Selected model: OPPO CPH2239 (OPPO A54)
Operation: Repair
Software version: 6.5
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM4 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Install LibUSB... OK
Waiting for device... OK
Open port... OK
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM4 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x8A4B2753, 0x7B5E1625, 0x226069DF, 0xBD26B411
Get Chip ID... [MT6765]
Get SOC ID... [D5FF22111B6077A8FE7497E4C2189941398F542F6A67BFF59F1DD349B615868A]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x13014E53304A394B3910279D910158CB
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: S0J9K9
EMMC_ID : 0x13014E53304A394B3910279D910158CB
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x1D1F000000 (116.48Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : OPPO
Product Manufacturer : alps
Product Model : CPH2239
Product Name : vnd_oppo6765
Product Device : oppo6765
Product Board : oppo6765
Board Platform : mt6765
Build ID : RP1A.200720.011
Build Date : Tue Feb 8 15:34:11 CST 2022
Display ID : CPH2239_11_C.01
Security Patch : 2022-02-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 1644304518397
Read security partition from phone...
Decrypting security data... OK
Encrypt security data... OK
Read partition "nvdata"... OK
Read partition "protect1"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read security files... OK
Calculating... OK
Repairing IMEI...
IMEI 1: 000000000000000
IMEI 2: 000000000000000
Write IMEI and patch CERT [NVDATA]... OK
Checking patch type... error(2.ERR_SF_4)
Operation: Repair
Software version: 6.5
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM4 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Install LibUSB... OK
Waiting for device... OK
Open port... OK
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM4 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x8A4B2753, 0x7B5E1625, 0x226069DF, 0xBD26B411
Get Chip ID... [MT6765]
Get SOC ID... [D5FF22111B6077A8FE7497E4C2189941398F542F6A67BFF59F1DD349B615868A]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x13014E53304A394B3910279D910158CB
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: S0J9K9
EMMC_ID : 0x13014E53304A394B3910279D910158CB
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x1D1F000000 (116.48Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EROFS] ... OK
Product Brand : OPPO
Product Manufacturer : alps
Product Model : CPH2239
Product Name : vnd_oppo6765
Product Device : oppo6765
Product Board : oppo6765
Board Platform : mt6765
Build ID : RP1A.200720.011
Build Date : Tue Feb 8 15:34:11 CST 2022
Display ID : CPH2239_11_C.01
Security Patch : 2022-02-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 1644304518397
Read security partition from phone...
Decrypting security data... OK
Encrypt security data... OK
Read partition "nvdata"... OK
Read partition "protect1"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read security files... OK
Calculating... OK
Repairing IMEI...
IMEI 1: 000000000000000
IMEI 2: 000000000000000
Write IMEI and patch CERT [NVDATA]... OK
Checking patch type... error(2.ERR_SF_4)