★★ Post Here All Successful Stories By Infinity-Box CM/CM2- ★★

[maanarman]

Qmobile T50 Remove Pattern With Cm2

Set mode to : SP [SC7715] eMMC [Generic]

Operation : Check/Read Info [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7715 eMMC loader v1.1 Inf     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ...

Model Name  : QMobile
Model Brand : QMobile
Model Device: QMobile
AndrVersion : 4.4.3
BaseBand CPU: SCX15_SP7715EA
CompileDate : 8/15/2015 7:10:18 AM
Project Ver : QMobileT50_MP_15_08
Model Ext   : QMobile T50

ExtraInfo : HWInfo exists!!! This phone have DYNAMIC HW settings!!!

Elapsed: 00:00:17

Reconnect Power/Cable!

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7715 eMMC loader v1.1 Inf     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size  : 0x00000000671FB000
State : 0x0001

Mount : /cache
Size  : 0x0000000003200000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Done!

Elapsed: 00:00:18

Reconnect Power/Cable!

 

[maanarman]

Motorola Turbo FRP Remove With Cm2

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:01:58

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : quark_verizon
Model  : XT1254
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:10

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:05

 

[maanarman]

Mars 11 Read Flash With Cm2

Info

Set mode to : SP [SC983x] eMMC [Generic Android 7.x]

Operation : Check/Read Info [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC983x eMMC Loader v5.0 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ...

Model Name  : Mars_11
Model Brand : Mars
Model Device: Mars_11
AndrVersion : 6.0
BaseBand CPU: 1491SL_L8
CompileDate : 6/12/2017 9:51:30 AM
Project Ver : MRA58K release-keys
Model Ext   : Mars_11

ExtraInfo : HWInfo not exists, normal phone

Elapsed: 00:00:25

Reconnect Power/Cable!

Read Flash

Operation : Read FullFlash [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC983x eMMC Loader v5.0 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!

[FW_READER] : Prepare Ok!
- > Wait phone connected ...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC983x eMMC Loader v5.0 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

- > Wait phone connected ...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC983x eMMC Loader v5.0 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Model Name  : Mars_11
Model Brand : Mars
Model Device: Mars_11
AndrVersion : 6.0
BaseBand CPU: 1491SL_L8
Project Ver : MRA58K release-keys
Model Ext   : Mars_11

[Read Mode] : HSUSB : 0x3000

[FW_READER] : Reading Firmware Now ...

[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : nvitem_l.bin
[Read Ok] : sharkl_cp1.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : l__WPH_arm7.bin
[Read Ok] : PM_arm7_sys.bin
[Read Ok] : logo_720x1280.bin
[Read Ok] : fblogo_720x1280.bin
[Read Ok] : wcn_fdl.bin
[Read Ok] : AA_MARLIN.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : sysinfo.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img

AndroidInfo created
Firmware Size : 1724 MiB
Saved to : C:\Users\test\Desktop\TEMP\1491SL_L8_Mars_11_6.0_MRA58K_release-keys_Mars_11\
Done!

Elapsed: 00:08:38

Reconnect Power/Cable!

 

[maanarman]

Motorola E4 FRP Remove With Cm2

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:02:43

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : perry_verizon_f
Model  : Moto E (4)
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:13

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:05

 

[maanarman]

Siccoo E801 Read Flash WIth Cm2

SCRD mode : AUTO
SPRD mode : SC6530 : REV : 0000 : NOR


Operation : Read Flash [ v1.02 ]

----- > Powered On :
1. Power On device
2. Connect USB cable
3. When device show StorageMode : Press '0' button for a 5 second!
----- > Powered Off :
1. Insert USB cable
2. Wait when device show Charge icon
3. When device show StorageMode : Press '0' button for a 5 second!

Wait for device ...

Device Connected!
BOOT_PWR0 : 0x00600000
BOOT_INIT : 0x81C0024C
BOOT_MODE : DOWNLOAD
BOOT_INTV : 6533G-FPTRUNK-W16.44.2
InternalVersion: g8bec5c4c
Setting BOOTROM mode
BOOT_MODE : BOOTROM
Boot_CPU  : 0x08090007 : [SPREADTRUM] : SC6533G
MEMD for flsh_spi32m Branch: none
Boot_CS0 : 0x00000000 : SPI : [SPIDEF] : 25Q32 : 0x00400000 [ 4MiB ]
Performing MemoryInit
Selecting RL
Sending RL
Config : MemoryInit
Config : Loader
BOOT_MODE : RLOADER
Boot IV  : 0xFBA2A250
Boot done!

Read done, 0x00400000

Verify FlashContent
MCU verified
CAL verified
FAC verified

Device Info Details :
[0] : sc6533g_XS35_E11_D
[1] : 8809
[2] : 8809e2
[3] : CT8851C
[4] : pasw_hs8292u
[5] : flsh_spi32m
[6] : st7789/gc9304c/gc9305/ili9325/ili9341/gc9306/LGDP4535/nv3029e/r61505u/otm3208/nv3029g/nv3029h
[7] : bf3a01serial/gc6123/gc6133/sp0820
[8] : rdabt_8809
[9] : rdafm_8809e
[10] : release
[11] : 2017-08-31_19:34:36
[12] : E11_D11_SICCOO_S_LG_V26

Saved to : C:\Users\test\Desktop\
Saved as : SC6533G_4MiB_sc6533g_XS35_E11_D_E11_D11_SICCOO_S_LG_V26_2017-08-31_193436.ilod


Done!
Elapsed: 00:00:37

 

[maanarman]

Qmobile K100 Factory Reset With Cm2

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 14 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00EF 0040 0016 0000
[0] Flash VEN : Winbond , W25Q32
[0] Flash CAP : 00400000
Verify data... Can take some time
Init Ok, formatting DIN area ...
Format Block Done!
Done!

Elapsed: 00:00:38

Reconnect Power/Cable!

 

[maanarman]

Motorola Turbo FRP Remove With Cm2

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:02:35

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : quark_verizon
Model  : XT1254
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:11

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:06

 

[maanarman]

Call me C343 Remove Phone Lock With Cm2

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 14 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Verify data... Can take some time
Init Ok, formatting DIN area ...
Format Block Done!
Done!

Elapsed: 00:00:13

Reconnect Power/Cable!

 

[maanarman]

Qmobile M3 Factory Reset With Cm2

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 14 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Verify data... Can take some time
Init Ok, formatting DIN area ...
Format Block Done!
Done!

Elapsed: 00:00:19

Reconnect Power/Cable!

 

[maanarman]

H-Mobile R2 Restart Problem Solve With Cm2

Operation : Reset Settings [ v1.02 ]
----- > Powered On :
1. Power On device
2. Connect USB cable
3. When device show StorageMode : Press '0' button for a 5 second!
----- > Powered Off :
1. Insert USB cable
2. Wait when device show Charge icon
3. When device show StorageMode : Press '0' button for a 5 second!

Wait for device ...

Device Connected!
BOOT_PWR0 : 0x00600000
BOOT_INIT : 0x81C0024C
BOOT_MODE : DOWNLOAD
BOOT_INTV : 6533G-FPTRUNK-W16.44.2
InternalVersion: g8bec5c4c
Setting BOOTROM mode
BOOT_MODE : BOOTROM
Boot_CPU  : 0x08090007 : [SPREADTRUM] : SC6533G
MEMD for flsh_spi32m Branch: none
Boot_CS0 : 0x00000000 : SPI : [SPIDEF] : 25Q32 : 0x00400000 [ 4MiB ]
Performing MemoryInit
Selecting RL
Sending RL
Config : MemoryInit
Config : Loader
BOOT_MODE : RLOADER
Boot IV  : 0xFBA2A250
Boot done!

Preparing PMT
Verifying PMT
Erasing 1474560 bytes

FileSystem format done!


Done!
Elapsed: 00:00:13

Reconnect Power/Cable!

 

[maanarman]

Qmobile K100 Remove Phone Lock With Cm2

Set mode to : SPD6531

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00EF 0040 0016 0000
[0] Flash VEN : Winbond , W25Q32
[0] Flash CAP : 00400000
Verify data... Can take some time
Init Ok, formatting DIN area ...
Format Block Done!
Done!

Elapsed: 00:00:10

Reconnect Power/Cable!

 

[maanarman]

Siccoo E801 Phone Lock Remove With Cm2

Reconnect Power/Cable!

Operation : Reset Settings [ v1.02 ]
----- > Powered On :
1. Power On device
2. Connect USB cable
3. When device show StorageMode : Press '0' button for a 5 second!
----- > Powered Off :
1. Insert USB cable
2. Wait when device show Charge icon
3. When device show StorageMode : Press '0' button for a 5 second!

Wait for device ...

Device Connected!
BOOT_PWR0 : 0x00600000
BOOT_INIT : 0x81C0024C
BOOT_MODE : DOWNLOAD
BOOT_INTV : 6533G-FPTRUNK-W16.44.2
InternalVersion: g8bec5c4c
Setting BOOTROM mode
BOOT_MODE : BOOTROM
Boot_CPU  : 0x08090007 : [SPREADTRUM] : SC6533G
MEMD for flsh_spi32m Branch: none
Boot_CS0 : 0x00000000 : SPI : [SPIDEF] : 25Q32 : 0x00400000 [ 4MiB ]
Performing MemoryInit
Selecting RL
Sending RL
Config : MemoryInit
Config : Loader
BOOT_MODE : RLOADER
Boot IV  : 0xFBA2A250
Boot done!

Preparing PMT
Verifying PMT
Erasing 1474560 bytes

FileSystem format done!


Done!
Elapsed: 00:00:25

Reconnect Power/Cable!

 

[maanarman]

Qmobile E440i Hang Logo Solve With Cm2

Set mode to : SPD6531

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Verify data... Can take some time
Init Ok, formatting DIN area ...
Format Block Done!
Done!

Elapsed: 00:00:10

Reconnect Power/Cable!

 

[maanarman]

H-Mobile R2 Factory Reset With Cm2

Operation : Reset Settings [ v1.02 ]
----- > Powered On :
1. Power On device
2. Connect USB cable
3. When device show StorageMode : Press '0' button for a 5 second!
----- > Powered Off :
1. Insert USB cable
2. Wait when device show Charge icon
3. When device show StorageMode : Press '0' button for a 5 second!

Wait for device ...

Device Connected!
BOOT_PWR0 : 0x00600000
BOOT_INIT : 0x81C0024C
BOOT_MODE : DOWNLOAD
BOOT_INTV : 6533G-FPTRUNK-W16.44.2
InternalVersion: g8bec5c4c
Setting BOOTROM mode
BOOT_MODE : BOOTROM
Boot_CPU  : 0x08090007 : [SPREADTRUM] : SC6533G
MEMD for flsh_spi32m Branch: none
Boot_CS0 : 0x00000000 : SPI : [SPIDEF] : 25Q32 : 0x00400000 [ 4MiB ]
Performing MemoryInit
Selecting RL
Sending RL
Config : MemoryInit
Config : Loader
BOOT_MODE : RLOADER
Boot IV  : 0xFBA2A250
Boot done!

Preparing PMT
Verifying PMT
Erasing 1474560 bytes

FileSystem format done!


Done!
Elapsed: 00:00:13

Reconnect Power/Cable!

 

[maanarman]

Oale X1 Phone Lock Remove With Cm2

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : F40122426977696E20103237313664AF
[WARNING] : MEMORY_eMMC_VALIDATE_FAILED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0xF4 , OEM : 0122
[eMMC] : FLASH_INF : [NOT_IN_BASE] , niwi
[eMMC] : FLASH_CID : F40122426977696E20103237313664AF
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001CD000000
[eMMC] : FLASH_UCP : 7376 MiB [eMMC 8 GiB]
DEV RID    : 0x644765A70810E7D3B77C912E2C03E6B6
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : alps
ProdName  : full_gxq6580_weg_l
ProdModel : gxq6580_weg_l
Device    : gxq6580_weg_l
AndroidVer: 5.1
MTKxCPU   : MT6580
MTKxPRJ   : ALPS.L1.MP6.V2_GXQ6580.WEG.L_P69

Done!
Elapsed: 00:00:16
Reconnect Power/Cable!

Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : F40122426977696E20103237313664AF
[WARNING] : MEMORY_eMMC_VALIDATE_FAILED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0xF4 , OEM : 0122
[eMMC] : FLASH_INF : [NOT_IN_BASE] , niwi
[eMMC] : FLASH_CID : F40122426977696E20103237313664AF
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001CD000000
[eMMC] : FLASH_UCP : 7376 MiB [eMMC 8 GiB]
DEV RID    : 0x644765A70810E7D3B77C912E2C03E6B6
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!
Clear DIN
Clear Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:49
Reconnect Power/Cable!

 

[maanarman]

Samsung J327vpp Write Flash With Cm2

Port open Ok!
LOKE received!
Prepare Ok!
Enter Setup...
Setup Done!
Try download PIT...
Download PIT Ok!
Start flashing!

Flashing aboot.mbn
Flashing sbl1.mbn
Flashing rpm.mbn
Flashing tz.mbn
Flashing devcfg.mbn
Flashing NON-HLOS.bin
Flashing cmnlib.mbn
Flashing keymaster.mbn
Flashing lksecapp.mbn
Flashing sec.dat
Flashing apdp.mbn
Flashing msadp.mbn
Flashing boot.img
Flashing recovery.img
Flashing system.img.ext4
Flashing persist.img.ext4
Flashing userdata.img.ext4
Flashing modem.bin
Flashing adspso.bin
Flashing cache.img.ext4
Flashing done

Reboot phone...


Phone Disconnected

 

[maanarman]

Qmobile D2 Factory Reset With Cm2

SCRD mode : AUTO
SPRD mode : SC6530 : REV : 0000 : NOR


SPRD mode : SC6531 : REV : E000 : NOR

Operation : Format FileSystem [ v1.02 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
BootSource  :  InternalLibrary
BootVersion : Infinity SCR SC6531E Loader v 1.2
Port speed : 921600
FDL Flash  : Control transfered!

Boot Done!

CS0_MEM : SPI : [WINBOND] : W25Q32 : 0x00400000 [ 4MiB ]

Make backup of sensetive data
Backup saved to : C:\InfinityBox\CM2SCR\Backup\00400000_FMT_BACK_098D7700184D_NVM.nv

Executing FormatFFS ...
Format FFS Done!

Done!
Elapsed: 00:00:16

Reconnect Power/Cable!

 

[maanarman]

Samsung J327p Write Flash Done

Port open Ok!
LOKE received!
Prepare Ok!
Enter Setup...
Setup Done!
Try download PIT...
Download PIT Ok!
Start flashing!

Flashing aboot.mbn
Flashing sbl1.mbn
Flashing rpm.mbn
Flashing tz.mbn
Flashing devcfg.mbn
Flashing NON-HLOS.bin
Flashing cmnlib.mbn
Flashing keymaster.mbn
Flashing lksecapp.mbn
Flashing sec.dat
Flashing apdp.mbn
Flashing msadp.mbn
Flashing boot.img
Flashing recovery.img
Flashing system.img.ext4
Flashing persist.img.ext4
Flashing modem.bin
Flashing adspso.bin
Flashing cache.img.ext4
Flashing done

Reboot phone...


Phone Disconnected

 

[maanarman]

Gfive Hero Factory Reset With Cm2

SPRD mode : SC6531 : REV : E000 : NOR

Operation : Format FileSystem [ v1.02 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
BootSource  :  InternalLibrary
BootVersion : Infinity SCR SC6531E Loader v 1.2
Port speed : 921600
FDL Flash  : Control transfered!

Boot Done!

CS0_MEM : SPI : [WINBOND] : W25Q32 : 0x00400000 [ 4MiB ]

Make backup of sensetive data
Backup saved to : C:\InfinityBox\CM2SCR\Backup\00400000_FMT_BACK_025EFD22791B_NVM.nv

Executing FormatFFS ...
Format FFS Done!

Done!
Elapsed: 00:00:33

Reconnect Power/Cable!

 

[maanarman]

Qmobile R2000 Factory Reset With Cm2

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 102 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0018 0000
[0] Flash VEN : GigaDevice , GD25LQ128
[0] Flash CAP : 01000000
Verify data... Can take some time
Init Ok, formatting DIN area ...
Format Block Done!
Done!

Elapsed: 00:00:47

Reconnect Power/Cable!