★★ Post Here All Successful Stories By Infinity-Box CM/CM2- ★★

[maanarman]

Moto G4 Play FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1609
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1609
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1609
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:01:56

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : harpia_vzw
Model  : XT1609
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:12

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:07

 

[maanarman]

Moto E4 FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:00:59

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : perry_verizon_f
Model  : Moto E (4)
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:11

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:06

 

[maanarman]

Lenovo A328 Read Pattern Done

Operation : Read Pattern/DP Lock [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 47 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A483447316404050DA2F73912FD
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A483447316404050DA2F73912FD
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID    : 0x644765A72A428FF5ED3AD0C00F35A135
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading data ...

Get Locks ...
PatternLock Sequnce : 456982

Done!
Elapsed: 00:00:15
Reconnect Power/Cable!

 

[maanarman]

Moto E4 FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:01:01

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : perry_verizon_f
Model  : Moto E (4)
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:23

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:06

 

[maanarman]

Moto G4 Play FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1609
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1609
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1609
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:02:23

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : harpia_vzw
Model  : XT1609
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:19

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:10

 

[maanarman]

Qmobile X2 Hang Logo Done With Cm2

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6571
BB_CPU_NME : [MediaTek] MT6571_S00
BB_CPU_EXT : 0xCA00 , 0x8D00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8B
NAND Flash : 009800BC009000660076001600080000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0011 , [KINGSTON] KTN0403CS_TCR1
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0016 0008
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
DEV RID    : 0x644765A77B010123747632A8BC8DF71C
INT RAM    : 0x00020000
EXT RAM    : 0x10000000 [256 MiB]
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : QMobile
ProdName  : s3510ap
ProdModel : QMobile X2
Device    : s3510ap
AndroidVer: 4.4.2
MTKxCPU   : MT6571
MTKxPRJ   : ALPS.KK1.MP7.V1

Done!
Elapsed: 00:00:12
Reconnect Power/Cable!

Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6571
BB_CPU_NME : [MediaTek] MT6571_S00
BB_CPU_EXT : 0xCA00 , 0x8D00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8B
NAND Flash : 009800BC009000660076001600080000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0011 , [KINGSTON] KTN0403CS_TCR1
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0016 0008
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
DEV RID    : 0x644765A77B010123747632A8BC8DF71C
INT RAM    : 0x00020000
EXT RAM    : 0x10000000 [256 MiB]
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:14
Reconnect Power/Cable!

 

[maanarman]

Motorola Turbo FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:02:08

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : quark_verizon
Model  : XT1254
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:11

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:06

 

[maanarman]

Motorola Xt1527 FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1527
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1527
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1527
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:01:57

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : surnia_att
Model  : MotoE2(4G-LTE)
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:12

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:09

 

[maanarman]

Motorola Turbo FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:00:32

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : quark_verizon
Model  : XT1254
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:11

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:04

 

[maanarman]

Samsung j327vpp write Flash Done

Port open Ok!
LOKE received!
Prepare Ok!
Enter Setup...
Setup Done!
Try download PIT...
Download PIT Ok!
Start flashing!

Flashing aboot.mbn
Flashing sbl1.mbn
Flashing rpm.mbn
Flashing tz.mbn
Flashing devcfg.mbn
Flashing NON-HLOS.bin
Flashing cmnlib.mbn
Flashing keymaster.mbn
Flashing lksecapp.mbn
Flashing sec.dat
Flashing apdp.mbn
Flashing msadp.mbn
Flashing boot.img
Flashing recovery.img
Flashing system.img.ext4
Flashing persist.img.ext4
Flashing userdata.img.ext4
Flashing modem.bin
Flashing adspso.bin
Flashing cache.img.ext4
Flashing done

Reboot phone...


Phone Disconnected

 

[maanarman]

Qmobile i6 metel one frp remove cm2

Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4838473165050731D6C442832F
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e1G8
[eMMC] : FLASH_CID : 90014A4838473165050731D6C442832F
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0x644765A75255FA1BB0379685CCD34B5E
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!
Clear DIN
Clear Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:47
Reconnect Power/Cable!

 

[maanarman]

Qmobile X6 Hang Logo Done

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6571
BB_CPU_NME : [MediaTek] MT6571_S00
BB_CPU_EXT : 0xCA00 , 0x8D00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8B
NAND Flash : 009800BC009000660076001600080000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0011 , [KINGSTON] KTN0403CS_TCR1
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0016 0008
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
DEV RID    : 0x644765A7CA7E018C13A436687AA25C80
INT RAM    : 0x00020000
EXT RAM    : 0x10000000 [256 MiB]
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : QMobile
ProdName  : QMobile X6
ProdModel : QMobile X6
Device    : QMobile X6
AndroidVer: 4.4.2
MTKxCPU   : MT6571
MTKxPRJ   : ALPS.KK1.MP7.V1

Done!
Elapsed: 00:00:10
Reconnect Power/Cable!

Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6571
BB_CPU_NME : [MediaTek] MT6571_S00
BB_CPU_EXT : 0xCA00 , 0x8D00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8B
NAND Flash : 009800BC009000660076001600080000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0011 , [KINGSTON] KTN0403CS_TCR1
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0016 0008
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
DEV RID    : 0x644765A7CA7E018C13A436687AA25C80
INT RAM    : 0x00020000
EXT RAM    : 0x10000000 [256 MiB]
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:13
Reconnect Power/Cable!

 

[maanarman]

Motorola Turbo FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:01:51

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : quark_verizon
Model  : XT1254
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:16

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:06

 

[maanarman]

Motorola Xt1565 FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...

1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!

Connect Ok!

Waiting ...
Trying link with  : 192.168.137.2
Connected to device!

Device : XT1565
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!

Trying link with  : 192.168.137.2
Connected to device!

Device : XT1565
Setting ADB ...
Waiting device ...
Connect Ok!

Trying link with  : 192.168.137.2
Connected to device!

Device : XT1565
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:00:53

Operation : Reset FRP (ADB) [ v1.03 ]

Waiting for device in ADB mode ...

1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!

Connect Ok!

Device : lux_verizon
Model  : XT1565
FRP reset passed! Make FACTORY RESET from menu!

-- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!


Done!
Elapsed: 00:00:11

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...

1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!

Connect Ok!

Operation done!



Done!
Elapsed: 00:00:04

 

[maanarman]

Moto E4 FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1767
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:01:25

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Device not found! Check cable, drivers and conection!
 
Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : perry_verizon_f
Model  : Moto E (4)
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:11

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:07

 

[maanarman]

Samsung J727vpp FRP Bypass Done

Connect ADB - Ok

Model - SM-J727V
Product - j7popltevzw
CPU - MSM8953
Phone version - FA70_J727VVRU1ARB1
Android version - 7.0
CSC country code -
CSC sales  code -
Phone serial No - R28J810983K
Phone SIM Slot count - 1
Phone IMEI -  Not readed
Phone not Rooted



Connect ADB - Ok

Reset FRP/ REACTIVATION LOCK - Done
Reboot Phone...


Phone Disconnected

 

[maanarman]

Qmobile Metal One FRP Remove Done

Set mode to : SP [SC773x] eMMC [Android 6.x]

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size  : 0x0000000117FF7000
State : 0x0001

Mount : /cache
Size  : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x/6.x : Reset FRP Lock
Reset Ok!


Done!

Elapsed: 00:00:20

Reconnect Power/Cable!

 

[maanarman]

Samsug G550t Write Flash Done

Port open Ok!
LOKE received!
Prepare Ok!
Enter Setup...
Setup Done!
Try download PIT...
Download PIT Ok!
Start flashing!

Flashing sboot.bin
Flashing param.bin
Flashing boot.img
Flashing recovery.img
Flashing system.img
Flashing modem.bin
Flashing done

Reboot phone...


Phone Disconnected

 

[maanarman]

M-Horse S12 Remove Lock Done

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : 00AD00BC00900055005400AD00BC0000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x008B , [HYNIX] H9DA4VH2GJAMCR_4EM
[NAND] : FLASH_DIE : 00AD 00BC 0090 0055 0054 00AD 00BC
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 0800/0040/01/NIM_Px-2
DEV RID    : 0x644765A7E0EED4ADC880E43AA704E10D
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : S12
ProdName  : S12
ProdModel : S12
AndroidVer: 5.1
MTKxCPU   : MT6572
MTKxPRJ   : MP.V1.0

Done!
Elapsed: 00:00:12
Reconnect Power/Cable!

Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : 00AD00BC00900055005400AD00BC0000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x008B , [HYNIX] H9DA4VH2GJAMCR_4EM
[NAND] : FLASH_DIE : 00AD 00BC 0090 0055 0054 00AD 00BC
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 0800/0040/01/NIM_Px-2
DEV RID    : 0x644765A7E0EED4ADC880E43AA704E10D
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:13
Reconnect Power/Cable!

 

[maanarman]

Motorola Turbo FRP Remove Done

Operation : Moto ADB Enable [ v1.03 ]
Mode : Enable ADB
Waiting for NetInterface arrival ...
 
1. Power off device. Press and hold 'VOL DOWN' and 'POWER ON' buttons
2. Select by 'VOL DOWN' or 'VOL UP' FACTORY MODE , press 'POWER ON'
3. Connect USB cable, when device boot complete!
 
Connect Ok!
 
Waiting ...
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Switching to FACTORY ...
Setting Unsecure mode
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...
Waiting device ...
Connect Ok!
 
Trying link with  : 192.168.137.2
Connected to device!
 
Device : XT1254
Setting ADB ...

1. Disconnect cable from device, wait device reboot
2. Make "Reset FRP"
3. Disable "FACTORY MODE" after operations done!


Done!
Elapsed: 00:01:45

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ...
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : quark_verizon
Model  : XT1254
FRP reset passed! Make FACTORY RESET from menu!
 
 -- > MOTO FRP : Don't forget to DISABLE FACTORY MODE!
 

Done!
Elapsed: 00:00:11

Operation : Moto ADB Enable [ v1.03 ]
Mode : Disable Factory
Waiting for device in fastboot mode ...
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
Operation done!
 


Done!
Elapsed: 00:00:06