Oppo F11 Pro Only Connect Handset IS Dead

[GsmRock]

Oppo F11 Pro After connect Ufi Box Only Click Identify eMMC THen SHow this Error

Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-0526
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: hC8aP (0x68433861503e), rev: 0x03, serial number: 0xCB553087
Manufacturing date: Nov 2018
CID: 90014A68 43386150 3E03CB55 3087B598
CSD: D0270032 8F5903FF FFFFFFEF 8E400042
Failed to read EXT_CSD !!!

REconnect some time but handset cannot connect

THen Remove ISP Pinout HandSet Is dead

I Try to Service Center But Service centre firmware Cannot flash show only mtk Port

I need CLK & CMD Any Registrance

My Handset At time Dead PLZ Help Seniors

PLz Help Need Solution

 

[aftab_ansari5287]

Oppo F11 Pro After connect Ufi Box Only Click Identify eMMC THen SHow this Error

Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-0526
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: hC8aP (0x68433861503e), rev: 0x03, serial number: 0xCB553087
Manufacturing date: Nov 2018
CID: 90014A68 43386150 3E03CB55 3087B598
CSD: D0270032 8F5903FF FFFFFFEF 8E400042
Failed to read EXT_CSD !!!

REconnect some time but handset cannot connect

THen Remove ISP Pinout HandSet Is dead

I Try to Service Center But Service centre firmware Cannot flash show only mtk Port

I need CLK & CMD Any Registrance

My Handset At time Dead PLZ Help Seniors

PLz Help Need Solution

CHECK ISP PINOUT
IF NOT WORK
JUST CONTACT ME WHATSAPP 9792648446

 

[msibashankar]

Oppo F11 Pro After connect Ufi Box Only Click Identify eMMC THen SHow this Error

Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-0526
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: hC8aP (0x68433861503e), rev: 0x03, serial number: 0xCB553087
Manufacturing date: Nov 2018
CID: 90014A68 43386150 3E03CB55 3087B598
CSD: D0270032 8F5903FF FFFFFFEF 8E400042
Failed to read EXT_CSD !!!

REconnect some time but handset cannot connect

THen Remove ISP Pinout HandSet Is dead

I Try to Service Center But Service centre firmware Cannot flash show only mtk Port

I need CLK & CMD Any Registrance

My Handset At time Dead PLZ Help Seniors

PLz Help Need Solution

DATA JUMPAR REMOVE RESOLDERING THEN TRY AND FLASH ONLY EXT CSD FILE

 

[GsmRock]

DATA JUMPAR REMOVE RESOLDERING THEN TRY AND FLASH ONLY EXT CSD FILE

I Try some methods resoled isp points then Clean re check test REcoonect connection but only show this error

plz help

 

[reliableshop]

Data 0 not connected but all connection is ok any solution.

 

[Repair Hub]

Oppo F11, Oppo F11 Pro MTK Port Only Dead After ISP Jumpers


----------