Selected model: OPPO CPH2119 (OPPO F17 Pro)
Operation: Repair
Software version: 7.4
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM7 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0725
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6779]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM7 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0725
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6779]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xBF223EA9, 0xFDCCC321, 0xE563A4FC, 0x756591D6
Get Chip ID... [MT6779]
Get SOC ID... [00340F3E539EED7AB9ED600F9B5CB78F01CBD5EE8C6469FA717FD5848637C8C4]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [10]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM8V7001JM-B810 (1200)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM8V7001JM-B810
UFS_FWVER : 1200
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000080000 (512.00Kb)
EXT_RAM : 0x0200000000 (8.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 20% - 30% device life time used
DeviceLifeTimeEstB: 20% - 30% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : OPPO
Product Manufacturer : OPPO
Product Model : CPH2119
Product Name : CPH2119
Product Device : OP4C51L1
Product Board : k79v1_64
Board Platform : mt6779
Build ID : SP1A.210812.016
Build Date : Fri Jun 28 17:29:30 CST 2024
Display ID : CPH2119_11_F.52
Security Patch : 2024-07-05
Version Release : 12
Firmware Version : Q.18c4a0a_ee53
Userdata FS Type : EXT4
Read security partition from phone...
Decrypting security data... OK
Encrypt security data... OK
Read partition "nvdata"... OK
Read partition "protect1"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read security files... OK
Calculating... OK
Repairing IMEI...
IMEI 1: XXXXXXXXXXXXX
IMEI 2: XXXXXXXXXXXXX
Write IMEI and patch CERT [NVDATA]... OK
Checking patch type... [2]
Patching CERT... OK
Save patched partiton... OK
Updating NVRAM... OK
Read security partition from phone... OK
Write security partition to phone... OK
Checking additional lock... [ENABLED]
Disable additional lock... OK
Unlock bootloader done!
Selected "Disable VBMETA verification"
Read security partition from phone... OK
Write security partition to phone... OK
Write IMEI and patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security and Patch cert done!
Operation: Repair
Software version: 7.4
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM7 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0725
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6779]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM7 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0725
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6779]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xBF223EA9, 0xFDCCC321, 0xE563A4FC, 0x756591D6
Get Chip ID... [MT6779]
Get SOC ID... [00340F3E539EED7AB9ED600F9B5CB78F01CBD5EE8C6469FA717FD5848637C8C4]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [10]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM8V7001JM-B810 (1200)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM8V7001JM-B810
UFS_FWVER : 1200
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000080000 (512.00Kb)
EXT_RAM : 0x0200000000 (8.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 20% - 30% device life time used
DeviceLifeTimeEstB: 20% - 30% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : OPPO
Product Manufacturer : OPPO
Product Model : CPH2119
Product Name : CPH2119
Product Device : OP4C51L1
Product Board : k79v1_64
Board Platform : mt6779
Build ID : SP1A.210812.016
Build Date : Fri Jun 28 17:29:30 CST 2024
Display ID : CPH2119_11_F.52
Security Patch : 2024-07-05
Version Release : 12
Firmware Version : Q.18c4a0a_ee53
Userdata FS Type : EXT4
Read security partition from phone...
Decrypting security data... OK
Encrypt security data... OK
Read partition "nvdata"... OK
Read partition "protect1"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read security files... OK
Calculating... OK
Repairing IMEI...
IMEI 1: XXXXXXXXXXXXX
IMEI 2: XXXXXXXXXXXXX
Write IMEI and patch CERT [NVDATA]... OK
Checking patch type... [2]
Patching CERT... OK
Save patched partiton... OK
Updating NVRAM... OK
Read security partition from phone... OK
Write security partition to phone... OK
Checking additional lock... [ENABLED]
Disable additional lock... OK
Unlock bootloader done!
Selected "Disable VBMETA verification"
Read security partition from phone... OK
Write security partition to phone... OK
Write IMEI and patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security and Patch cert done!