Z3X Pandora PRO 7.14 Released. Lot of New devices and new loaders added

[GsmToto]

Selected model: Spreadtrum Spreadtrum
Operation: Read Partitions
Software version: 7.12



Product Brand : benco
Product Manufacturer : INONE
Product Model : AEOP519
Product Name : AEOP519
Product Device : AEOP519
Product Board : op503_ums9230_1h10
Board Platform : ums9230
Build ID : TP1A.220624.014
Build Date : Fri Jul 5 20:41:57 CST 2024
Display ID : benco_AEOP519_S152_24G05
Security Patch : 2024-06-05
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : 50
Userdata FS Type : F2FS

 

[GsmToto]

Selected model: Xiaomi Poco C31 (Angelicain)
Operation: Repair
Software version: 7.12

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM3 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM3 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x042C3A1D, 0x08A77314, 0x183A7D06, 0x4B7BB917
Get Chip ID... [MT6765]
Get SOC ID... [7AE5D692FE452B853C63FD216310645BB490FE5DF5253DB47609185719B3950D]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x9B01006029749C759325030363400F1D
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: Y2P064
EMMC_ID : 0x9B010056029749C79325030363400F1D
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : POCO
Product Manufacturer : Xiaomi
Product Model : 211033MI
Product Name : angelicain_in
Product Device : angelicain
Product Board : angelicain
Board Platform : mt6765
Build ID : QP1A.190711.020
Build Date : Sun Sep 12 11:13:43 CST 2021
Display ID : QP1A.190711.020
Security Patch : 2021-09-01
Version SDK : 29
Version Release : 10
Version Codename : REL
Firmware Version : V12.0.1.0.QCRINRF
Userdata FS Type : F2FS
Read security partition from phone...
Decrypting security data... OK
Encrypt security data... OK
Load partiton for patching... OK
Checking boot patch possiblity... POSSIBLE WITH BOOT UNLOCK
Patching CERT... OK
Save patched partiton... OK
Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.

 

[aliipi]

Selected model: Infinix X6526 (Infinix Smart 8 Plus)
Operation: Erase FRP
Software version: 7.12
Work ID: 58422210

Connect phone in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM (Android),usb2ser.sys,3.0.1511.0]
You are using driver version 3.0.1511.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM26 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0xDCA79FF5, 0x73151C50, 0x7455C2F5, 0x1ACD4BBC
Load DownloadAgent... OK
Search DA... OK [1]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... error(STATUS_SEC_INVALID_DA_VER)

 

[GsmToto]

Selected model: Xiaomi Redmi A1+ (Ice)
Operation: Erase FRP
Software version: 7.12


Connect phone in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1511.0]
You are using driver version 3.0.1511.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM7 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1511.0]
You are using driver version 3.0.1511.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM7 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x58DE85F8, 0xCE904A0B, 0xFAEC1071, 0xD81308B4
Get Chip ID... [MT6765]
Get SOC ID... [496E486C5FCE17BH565D1827CCA07C8D14D0CA98D43HBDB56 867B42F055103W]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0xD62D0T4D4D433634W7510C1464F3B99W
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: MMC64G
EMMC_ID : 0xD62D004D4D433VR447510C1D64F3B99W
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x00C0000000 (3.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EROFS] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : water
Product Name : water_global
Product Device : water
Product Board : water
Board Platform : mt6765
Build ID : SP1A.210812.016
Build Date : Mon Aug 14 22:05:34 CST 2023
Display ID : 13 V14.0.15.0.TGOMIXB
Security Patch : 2023-08-01
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : V14.0.15.0.TGOMIXM
Userdata FS Type : F2FS
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Xiaomi_Redmi%20A1%2B%20(Ice)/FRP_BACKUP_(2025-1-22_20-17-57)/
Format FRP... [P1] OK
Writting FRP data... OK
Erase FRP done!

 

[GsmToto]

Selected model: Mediatek Mediatek
Operation: Wipe Data
Software version: 7.12


Connect phone in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM5 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM5 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x420C483B, 0x03AC0807, 0x0814898B, 0xBC4365FA
Get Chip ID... [MT6833]
Get SOC ID... [7022FCEA02F8AK5AFDD812732FFF96B62S23AEC1F8716DB648 D78BA275E6C0F5]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0xD6010S41334135363R126FA3E62D59EM
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: A3A561
EMMC_ID : 0xD6010341K34135363D126FA3E62D59EM
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E67800000 (57.62Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 10% - 20% device life time used
DeviceLifeTimeEstB: info not available
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EXT4] ... OK
Product Brand : ZTE
Product Manufacturer : ZTE
Product Model : ZTE 7540N
Product Name : P633F08_2
Product Device : P633F08
Product Board : Crabapple
Board Platform : mt6833
Build ID : RP1A.200720.011
Build Date : Wed Jun 19 16:56:04 CST 2024
Display ID : MyOS11.1.3_7540N_PJ_VDC_ZA
Security Patch : 2024-06-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 20240619.162606
Userdata FS Type : F2FS
Formatting "userdata" partition... OK
Formatting "metadata" partition... OK
Wipe data done!

 

[aliipi]

Selected model: Realme RMX3890 (Realme C67 4G)
Operation: Factory Reset
Software version: 7.13
Work ID: 58702811

Waiting for device... OK
Device found at COM52
Port: Qualcomm HS-USB QDLoader 9008
Open port... OK
Reading device info... OK
Serial Number: 698691351
Sahara ver: 2
OEM PK HASH: D53F19D28ED8CA4A5D9C5BD7DDB365DBC9268CBDE3DFC8A151E70C8B0A0DFFC210BBF251AE8BDED0F5714DE3FC1D0AA5
CPU: SM6225 (Snapdragon 680 4G)
Vendor: Oppo/Oneplus
MSM HW ID: 001B80E100510000
SBL SW Ver: 00000000
Prepare loader file... error
Necessary loader not found(2)

 

[sweetboy]

Selected model: Qualcomm Qualcomm
Operation: Erase FRP
Software version: 7.13
Work ID: 58722020

Waiting for device... OK
Device found at COM30
Port: Qualcomm HS-USB QDLoader 9008
Open port... OK
Reading device info... OK
Serial Number: 4064031359
Sahara ver: 2
OEM PK HASH: 74D7B554B446ABAB2F9FDCD473E9874E29DDC353C04BE65D82FE00230BA819D088FE2609400DB5DFE345B3BEB8C18A9F
CPU: SM6225 (Snapdragon 680 4G)
Vendor: Samsung
MSM HW ID: 001B80E100200000
SBL SW Ver: 00000000
Prepare loader file... error
Necessary loader not found(2)

need loader for frp please

 

[GsmToto]

Selected model: Infinix Mediatek
Operation: Erase FRP
Software version: 7.13


Connect phone in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1511.0]
You are using driver version 3.0.1511.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM3 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1511.0]
You are using driver version 3.0.1511.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM3 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xA0E3453C, 0x8C3A3037, 0x2C1DFAD2, 0x72BB52CE
Get Chip ID... [MT6768]
Get SOC ID... [988DF8F59A49BE84B1896B4BCB2E7F8AB83C8457F09C81A8ED E22DCEE4286778]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [8]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A6843396150560101300060491S
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: hC9aP3
EMMC_ID : 0x90014A6847396150330101300060474S
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: info not available
DeviceLifeTimeEstB: 10% - 20% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : Infinix
Product Manufacturer : INFINIX MOBILITY LIMITED
Product Model : Infinix X690
Product Name : X690-GL
Product Device : Infinix-X690
Product Board : Infinix-X690
Board Platform : mt6768
Build ID : QP1A.190711.020
Build Date : Tue Feb 15 16:02:46 CST 2022
Display ID : X690-H691BCFG-Q-GL-220215V382
Security Patch : 2022-02-05
Version SDK : 29
Version Release : 10
Version Codename : REL
Firmware Version : BCFG-GL-220215V382
Userdata FS Type : F2FS
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Infinix_MT6768/FRP_BACKUP_(2025-1-23_17-45-32)/
Format FRP... [P1] OK
Writting FRP data... OK
Fix TOOL DL Image error... OK
Erase FRP done!

 

[GsmToto]

Selected model: Samsung SM-M022G (Samsung Galaxy M02)
Operation: Remove KG
Software version: 7.13


Connect phone in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1633,usb2ser.sys,3.0.1504.0]
Device found at COM3[BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0699
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CB00, SW VER: 0002, HW SUB CODE: 8A00
Detect chip [MT6739]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1633,usb2ser.sys,3.0.1504.0]
Device found at COM3 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0699
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CB00, SW VER: 0002, HW SUB CODE: 8A00
Detect chip [MT6739]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xF00A10C2, 0x89B5526B, 0xE5D6DE8B, 0xCB70D51C
Get Chip ID... [MT6739]
Get SOC ID... [1F567A8D3C7C2075B856029899467264FA0562DBB611582292 5D6E98560D986C]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [1]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x15010047586642414200489CF2723896
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: GX6BAB
EMMC_ID : 0x15010047583642464200489CF2723896
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0747C00000 (29.12Gb)
RAM INFO:
INT_SRAM: 0x0000020000 (128.00Kb)
EXT_RAM : 0x00C0000000 (3.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : samsung
Product Manufacturer : samsung
Product Model : SM-M022G
Product Name : a02ins
Product Device : a02
Product Board : k39tv1_bsp_titan_hamster
Board Platform : mt6739
Build ID : QP1A.190711.020
Build Date : Mon Aug 16 18:54:52 KST 2021
Display ID : QP1A.190711.020.M022GXXU2AUH6
Security Patch : 2021-07-01
Version SDK : 29
Version Release : 10
Version Codename : REL
Firmware Version : M022GXXU2AUH1
Userdata FS Type : F2FS
Read Write Counter[WC][MAX=0xFFFFFFFF]... 132634 OK
Read RPMB... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Samsung_SM-M022G%20(Samsung%20Galaxy%20M06)/
Searching RPMB key... found! [3]
Write RPMB... OK
Read Write Counter[WC][MAX=0xFFFFFFFF]... 132636 OK
Reset (Samsung KG) RPMB done!

 

[Xsa-Scorpion]

Plz focus about this update
Realme latest sec network regional lock
Note 50
Note 60
C61
C63
….and
Anti crack for infinix tecno
Some latest model oppo mode prealoder not work
And i hope to support
SM-A155F -SM-A156E-SM-A245F
And finaly about vivo latest sec if you can supported with credit valable
Thanks team z3x

 

[GsmToto]

Selected model: Samsung SM-M022G (Samsung Galaxy M02)
Operation: Remove KG
Software version: 7.13


Connect phone in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1633,usb2ser.sys,3.0.1504.0]
Device found at COM3[BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0699
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CB00, SW VER: 0002, HW SUB CODE: 8A00
Detect chip [MT6739]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1633,usb2ser.sys,3.0.1504.0]
Device found at COM3 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0699
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CB00, SW VER: 0002, HW SUB CODE: 8A00
Detect chip [MT6739]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xF00A10C2, 0x89B5526B, 0xE5D6DE8B, 0xCB70D51C
Get Chip ID... [MT6739]
Get SOC ID... [1F567A8D3C7C2075B856029899467224FA0562DBB611582292 5D6E98520D986C]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [1]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x15010047583642414200489CF2723893
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: GX6BAB
EMMC_ID : 0x15010047583642414200489CF2723893
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0747C00000 (29.12Gb)
RAM INFO:
INT_SRAM: 0x0000020000 (128.00Kb)
EXT_RAM : 0x00C0000000 (3.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : samsung
Product Manufacturer : samsung
Product Model : SM-M022G
Product Name : a02ins
Product Device : a02
Product Board : k39tv1_bsp_titan_hamster
Board Platform : mt6739
Build ID : QP1A.190711.020
Build Date : Mon Aug 16 18:54:52 KST 2021
Display ID : QP1A.190711.020.M022GXXU2AUH1
Security Patch : 2021-07-01
Version SDK : 29
Version Release : 10
Version Codename : REL
Firmware Version : M022GXXU2AUH1
Userdata FS Type : F2FS
Read Write Counter[WC][MAX=0xFFFFFFFF]... 132634 OK
Read RPMB... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Samsung_SM-M022G%20(Samsung%20Galaxy%20M02)/
Searching RPMB key... found! [3]
Write RPMB... OK
Read Write Counter[WC][MAX=0xFFFFFFFF]... 132636 OK
Reset (Samsung KG) RPMB done!

 

[GsmToto]

Selected model: Xiaomi Redmi A2+ (Water)
Operation: Repair
Software version: 7.12


Connect phone in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1633,usb2ser.sys,3.0.1504.0]
Device found at COM3 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1633,usb2ser.sys,3.0.1504.0]
Device found at COM3 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xF918DC2F, 0x8C1B8F88, 0x4C4593D0, 0x8F9C117E
Get Chip ID... [MT6765]
Get SOC ID... [7CB5560147AB16E4224621C64128C6650E8ED0EE89AC74171E A594EF16292E89]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0xD62D004D4D433634475103E62D6C3A2B
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: MMC64G
EMMC_ID : 0xD62D004D4D433634475103E62D6C3A2B
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x00C0000000 (3.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EROFS] ... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : water
Product Name : water_global
Product Device : water
Product Board : water
Board Platform : mt6765
Build ID : SP1A.210812.016
Build Date : Wed Oct 9 11:31:53 CST 2024
Display ID : 13 V14.0.35.0.TGOMIXM
Security Patch : 2024-09-01
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : V14.0.35.0.TGOMIXM
Userdata FS Type : F2FS
Read partition "nvdata"... OK
Read partition "protect1"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read security files... OK
Calculating... OK
Read IMEI... OK
IMEI 1: 86145
IMEI 2: 86145
Repairing IMEI...
IMEI 1: 8645
IMEI 2: 8645
Write IMEI and patch CERT [NVDATA]... OK
Load partiton for patching... [Nov 2024] ... OK
Write IMEI and patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security and Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.

 

[aliipi]

Selected model: Tecno KL5 (Tecno Spark 30C)
Operation: Erase FRP And Wipe
Software version: 7.13
Erasing of partitions can damage your device.
Make sure that you have a backup created. Continue? YES
Work ID: 59356336

Connect phone in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM (Android),usb2ser.sys,3.0.1511.0]
You are using driver version 3.0.1511.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM34 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0xAA69E9B3, 0x00C68631, 0x3247649A, 0xF59206D5
Load DownloadAgent... OK
Search DA... OK [4]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... error(STATUS_SEC_INVALID_DA_VER)

 

[GsmToto]

Selected model: Tecno KI5K (Tecno Spark 10C)
Operation: Erase FRP And Wipe
Software version: 7.13


Connect phone in BROM mode. Use volume key buttons or testpoint.
Waiting for device... OK
Device found at COM5
Port: USB\VID_1782&PID_4D00\6&298C69D9&0&3
Driver: [UNISOC Communications Inc.,sprdvcom,SPRD U2S Diag,sprdvcom.sys,4.19.38.134]
Port type: BROM
Connecting to device... OK
Selected processor: Tiger_T612_64
Load files... (universal) OK
Connect preloader 1... OK
Connect preloader 2... OK
Connect loader 1... OK
Connect loader 2... OK
Serial Number: 0987604N15197373
Flash Type: UFS
Read partitions info... OK
Checking A/B state... OK [A]
Read product info... [EROFS] ... OK
Product Brand : TECNO
Product Manufacturer : TECNO
Product Model : TECNO KI5k
Product Name : KI5k-GL
Product Device : TECNO-KI5k
Product Board : TECNO-KI5k
Board Platform : ums9230
Build ID : SP1A.210812.016
Build Date : Mon Aug 14 17:34:43 CST 2023
Display ID : KI5k-F065-S-GL-V501-20230814
Security Patch : 2023-08-05
Version SDK : 31
Version Release : 12
Version Codename : REL
Firmware Version : GL-20230814V501
Userdata FS Type : F2FS
Backup partitions... OK
Formatting "persist" partition... OK
Formatting "userdata" partition... OK
Formatting "cache" partition... OK
Formatting "metadata" partition... OK
Creating default filesystems... [CACHE: EXT4] ... [USERDATA: F2FS] ... OK
Done!

 

[shakir77]

Pandora PRO 7.14 Released. Lot of New devices and new loaders added


Added support Samsung Galaxy S25 series:

- SM-S9310 (BIT 1)
- SM-S931B (BIT 1)
- SM-S931N (BIT 1)
- SM-S931U (BIT 1)
- SM-S9360 (BIT 1)
- SM-S936B (BIT 1)
- SM-S936N (BIT 1)
- SM-S936U (BIT 1)
- SM-S9380 (BIT 1)
- SM-S938B (BIT 1)
- SM-S938N (BIT 1)
- SM-S938U (BIT 1)


Added new loader for Samsung:

- SM-A015U1 (BIT 7)
- SM-A426N (BIT 7)
- SM-A5260 (BIT B)
- SM-A528N (BIT 6)
- SM-A736B (BIT A)
- SM-A908B (BIT 9)
- SM-F916B (BIT 7)
- SM-G781N (BIT A)
- SM-G986N (BIT A)
- SM-G990B2 (BIT A)
- SM-G991U (BIT E)
- SM-G998U (BIT E)
- SM-M426B (BIT 9)
- SM-T297 (BIT 6)
- SM-T733 (BIT 8)


Added support for Unisoc based phones:

- Realme C61 RMX3930/RMX3933, Realme C63 RMX3939
- ZTE Blade A53 Plus P963F62, ZTE Blade A53 P963F62-B
- ZTE Blade A53 Pro P963F63, ZTE Blade V2022 8031



Added:

- Xiaomi MiAcc info reading

Added:
- new loaders for QCOM phones (EDL mode)


Fixed:
- QCOM Get PkHash exception
- QCOM EMMC sparse flashing BUG
- QCOM patch flashing BUG
- QCOM Xiaomi auth



DO NOT POST ANY LOGS OF JOB HERE in this thread, if you have any error - open own thread and supporters will answer there!!!

List of resellers with stock: HERE

vivo old model flashing not support HA Ha Ha pd1930cf pd1930f vivo y11 .. old model till not suport what is the reason ... ?

 

[Asad_1112]

Pandora PRO 7.14 Released. Lot of New devices and new loaders added


Added support Samsung Galaxy S25 series:

- SM-S9310 (BIT 1)
- SM-S931B (BIT 1)
- SM-S931N (BIT 1)
- SM-S931U (BIT 1)
- SM-S9360 (BIT 1)
- SM-S936B (BIT 1)
- SM-S936N (BIT 1)
- SM-S936U (BIT 1)
- SM-S9380 (BIT 1)
- SM-S938B (BIT 1)
- SM-S938N (BIT 1)
- SM-S938U (BIT 1)


Added new loader for Samsung:

- SM-A015U1 (BIT 7)
- SM-A426N (BIT 7)
- SM-A5260 (BIT B)
- SM-A528N (BIT 6)
- SM-A736B (BIT A)
- SM-A908B (BIT 9)
- SM-F916B (BIT 7)
- SM-G781N (BIT A)
- SM-G986N (BIT A)
- SM-G990B2 (BIT A)
- SM-G991U (BIT E)
- SM-G998U (BIT E)
- SM-M426B (BIT 9)
- SM-T297 (BIT 6)
- SM-T733 (BIT 8)


Added support for Unisoc based phones:

- Realme C61 RMX3930/RMX3933, Realme C63 RMX3939
- ZTE Blade A53 Plus P963F62, ZTE Blade A53 P963F62-B
- ZTE Blade A53 Pro P963F63, ZTE Blade V2022 8031



Added:

- Xiaomi MiAcc info reading

Added:
- new loaders for QCOM phones (EDL mode)


Fixed:
- QCOM Get PkHash exception
- QCOM EMMC sparse flashing BUG
- QCOM patch flashing BUG
- QCOM Xiaomi auth



DO NOT POST ANY LOGS OF JOB HERE in this thread, if you have any error - open own thread and supporters will answer there!!!

List of resellers with stock: HERE

Realme C63 Repair After Mobile Restart Please Fix Update Pandora Z3x Team Please And Please Vivo Update Preloader Pandora Team Please

 

[tefisoagsm]

how to fix please?







Selected model: OPPO CPH2371 (Oppo Reno7 5G)
Operation: Repair
Software version: 7.14
Work ID: 59517566

Connect phone in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM_V1632 (Android),usb2ser.sys,3.0.1504.0]
Device found at COM26 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0959
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6877]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0x7ABBF536, 0x1421EA7A, 0x61D666DD, 0xC39388B5
Load DownloadAgent... OK
Search DA... OK [0]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [PRELOADER]
Preloader alive. Skip initializing external RAM
Send preloader... OK
Load DownloadAgent... OK
Search DA... OK [17]
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM8F9001JM-B813
UFS_FWVER : 0700
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x3B96000000 (238.34Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0200000000 (8.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
[EFUSE INFO]: BROM not disabled
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : OPPO
Product Manufacturer : OPPO
Product Model : CPH2371
Product Name : CPH2371EEA
Product Device : OPD4A1L1
Product Board : k6877v1_64_k419
Board Platform : mt6877
Build ID : TP1A.220905.001
Build Date : Fri Apr 21 19:08:44 CST 2023
Display ID : CPH2371_13.1.0.500(EX01)
Security Patch : 2023-04-05
Version Release : 13
Firmware Version : R.fe60b9_2
Userdata FS Type : F2FS
Read security partition from phone...
Decrypting security data... OK
Encrypt security data... OK
Read partition "nvdata"... OK
Read partition "protect1"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read security files... OK
Calculating... OK
Repairing IMEI...
IMEI 1: 111111111111119
IMEI 2: 222222222222228
Write IMEI and patch CERT [NVDATA]... OK
Checking patch type... patch impossible

 

[irfan111]

plz add vivo new securty (2024)

 

[tefisoagsm]

Checking patch type... patch impossible

 

[usman5752]

Selected model: OPPO CPH2579 (Oppo A38)
Operation: Read IMEI Info
Software version: 7.14
Work ID: 59577140

Connect phone in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM_V2023 (Android),usb2ser_mtk.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM17 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0x068A4E69, 0x9B78F842, 0x392C9EAA, 0xA813CD95
Load DownloadAgent... OK
Search DA... OK [1]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... error(STATUS_SEC_INVALID_DA_VER)