Selected model: Infinix X6525B (Infinix Smart 8 Pro)
Operation: Flash (Upgrade)
Software version: 7.5
If BROM was disabled and you want write preloader partition not compatible for this model, phone will bricked. Recovery possible only with ISP mode.
Continue? YES
Parse scatter file... OK
Load Rom Images... OK
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM_V1632 (Android),usb2ser.sys,3.0.1504.0]
Device found at COM114 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0x4D1EB592, 0x2DB6099F, 0xA0AFB138, 0x409DD7EF
Load DownloadAgent... OK
Search DA... OK [0]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [PRELOADER]
Preloader alive. Skip initializing external RAM
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: A3A562
EMMC_ID : 0xD6010341334135363211033E38D01B45
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x1CCF000000 (115.23Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Get scatter info... OK
Checking USB status... USB_HIGH_SPEED
[EFUSE INFO]: BROM not disabled
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EROFS] ... OK
Product Brand : Infinix
Product Manufacturer : INFINIX
Product Model : Infinix X6525B
Product Name : X6525B-OP
Product Device : Infinix-X6525B
Product Board : Infinix-X6525B
Board Platform : mt6765
Build ID : SP1A.210812.016
Build Date : Mon Mar 18 18:27:48 CST 2024
Display ID : INFINIX-TGo-64-240318V979
Security Patch : 2024-03-05
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : 240316V843
Userdata FS Type : F2FS
Switch to BROM
Read partition "preloader"... OK
Read partition "preloader_backup"... OK
Parse scatter file... OK
Load Rom Images... OK
Parse scatter file... OK
Load Rom Images... OK
Connect Type-C to NONE... OK
Connect phone to [PC] in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM115 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM115 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x4D1EB592, 0x2DB6099F, 0xA0AFB138, 0x409DD7EF
Get Chip ID... [MT6765]
Get SOC ID... [DD900FCB5E9C636BA366CF487661BA3A529031C11AE196F98143BDD9B513D81E]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0xD6010341334135363211033E38D01B45
Load EMI config from preloader... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: A3A562
EMMC_ID : 0xD6010341334135363211033E38D01B45
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x1CCF000000 (115.23Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: info not available
Get scatter info... OK
Checking USB status... USB_HIGH_SPEED
Restore parts:
Write file "preloader_x6525b_v659.bin"... OK
Prepare list for upgrade... OK
Checking upgrade list... OK
Prepare format list... OK
Prepare final partition list... OK
Read partition "preloader"... OK
Read partition "proinfo"... OK
Read partition "nvcfg"... OK
Read partition "protect1"... OK
Read partition "protect2"... OK
Read partition "persist"... OK
Read partition "nvram"... OK
Verify checksum... OK
Format "EMMC_USER" partition( 0x00008000..0x00107FFF )... OK
Format "EMMC_USER" partition( 0x00408000..0x01987FFF )... OK
Format "EMMC_USER" partition( 0x03988000..0x0B021FFF )... OK
Format "EMMC_USER" partition( 0x0C800000..0x0CFFFFFF )... OK
Format "EMMC_USER" partition( 0x10000000..0x101FFFFF )... OK
Format "EMMC_USER" partition( 0x14800000..0x1CCB4F7FFF )... OK
Get scatter info... OK
Verify scatter file... OK
Do NAND BMT remark... OK
Setup download info... OK
Get partition table catagory... OK [GPT]
Read mirror partition table... OK
Checking partition table layout changed... OK
Read major partition table... OK
Checking major partition table layout changed... OK
Download "preloader"... OK "preloder_backup"... OK
Download "md1img_a"... OK
Download "spmfw_a"... OK
Download "scp_a"... OK
Download "sspm_a"... OK
Download "gz_a"... OK
Download "lk_a"... OK
Download "logo_a"... OK
Download "boot_a"... OK
Download "dtbo_a"... OK
Download "tee_a"... OK
Download "tkv_a"... OK
Download "vbmeta_a"... OK
Download "vbmeta_system_a"... OK
Download "vbmeta_vendor_a"... OK
Download "logo_b"... OK
Download "super"... OK
Download "tranfs"... OK
Download "userdata"... OK
Read partitions info from phone... OK
Checking A/B state... OK
Flashing done!
Operation: Flash (Upgrade)
Software version: 7.5
If BROM was disabled and you want write preloader partition not compatible for this model, phone will bricked. Recovery possible only with ISP mode.
Continue? YES
Parse scatter file... OK
Load Rom Images... OK
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM_V1632 (Android),usb2ser.sys,3.0.1504.0]
Device found at COM114 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0x4D1EB592, 0x2DB6099F, 0xA0AFB138, 0x409DD7EF
Load DownloadAgent... OK
Search DA... OK [0]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [PRELOADER]
Preloader alive. Skip initializing external RAM
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: A3A562
EMMC_ID : 0xD6010341334135363211033E38D01B45
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x1CCF000000 (115.23Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Get scatter info... OK
Checking USB status... USB_HIGH_SPEED
[EFUSE INFO]: BROM not disabled
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EROFS] ... OK
Product Brand : Infinix
Product Manufacturer : INFINIX
Product Model : Infinix X6525B
Product Name : X6525B-OP
Product Device : Infinix-X6525B
Product Board : Infinix-X6525B
Board Platform : mt6765
Build ID : SP1A.210812.016
Build Date : Mon Mar 18 18:27:48 CST 2024
Display ID : INFINIX-TGo-64-240318V979
Security Patch : 2024-03-05
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : 240316V843
Userdata FS Type : F2FS
Switch to BROM
Read partition "preloader"... OK
Read partition "preloader_backup"... OK
Parse scatter file... OK
Load Rom Images... OK
Parse scatter file... OK
Load Rom Images... OK
Connect Type-C to NONE... OK
Connect phone to [PC] in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM115 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM115 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x4D1EB592, 0x2DB6099F, 0xA0AFB138, 0x409DD7EF
Get Chip ID... [MT6765]
Get SOC ID... [DD900FCB5E9C636BA366CF487661BA3A529031C11AE196F98143BDD9B513D81E]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0xD6010341334135363211033E38D01B45
Load EMI config from preloader... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: A3A562
EMMC_ID : 0xD6010341334135363211033E38D01B45
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x1CCF000000 (115.23Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: info not available
Get scatter info... OK
Checking USB status... USB_HIGH_SPEED
Restore parts:
Write file "preloader_x6525b_v659.bin"... OK
Prepare list for upgrade... OK
Checking upgrade list... OK
Prepare format list... OK
Prepare final partition list... OK
Read partition "preloader"... OK
Read partition "proinfo"... OK
Read partition "nvcfg"... OK
Read partition "protect1"... OK
Read partition "protect2"... OK
Read partition "persist"... OK
Read partition "nvram"... OK
Verify checksum... OK
Format "EMMC_USER" partition( 0x00008000..0x00107FFF )... OK
Format "EMMC_USER" partition( 0x00408000..0x01987FFF )... OK
Format "EMMC_USER" partition( 0x03988000..0x0B021FFF )... OK
Format "EMMC_USER" partition( 0x0C800000..0x0CFFFFFF )... OK
Format "EMMC_USER" partition( 0x10000000..0x101FFFFF )... OK
Format "EMMC_USER" partition( 0x14800000..0x1CCB4F7FFF )... OK
Get scatter info... OK
Verify scatter file... OK
Do NAND BMT remark... OK
Setup download info... OK
Get partition table catagory... OK [GPT]
Read mirror partition table... OK
Checking partition table layout changed... OK
Read major partition table... OK
Checking major partition table layout changed... OK
Download "preloader"... OK "preloder_backup"... OK
Download "md1img_a"... OK
Download "spmfw_a"... OK
Download "scp_a"... OK
Download "sspm_a"... OK
Download "gz_a"... OK
Download "lk_a"... OK
Download "logo_a"... OK
Download "boot_a"... OK
Download "dtbo_a"... OK
Download "tee_a"... OK
Download "tkv_a"... OK
Download "vbmeta_a"... OK
Download "vbmeta_system_a"... OK
Download "vbmeta_vendor_a"... OK
Download "logo_b"... OK
Download "super"... OK
Download "tranfs"... OK
Download "userdata"... OK
Read partitions info from phone... OK
Checking A/B state... OK
Flashing done!