off with battery inside. 
 Please insert USB cable now...
 Detected : MediaTek PreLoader USB VCOM (Android) (COM5)
 Boot mode: Preloader
 Phone detected...Please wait
 Sending DA agent, please wait...
 BaseBand CPU :MT6572_S00
 BaseBand CPU Secure Version : FF
 BaseBand CPU Bootloader Version : 01
----------------------------------------------------
 INT RAM: 128 KB SDRAM
 EXT RAM: 512 MB  DRAM
----------------------------------------------------
 EMMC: (29Gb+4096Mb) SAMSUNG 0x4e35575a4d42 
 EMMC FW VERSION: 01:00:00:00:00:00:00:00
 EMMC CID: 1501004E35575A : 000000000000000000
 EMMC UA SIZE: 0xe9000000      
 BOOT STYLE: EMMC BOOT
 FULL LENGTH: 0xe9480000       [3.645 GB]
 Preloader SEC version: 2
 Status: USB_HIGH_SPEED
 Detecting high speed port, wait......
 If driver not installed, install high speed port driver.
 If not need high speed port, disable it.
 After repeat opperation.
 Detecting high speed port, wait......
 Detected : MediaTek DA USB VCOM (Android) (COM8)
 Flash EMMC Algo Start.
 Preloader saved in firmware directory.
 Starting flash.
 FORMAT EMMC FLASH :  BEGIN: 0x3c9c0000       - LEN: 0x17800000      
 FORMAT EMMC FLASH :  BEGIN: 0x541c0000       - LEN: 0x74000000      
 Send preloader...
 Download firmware to flash now...
 Wait untill phone will start charging.


 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview

Karbonn A6 Turbo MT6571 Stuck On Logo Solved



Code:
 Flash files count is :11
 Action : Firmware update.
 Selected Model: 0-By CPU: MT6571_EMMC
 Exe version: NCKBox AndroidMTK 1.8.7.7
 Scenario: [1]Full Flash
 Reinsert phone battery. 
 Battery must be charged.
 Phone must be off with battery inside. 
 Please insert USB cable now...
 Detected : MediaTek PreLoader USB VCOM (Android) (COM5)
 Boot mode: Preloader
 Phone detected...Please wait
 Sending DA agent, please wait...
 BaseBand CPU :MT6571_S00
 BaseBand CPU Secure Version : FF
 BaseBand CPU Bootloader Version : 01
----------------------------------------------------
 INT RAM: 128 KB SDRAM
 EXT RAM: 512 MB  DRAM
----------------------------------------------------
 EMMC: (29Gb+4096Mb) HYNIX 0x483447326111 
 EMMC FW VERSION: 01:00:00:00:00:00:00:00
 EMMC CID: 90014A48344732 : 000000000000000000
 EMMC UA SIZE: 0xe9000000      
 BOOT STYLE: EMMC BOOT
 FULL LENGTH: 0xe9c00000       [3.652 GB]
 Preloader SEC version: 2
 Status: USB_HIGH_SPEED
 Detecting high speed port, wait......
 If driver not installed, install high speed port driver.
 If not need high speed port, disable it.
 After repeat opperation.
 Detecting high speed port, wait......
 Detected : MediaTek DA USB VCOM (Android) (COM8)
 Flash EMMC Algo Start.
 Preloader saved in firmware directory.
 Starting flash.
 FORMAT EMMC FLASH :  BEGIN: 0x35b60000       - LEN: 0x8000000      
 FORMAT EMMC FLASH :  BEGIN: 0x3db60000       - LEN: 0x49600000      
 Send preloader...
 Download firmware to flash now...
 Wait untill phone will start charging


 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview

Micromax Q355 MT6582
android.system has stopped Solved




Code:
 Flash files count is :12
 Action : Firmware update.
 Selected Model: 0-By CPU: MT6582
 Exe version: NCKBox AndroidMTK 1.8.7.7
 Scenario: [1]Full Flash
 Reinsert phone battery. 
 Battery must be charged.
 Phone must be off with battery inside. 
 Please insert USB cable now...
 Detected : MediaTek PreLoader USB VCOM (Android) (COM5)
 Boot mode: Preloader
 Phone detected...Please wait
 Sending DA agent, please wait...
 BaseBand CPU :MT6582_S01
 BaseBand CPU Secure Version : FF
 BaseBand CPU Bootloader Version : 01
----------------------------------------------------
 INT RAM: 128 KB SDRAM
 EXT RAM: 1 GB  DRAM
----------------------------------------------------
 EMMC: (58Gb+8192Mb) HYNIX 0x483847326404 
 EMMC FW VERSION: 05:00:00:00:00:00:00:00
 EMMC CID: 90014A48384732 : 000000000000000000
 EMMC UA SIZE: 0x1d2000000    
 BOOT STYLE: EMMC BOOT
 FULL LENGTH: 0x1d2c00000      [7.293 GB]
 Preloader SEC version: 2
 Status: USB_HIGH_SPEED
 Detecting high speed port, wait......
 If driver not installed, install high speed port driver.
 If not need high speed port, disable it.
 After repeat opperation.
 Detecting high speed port, wait......
 Detected : MediaTek DA USB VCOM (Android) (COM8)
 Flash EMMC Algo Start.
 Preloader saved in firmware directory.
 Starting flash.
 FORMAT EMMC FLASH :  BEGIN: 0xa2100000       - LEN: 0x10000000      
 FORMAT EMMC FLASH :  BEGIN: 0xb2100000       - LEN: 0x11f600000    
 Send preloader...
 Download firmware to flash now...
 Wait untill phone will start charging.


 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview

Spice Xlife 425 3G MT6572 Stuck On Logo Solved



Code:
 Flash files count is :12
 Action : Firmware update.
 Selected Model: 0-By CPU: MT6572_EMMC
 Exe version: NCKBox AndroidMTK 1.8.7.7
 Scenario: [1]Full Flash
 Reinsert phone battery. 
 Battery must be charged.
 Phone must be off with battery inside. 
 Please insert USB cable now...
 Detected : MediaTek PreLoader USB VCOM (Android) (COM5)
 Boot mode: Preloader
 Phone detected...Please wait
 Sending DA agent, please wait...
 BaseBand CPU :MT6572_S00
 BaseBand CPU Secure Version : FF
 BaseBand CPU Bootloader Version : 01
----------------------------------------------------
 INT RAM: 128 KB SDRAM
 EXT RAM: 512 MB  DRAM
----------------------------------------------------
 EMMC: (29Gb+4096Mb) HYNIX 0x483447326111 
 EMMC FW VERSION: 01:00:00:00:00:00:00:00
 EMMC CID: 90014A48344732 : 000000000000000000
 EMMC UA SIZE: 0xe9000000      
 BOOT STYLE: EMMC BOOT
 FULL LENGTH: 0xe9c00000       [3.652 GB]
 Preloader SEC version: 2
 Status: USB_HIGH_SPEED
 Detecting high speed port, wait......
 If driver not installed, install high speed port driver.
 If not need high speed port, disable it.
 After repeat opperation.
 Detecting high speed port, wait......
 Detected : MediaTek DA USB VCOM (Android) (COM8)
 Flash EMMC Algo Start.
 Preloader saved in firmware directory.
 Starting flash.
 FORMAT EMMC FLASH :  BEGIN: 0x58a40000       - LEN: 0xf000000      
 FORMAT EMMC FLASH :  BEGIN: 0x67a40000       - LEN: 0x80cc0000      
 Send preloader...
 Download firmware to flash now...
 Wait untill phone will start charging.


 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview

Videocon A16 MT6572 Blinking Problem Solved



Code:
Flash files count is :9
 Action : Firmware update.
 Selected Model: 0-By CPU: MT6572_NAND
 Exe version: NCKBox AndroidMTK 1.8.7.7
 Scenario: [1]Full Flash
 Reinsert phone battery. 
 Battery must be charged.
 Phone must be off with battery inside. 
 Please insert USB cable now...
 Detected : MediaTek PreLoader USB VCOM (Android) (COM5)
 Boot mode: Preloader
 Phone detected...Please wait
 Sending DA agent, please wait...
 BaseBand CPU :MT6572_S00
 BaseBand CPU Secure Version : FF
 BaseBand CPU Bootloader Version : 01
----------------------------------------------------
 INT RAM: 128 KB SDRAM
 EXT RAM: 256 MB  DRAM
----------------------------------------------------
 NAND: (4Gb+2048Mb) [Micron] NAND_MT29C4G48MAAHBAAKS_5WT 
 BOOT STYLE : NAND BOOT
 Size: 0x20000000       [0.500 GB]
 BlockSize: 4096 SpareSize: 224  BMT Blocks 80
 Preloader SEC version: 2
 Status: USB_HIGH_SPEED
 Detecting high speed port, wait......
 If driver not installed, install high speed port driver.
 If not need high speed port, disable it.
 After repeat opperation.
 Detecting high speed port, wait......
 Detected : MediaTek DA USB VCOM (Android) (COM8)
 Flash NAND Algo Start.
 FORMAT NAND FLASH :  BEGIN: 0x115c0000       - LEN: 0x700000        
 FORMAT NAND FLASH :  BEGIN: 0x11cc0000       - LEN: 0xd8c0000      
 Send preloader...
 Download firmware to flash now...
 Wait untill phone will start charging.


 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview

Lenevo A269i MT6572 Stuck On Logo Done



Code:
 Flash files count is :9
 Action : Firmware update.
 Selected Model: 0-By CPU: MT6572_NAND
 Exe version: NCKBox AndroidMTK 1.8.7.7
 Scenario: [1]Full Flash
 Reinsert phone battery. 
 Battery must be charged.
 Phone must be off with battery inside. 
 Please insert USB cable now...
 Detected : MediaTek PreLoader USB VCOM Port (COM7)
 Boot mode: Preloader
 Phone detected...Please wait
 Sending DA agent, please wait...
 BaseBand CPU :MT6572_S00
 BaseBand CPU Secure Version : FF
 BaseBand CPU Bootloader Version : 01
----------------------------------------------------
 INT RAM: 128 KB SDRAM
 EXT RAM: 256 MB  DRAM
----------------------------------------------------
 NAND: (4Gb+2048Mb) [SAMSUNG] K9K8G16U0K 
 BOOT STYLE : NAND BOOT
 Size: 0x20000000       [0.500 GB]
 BlockSize: 4096 SpareSize: 128  BMT Blocks 80
 Preloader SEC version: 2
 Status: USB_HIGH_SPEED
 Detecting high speed port, wait......
 If driver not installed, install high speed port driver.
 If not need high speed port, disable it.
 After repeat opperation.
 Detecting high speed port, wait......
 Detected : MediaTek DA USB VCOM Port (COM8)
 Flash NAND Algo Start.
 FORMAT NAND FLASH :  BEGIN: 0xf880000        - LEN: 0x4600000      
 FORMAT NAND FLASH :  BEGIN: 0x13e80000       - LEN: 0xad00000      
 Send preloader...
 Download firmware to flash now...
 Wait untill phone will start charging.


 

Forum Supporter

Friend's Martview
Jan 31, 2017
3,189
6,449
Martview

Micromax Q340 MT6582 Privacy Protection Reset Done



Code:
 Exe version: NCKBox AndroidMTK 1.8.7.8
 Selected model: MT6582
 Action: Reset Privacy
 Reinsert phone battery. 
 Battery must be charged.
 Phone must be off with battery inside. 
 Please insert USB cable now...
 Detected : MediaTek PreLoader USB VCOM Port (COM7)
 Boot mode: Preloader
 Phone detected...Please wait
 Sending DA agent, please wait...
 BaseBand CPU :MT6582_S01
 BaseBand CPU Secure Version : FF
 BaseBand CPU Bootloader Version : 01
----------------------------------------------------
 EMMC: (58Gb+8192Mb) HYNIX 0x483847316505 
 EMMC FW VERSION: 07:00:00:00:00:00:00:00
 EMMC CID: 90014A48384731 : 000000000000000000
 EMMC UA SIZE: 0x1d2000000    
 BOOT STYLE: EMMC BOOT
 FULL LENGTH: 0x1d2c00000      [7.293 GB]
 Preloader SEC version: 2
 Dumping data, wait.
 Value found, procesing[010c][002c0000]
 Resetting phone.
 FORMAT EMMC FLASH :  BEGIN: 0x8ab00000       - LEN: 0x39c00000      
 Phone can start slow at first power on
 If phone stuck on logo, perform wipe from recovery.
 First start can take up to 5 min on some phones


 
Top