when i got the device camera problem. after that i flash with umt device automatically goes to the Qualcomm 9008 qdloader port.
after flash the umt .Here is the log.
Device : Nokia TA-1011
Operation : Read Information
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM11)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1009600 [8909] 00000000
OPK_DATA : A57FDEEB0D02233786D8DDCA8A9889D62F92D43EE56EAC9966 024663C39A5B06
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8909_051]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8909, eMMC, 8 GB
LU Count : 1 [0x00E90000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : FIH FIH-E1M-FIH [msm8909] [E1M]
Software : 00WW_1_15P, 00WW_1_15P [Thu Oct 11 20:11:59 CST 2018]
Android Ver. : 8.1.0
Patch Level : 2018-10-01
USERDATA : Normal
You can use RESET LOCKS to remove Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 4.5
now i flash with Nokia__Dynamo_00WW__E1M__600WW Using Infinity best Nk2 device again won't turn on. please help me.
now device not connect in edl 9008 qdloader port. device connect in Diagnostic port 900E
How to recover Qualcomm qdloader 9008 port Again
Please Help me. it ll be humble Thanks.
after flash the umt .Here is the log.
Device : Nokia TA-1011
Operation : Read Information
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM11)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1009600 [8909] 00000000
OPK_DATA : A57FDEEB0D02233786D8DDCA8A9889D62F92D43EE56EAC9966 024663C39A5B06
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8909_051]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8909, eMMC, 8 GB
LU Count : 1 [0x00E90000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : FIH FIH-E1M-FIH [msm8909] [E1M]
Software : 00WW_1_15P, 00WW_1_15P [Thu Oct 11 20:11:59 CST 2018]
Android Ver. : 8.1.0
Patch Level : 2018-10-01
USERDATA : Normal
You can use RESET LOCKS to remove Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 4.5
now i flash with Nokia__Dynamo_00WW__E1M__600WW Using Infinity best Nk2 device again won't turn on. please help me.
now device not connect in edl 9008 qdloader port. device connect in Diagnostic port 900E
How to recover Qualcomm qdloader 9008 port Again
Please Help me. it ll be humble Thanks.
Last edited:
