★★ Post Here All Successful Stories By BB5 Easy Service Tool (BEST) Nokia Dongle ★★
★★ Post Here All Successful Stories By BB5 Easy Service Tool (BEST) Nokia Dongle ★★
- Thread starter Forum Supporter
- Start date
Nokia-130 RM-1035 MT6260
Stuck On Logo Solved
http://i288.photobucket.com/albums/ll184/Martview_Forum/Nokia-130_zpsi2gjhpy4.png
Code:
Connect phone on selected interface...
Core : v2.25 , MTKx FlashEngine : v10.5
Verify files ...
MAUI : RM-1035_ROM_eMP_11.00.11
VIVA : RM-1035_VIVA_eMP_11.00.11
LANG : RM-1035_LANG_PACK_ROM_IM_eMP_11.00.11_002
CUST : RM-1035_CUSTPACK_ROM_IM_MEA_BH_eMP_11.00.11_002
JMPT : RM-1035_JUMP_TABLE_IM_MEA_BH_eMP_11.00.11_002
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 27 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 6D789A1334F3AB7D14CDEA99132466C1
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : CRYSTAL.10.01.11.p2
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Crystal.fg
DA_VERIFY : 00
DA_JUMP : 00040000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A4000-0x003F3FFF , LEN : 0x00050000
SecureDecrypt : RM-1035_ROM_eMP_11.00.11
SecureDecrypt : RM-1035_VIVA_eMP_11.00.11
SecureDecrypt : RM-1035_LANG_PACK_ROM_IM_eMP_11.00.11_002
SecureDecrypt : RM-1035_CUSTPACK_ROM_IM_MEA_BH_eMP_11.00.11_002
SecureDecrypt : RM-1035_JUMP_TABLE_IM_MEA_BH_eMP_11.00.11_002
OVRLP : 000069B900000001
PHPID : CRYSTAL.10.01.11.p2
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-1035_ROM_eMP_11.00.11
Write : RM-1035_LANG_PACK_ROM_IM_eMP_11.00.11_002
Write : RM-1035_CUSTPACK_ROM_IM_MEA_BH_eMP_11.00.11_002
Write : RM-1035_JUMP_TABLE_IM_MEA_BH_eMP_11.00.11_002
Write : RM-1035_VIVA_eMP_11.00.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-1035_ROM_eMP_11.00.11
[VERIFY] DONE : RM-1035_LANG_PACK_ROM_IM_eMP_11.00.11_002
[VERIFY] DONE : RM-1035_CUSTPACK_ROM_IM_MEA_BH_eMP_11.00.11_002
[VERIFY] DONE : RM-1035_JUMP_TABLE_IM_MEA_BH_eMP_11.00.11_002
[VERIFY] DONE : RM-1035_VIVA_eMP_11.00.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x003A4000-0x003F3FFF , LEN : 0x00050000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Rebooting phone now
Flashing done!
Total flash time : 00:00:58
Reboot phone Ok
Connect phone on selected interface...
HDM Global Nokia 150 ( RM-1189 and RM-1190 ) supported with BEST.
Download Firmware :
Code:
SSChannel : Create SC
SSChannel : SC Created!
ProductID HWCode : RM-1190
Selected Variant : RM-1190 NDT EURO EI WHITE CYRILLIC RU
Firmware Version : 10.02.11
Platform Version : S30+
SSChannel : DC Ok with code 0x0A
Switch to IDM now ...
IDM initializing, wait...
Checking access to Products folder...
Folder for RM-1190 exist
Prepare done, collect info
[Query] : RM1190_059X8V9_10.02.11_001.vpl , 5,96 KiB
[Query] : RM-1190_auth_sv5_eMP.auth , 2,20 KiB
[Query] : RM-1190_CUSTPACK_ROM_EI_EURO_RU_eMP_10.02.11_001 , 75,67 KiB
[Query] : RM-1190_EXT_BOOTLOADER_eMP_10.02.11 , 79,90 KiB
[Query] : RM-1190_JUMP_TABLE_EI_EURO_RU_eMP_10.02.11_001 , 1,15 KiB
[Query] : RM-1190_LANG_PACK_ROM_EI_eMP_10.02.11_001 , 254,18 KiB
[Query] : RM-1190_ROM_eMP_10.02.11 , 551,46 KiB
[Query] : RM-1190_ROOTCERT_Signed_By_MTK_eMP_10.02.11 , 1,32 KiB
[Query] : RM-1190_SECURE_RO_ME_eMP_10.02.11 , 1,59 KiB
[Query] : RM-1190_VIVA_eMP_10.02.11 , 2,39 MiB
Files to download : 10
Total size to download : 3,34 MiB
Downloading now, please, wait...
[Download] : RM1190_059X8V9_10.02.11_001.vpl
[Skip,Exist] : RM-1190_auth_sv5_eMP.auth
[Skip,Exist] : RM-1190_CUSTPACK_ROM_EI_EURO_RU_eMP_10.02.11_001
[Skip,Exist] : RM-1190_EXT_BOOTLOADER_eMP_10.02.11
[Skip,Exist] : RM-1190_JUMP_TABLE_EI_EURO_RU_eMP_10.02.11_001
[Skip,Exist] : RM-1190_LANG_PACK_ROM_EI_eMP_10.02.11_001
[Skip,Exist] : RM-1190_ROM_eMP_10.02.11
[Skip,Exist] : RM-1190_ROOTCERT_Signed_By_MTK_eMP_10.02.11
[Skip,Exist] : RM-1190_SECURE_RO_ME_eMP_10.02.11
[Skip,Exist] : RM-1190_VIVA_eMP_10.02.11
Verify files now ...
[Verify Ok] : RM-1190_ROOTCERT_Signed_By_MTK_eMP_10.02.11
[Verify Ok] : RM-1190_EXT_BOOTLOADER_eMP_10.02.11
[Verify Ok] : RM-1190_SECURE_RO_ME_eMP_10.02.11
[Verify Ok] : RM-1190_ROM_eMP_10.02.11
[Verify Ok] : RM-1190_LANG_PACK_ROM_EI_eMP_10.02.11_001
[Verify Ok] : RM-1190_CUSTPACK_ROM_EI_EURO_RU_eMP_10.02.11_001
[Verify Ok] : RM-1190_JUMP_TABLE_EI_EURO_RU_eMP_10.02.11_001
[Verify Ok] : RM-1190_VIVA_eMP_10.02.11
[Verify Ok] : RM-1190_auth_sv5_eMP.auth
All done, all files were downloaded!
Firmware flashing :
Code:
Core : v2.27 , MTKx FlashEngine : v11.5
Verify files ...
MAUI : RM-1190_ROM_eMP_10.02.11
VIVA : RM-1190_VIVA_eMP_10.02.11
LANG : RM-1190_LANG_PACK_ROM_EI_eMP_10.02.11_001
CUST : RM-1190_CUSTPACK_ROM_EI_EURO_RU_eMP_10.02.11_001
JMPT : RM-1190_JUMP_TABLE_EI_EURO_RU_eMP_10.02.11_001
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 26 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 65BD69193D6263B762Axxxxxxxxx
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : DUBAI61D.10.02.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Dubai.fg
DA_VERIFY : 00
DA_JUMP : 00100000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00EC , [GigaDevice] GD25LQ32
[0] : FLASH_DIE : 00C8 0060 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A0000-0x003F7FFF , LEN : 0x00058000
SecureDecrypt : RM-1190_ROM_eMP_10.02.11
SecureDecrypt : RM-1190_VIVA_eMP_10.02.11
SecureDecrypt : RM-1190_LANG_PACK_ROM_EI_eMP_10.02.11_001
SecureDecrypt : RM-1190_CUSTPACK_ROM_EI_EURO_RU_eMP_10.02.11_001
SecureDecrypt : RM-1190_JUMP_TABLE_EI_EURO_RU_eMP_10.02.11_001
OVRLP : 000069B900000001
PHPID : DUBAI61D.10.02.11.p1
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-1190_ROM_eMP_10.02.11
Write : RM-1190_LANG_PACK_ROM_EI_eMP_10.02.11_001
Write : RM-1190_CUSTPACK_ROM_EI_EURO_RU_eMP_10.02.11_001
Write : RM-1190_JUMP_TABLE_EI_EURO_RU_eMP_10.02.11_001
Write : RM-1190_VIVA_eMP_10.02.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-1190_ROM_eMP_10.02.11
[VERIFY] DONE : RM-1190_LANG_PACK_ROM_EI_eMP_10.02.11_001
[VERIFY] DONE : RM-1190_CUSTPACK_ROM_EI_EURO_RU_eMP_10.02.11_001
[VERIFY] DONE : RM-1190_JUMP_TABLE_EI_EURO_RU_eMP_10.02.11_001
[VERIFY] DONE : RM-1190_VIVA_eMP_10.02.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x003A0000-0x003F7FFF , LEN : 0x00058000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Rebooting phone now
Flashing done!
Total flash time : 00:01:01
Reboot phone Ok
- > Hint : If phone shows Battery charge icon - press and hold PowerOn button 10 seconds
Wait, when phone will be ready ...
Reading Phone Info....
Software Info: 10.02.11 00-00-00 RM-1190
IMEI: 3548870xxxxxxxxx
Ape Version: NEMO G 59cb152c/0 (59cb152c+0) T Mon Jul 1 02:50:44 2013 U 69b804d5
PPM version : EI
Product code: 059X8V8
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Connect phone on selected interface...
Identify :
Code:
Phone found!
MTKx Nokia Phone detected
Read info... Ok
Reading Phone Info....
Software ver : 10.02.11 00-00-00 RM-1190
IMEI 1 : 3548870xxxxxxx
IMEI 2 : 3548870xxxxxxx
XappVer : 000008DE
Ape Ver : NEMO G 59cb152c/0 (59cb152c+0) T Mon Jul 1 02:50:44 2013 U 69b804d5
PPM : EI
CNT : DUBAI61D.10.02.11.p1
Product SN : F85AB38AU
Product code : 059X8V8
Base Prd.code: 059X7J5
Module code : 0207092
Hardware info=======
HWID : 1100
LCDVer: TPO
Lock info ===========
IMEI : 3548870xxxxxx
IMEI spNet : 3A 45 88 xxxx xxxx
Conf key : 800000000004000B
Provider key : 2440700000000000
Country : Finland
Operator : NOKIA (Open)
Lock info:
Block 1
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 2
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 3
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 4
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 5
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 6
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 7
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
SimLock status : Ok
Security status : Ok
Done!
SelfTest :
Code:
Execuring SelfTests
Passed : Camera_If Test
Passed : Display Test
Passed : Keyboard_Short_Circuit Test
Passed : MicroSD_Short_Circuit Test
Passed : Sim_Short_Circuit Test
Passed : Real_Time_Clock Test
Passed : Bluetooth Test
Passed : Audio Test
Passed : Charge Test
Passed : Earpiece Test
Done
Format FS / Reset Settings :
Code:
Software Info: 10.02.11 00-00-00 RM-1190
IMEI: 3548870xxxxxx
PPM version : EI
Product code: 059X8V8
Rebooting phone to FlashMode...
Wait for phone...
Phone found! [ 26 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 65BD69193D6263B7xxxxxxxxxxxxx
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : DUBAI61D.10.02.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Dubai.fg
DA_VERIFY : 00
DA_JUMP : 00100000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00EC , [GigaDevice] GD25LQ32
[0] : FLASH_DIE : 00C8 0060 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A0000-0x003F7FFF , LEN : 0x00058000
Executing FFS FORMAT now...
FAT_RANGE : 0x003A0000-0x003F7FFF , LEN : 0x00058000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Elapsed: 00:00:16
Connect phone on selected interface...
Backup RPL :
Code:
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 26 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 65BD69193D6263B76xxxxxxxxxxxxx
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : DUBAI61D.10.02.11.p1
BROM/BL stage done
Configure RAMINIT Ok
Reading flash now ...
Done!
Control Block Validation (Security Test) :
CBR is Ok, match with BB SN. Phone Security is Alive
Mobile Info
IMEI : 354887081481584
BBUID : 65BD69193D6263B76xxxxxxxxxxxx
PCCode: 059X8V8
SimLock Info :
STATE : OPENED ( NOT LOCKED )
RPL Saved to : 3548870xxxxxxx_MTKx_2nd.mtsec
Read Done!
Connect phone on selected interface...
Write RPL ( with additional fix/edit/repair operations ) :
Code:
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 26 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 65BD69193D6263B76xxxxxxx
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : DUBAI61D.10.02.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Dubai.fg
DA_VERIFY : 00
DA_JUMP : 00100000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00EC , [GigaDevice] GD25LQ32
[0] : FLASH_DIE : 00C8 0060 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A0000-0x003F7FFF , LEN : 0x00058000
Boot Ok
Get settings...
[INFO] : Encrypted RPL
[RPL VERIFY] : Code 0x10 : MOBILE_ID match with MOBILE_ID info in RPL!
Reset SimLock Counters
Reset SimLock Counters Done!
DSPhone : LifeTimer not exist, skip
Security restored
All done!
Connect phone on selected interface...
Reset UserCode ( UserData Safe ) :
Code:
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 26 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 65BD69193D6263B76xxxxxxxxxxxxx
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
BROM/BL stage done
MT626x : Reset User Code
All done! Remove USB cable
All Security Settings deactivated!
Code set to default : 12345
Done!
Connect phone on selected interface...
Read FlashDump :
Code:
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 26 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 65BD69193D6263B762xxxxxxxx
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : DUBAI61D.10.02.11.p1
BROM/BL stage done
Configure RAMINIT Ok
Reading flash now ...
Done!
Control Block Validation (Security Test) :
CBR is Ok, match with BB SN. Phone Security is Alive
Mobile Info
IMEI : 3548870xxxxxx
BBUID : 65BD69193D6263B762A836xxxxxxx
PCCode: 059X8V8
SimLock Info :
STATE : OPENED ( NOT LOCKED )
Dump Saved to : 3548870xxxxxx_MTKx.bin
RPL Saved to : 3548870xxxxxx_MTKx_2nd.mtsec
Read Done!
Connect phone on selected interface...
Recover PhoneBook :
Code:
[MTK] : Extract PhoneBook from file : 3548870xxxxxx_MTKx.bin
[PROCESS] : Sorting Data [1/3]
[PROCESS] : Extract Data [2/3]
[PROCESS] : Decrypt Data [3/3]
[EXTRACT] : Ok, 5 records found!
[INFO] PhoneBook Memory : 500 , Used : 5
CSV Saved to : C:\InfinityBox\BEST\Phones_Data\Readout\3548870814 81584_MTKx.csv
MBAK Saved to : C:\InfinityBox\BEST\Phones_Data\Readout\3548870814 81584_MTKx.csv
[INFO] : MBAK Info :
Create folder "Backup" on SDcard. Put this file in SDcard to folder /Backup/
Inserd card in phone, make "Restore backup" from Settings->Backup
Done
Download Firmware :
Code:
SSChannel : Create SC
SSChannel : SC Created!
ProductID HWCode : RM-1190
Selected Variant : RM-1190 NDT EURO EI WHITE CYRILLIC RU
Firmware Version : 10.02.11
Platform Version : S30+
SSChannel : DC Ok with code 0x0A
Switch to IDM now ...
IDM initializing, wait...
Checking access to Products folder...
Folder for RM-1190 exist
Prepare done, collect info
[Query] : RM1190_059X8V9_10.02.11_001.vpl , 5,96 KiB
[Query] : RM-1190_auth_sv5_eMP.auth , 2,20 KiB
[Query] : RM-1190_CUSTPACK_ROM_EI_EURO_RU_eMP_10.02.11_001 , 75,67 KiB
[Query] : RM-1190_EXT_BOOTLOADER_eMP_10.02.11 , 79,90 KiB
[Query] : RM-1190_JUMP_TABLE_EI_EURO_RU_eMP_10.02.11_001 , 1,15 KiB
[Query] : RM-1190_LANG_PACK_ROM_EI_eMP_10.02.11_001 , 254,18 KiB
[Query] : RM-1190_ROM_eMP_10.02.11 , 551,46 KiB
[Query] : RM-1190_ROOTCERT_Signed_By_MTK_eMP_10.02.11 , 1,32 KiB
[Query] : RM-1190_SECURE_RO_ME_eMP_10.02.11 , 1,59 KiB
[Query] : RM-1190_VIVA_eMP_10.02.11 , 2,39 MiB
Files to download : 10
Total size to download : 3,34 MiB
Downloading now, please, wait...
[Download] : RM1190_059X8V9_10.02.11_001.vpl
[Skip,Exist] : RM-1190_auth_sv5_eMP.auth
[Skip,Exist] : RM-1190_CUSTPACK_ROM_EI_EURO_RU_eMP_10.02.11_001
[Skip,Exist] : RM-1190_EXT_BOOTLOADER_eMP_10.02.11
[Skip,Exist] : RM-1190_JUMP_TABLE_EI_EURO_RU_eMP_10.02.11_001
[Skip,Exist] : RM-1190_LANG_PACK_ROM_EI_eMP_10.02.11_001
[Skip,Exist] : RM-1190_ROM_eMP_10.02.11
[Skip,Exist] : RM-1190_ROOTCERT_Signed_By_MTK_eMP_10.02.11
[Skip,Exist] : RM-1190_SECURE_RO_ME_eMP_10.02.11
[Skip,Exist] : RM-1190_VIVA_eMP_10.02.11
Verify files now ...
[Verify Ok] : RM-1190_ROOTCERT_Signed_By_MTK_eMP_10.02.11
[Verify Ok] : RM-1190_EXT_BOOTLOADER_eMP_10.02.11
[Verify Ok] : RM-1190_SECURE_RO_ME_eMP_10.02.11
[Verify Ok] : RM-1190_ROM_eMP_10.02.11
[Verify Ok] : RM-1190_LANG_PACK_ROM_EI_eMP_10.02.11_001
[Verify Ok] : RM-1190_CUSTPACK_ROM_EI_EURO_RU_eMP_10.02.11_001
[Verify Ok] : RM-1190_JUMP_TABLE_EI_EURO_RU_eMP_10.02.11_001
[Verify Ok] : RM-1190_VIVA_eMP_10.02.11
[Verify Ok] : RM-1190_auth_sv5_eMP.auth
All done, all files were downloaded!
Firmware flashing :
Code:
Core : v2.27 , MTKx FlashEngine : v11.5
Verify files ...
MAUI : RM-1190_ROM_eMP_10.02.11
VIVA : RM-1190_VIVA_eMP_10.02.11
LANG : RM-1190_LANG_PACK_ROM_EI_eMP_10.02.11_001
CUST : RM-1190_CUSTPACK_ROM_EI_EURO_RU_eMP_10.02.11_001
JMPT : RM-1190_JUMP_TABLE_EI_EURO_RU_eMP_10.02.11_001
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 26 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 65BD69193D6263B762Axxxxxxxxx
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : DUBAI61D.10.02.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Dubai.fg
DA_VERIFY : 00
DA_JUMP : 00100000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00EC , [GigaDevice] GD25LQ32
[0] : FLASH_DIE : 00C8 0060 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A0000-0x003F7FFF , LEN : 0x00058000
SecureDecrypt : RM-1190_ROM_eMP_10.02.11
SecureDecrypt : RM-1190_VIVA_eMP_10.02.11
SecureDecrypt : RM-1190_LANG_PACK_ROM_EI_eMP_10.02.11_001
SecureDecrypt : RM-1190_CUSTPACK_ROM_EI_EURO_RU_eMP_10.02.11_001
SecureDecrypt : RM-1190_JUMP_TABLE_EI_EURO_RU_eMP_10.02.11_001
OVRLP : 000069B900000001
PHPID : DUBAI61D.10.02.11.p1
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-1190_ROM_eMP_10.02.11
Write : RM-1190_LANG_PACK_ROM_EI_eMP_10.02.11_001
Write : RM-1190_CUSTPACK_ROM_EI_EURO_RU_eMP_10.02.11_001
Write : RM-1190_JUMP_TABLE_EI_EURO_RU_eMP_10.02.11_001
Write : RM-1190_VIVA_eMP_10.02.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-1190_ROM_eMP_10.02.11
[VERIFY] DONE : RM-1190_LANG_PACK_ROM_EI_eMP_10.02.11_001
[VERIFY] DONE : RM-1190_CUSTPACK_ROM_EI_EURO_RU_eMP_10.02.11_001
[VERIFY] DONE : RM-1190_JUMP_TABLE_EI_EURO_RU_eMP_10.02.11_001
[VERIFY] DONE : RM-1190_VIVA_eMP_10.02.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x003A0000-0x003F7FFF , LEN : 0x00058000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Rebooting phone now
Flashing done!
Total flash time : 00:01:01
Reboot phone Ok
- > Hint : If phone shows Battery charge icon - press and hold PowerOn button 10 seconds
Wait, when phone will be ready ...
Reading Phone Info....
Software Info: 10.02.11 00-00-00 RM-1190
IMEI: 3548870xxxxxxxxx
Ape Version: NEMO G 59cb152c/0 (59cb152c+0) T Mon Jul 1 02:50:44 2013 U 69b804d5
PPM version : EI
Product code: 059X8V8
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Connect phone on selected interface...
Identify :
Code:
Phone found!
MTKx Nokia Phone detected
Read info... Ok
Reading Phone Info....
Software ver : 10.02.11 00-00-00 RM-1190
IMEI 1 : 3548870xxxxxxx
IMEI 2 : 3548870xxxxxxx
XappVer : 000008DE
Ape Ver : NEMO G 59cb152c/0 (59cb152c+0) T Mon Jul 1 02:50:44 2013 U 69b804d5
PPM : EI
CNT : DUBAI61D.10.02.11.p1
Product SN : F85AB38AU
Product code : 059X8V8
Base Prd.code: 059X7J5
Module code : 0207092
Hardware info=======
HWID : 1100
LCDVer: TPO
Lock info ===========
IMEI : 3548870xxxxxx
IMEI spNet : 3A 45 88 xxxx xxxx
Conf key : 800000000004000B
Provider key : 2440700000000000
Country : Finland
Operator : NOKIA (Open)
Lock info:
Block 1
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 2
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 3
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 4
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 5
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 6
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 7
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
SimLock status : Ok
Security status : Ok
Done!
SelfTest :
Code:
Execuring SelfTests
Passed : Camera_If Test
Passed : Display Test
Passed : Keyboard_Short_Circuit Test
Passed : MicroSD_Short_Circuit Test
Passed : Sim_Short_Circuit Test
Passed : Real_Time_Clock Test
Passed : Bluetooth Test
Passed : Audio Test
Passed : Charge Test
Passed : Earpiece Test
Done
Format FS / Reset Settings :
Code:
Software Info: 10.02.11 00-00-00 RM-1190
IMEI: 3548870xxxxxx
PPM version : EI
Product code: 059X8V8
Rebooting phone to FlashMode...
Wait for phone...
Phone found! [ 26 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 65BD69193D6263B7xxxxxxxxxxxxx
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : DUBAI61D.10.02.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Dubai.fg
DA_VERIFY : 00
DA_JUMP : 00100000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00EC , [GigaDevice] GD25LQ32
[0] : FLASH_DIE : 00C8 0060 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A0000-0x003F7FFF , LEN : 0x00058000
Executing FFS FORMAT now...
FAT_RANGE : 0x003A0000-0x003F7FFF , LEN : 0x00058000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Elapsed: 00:00:16
Connect phone on selected interface...
Backup RPL :
Code:
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 26 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 65BD69193D6263B76xxxxxxxxxxxxx
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : DUBAI61D.10.02.11.p1
BROM/BL stage done
Configure RAMINIT Ok
Reading flash now ...
Done!
Control Block Validation (Security Test) :
CBR is Ok, match with BB SN. Phone Security is Alive
Mobile Info
IMEI : 354887081481584
BBUID : 65BD69193D6263B76xxxxxxxxxxxx
PCCode: 059X8V8
SimLock Info :
STATE : OPENED ( NOT LOCKED )
RPL Saved to : 3548870xxxxxxx_MTKx_2nd.mtsec
Read Done!
Connect phone on selected interface...
Write RPL ( with additional fix/edit/repair operations ) :
Code:
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 26 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 65BD69193D6263B76xxxxxxx
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : DUBAI61D.10.02.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Dubai.fg
DA_VERIFY : 00
DA_JUMP : 00100000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00EC , [GigaDevice] GD25LQ32
[0] : FLASH_DIE : 00C8 0060 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A0000-0x003F7FFF , LEN : 0x00058000
Boot Ok
Get settings...
[INFO] : Encrypted RPL
[RPL VERIFY] : Code 0x10 : MOBILE_ID match with MOBILE_ID info in RPL!
Reset SimLock Counters
Reset SimLock Counters Done!
DSPhone : LifeTimer not exist, skip
Security restored
All done!
Connect phone on selected interface...
Reset UserCode ( UserData Safe ) :
Code:
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 26 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 65BD69193D6263B76xxxxxxxxxxxxx
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
BROM/BL stage done
MT626x : Reset User Code
All done! Remove USB cable
All Security Settings deactivated!
Code set to default : 12345
Done!
Connect phone on selected interface...
Read FlashDump :
Code:
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 26 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 65BD69193D6263B762xxxxxxxx
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : DUBAI61D.10.02.11.p1
BROM/BL stage done
Configure RAMINIT Ok
Reading flash now ...
Done!
Control Block Validation (Security Test) :
CBR is Ok, match with BB SN. Phone Security is Alive
Mobile Info
IMEI : 3548870xxxxxx
BBUID : 65BD69193D6263B762A836xxxxxxx
PCCode: 059X8V8
SimLock Info :
STATE : OPENED ( NOT LOCKED )
Dump Saved to : 3548870xxxxxx_MTKx.bin
RPL Saved to : 3548870xxxxxx_MTKx_2nd.mtsec
Read Done!
Connect phone on selected interface...
Recover PhoneBook :
Code:
[MTK] : Extract PhoneBook from file : 3548870xxxxxx_MTKx.bin
[PROCESS] : Sorting Data [1/3]
[PROCESS] : Extract Data [2/3]
[PROCESS] : Decrypt Data [3/3]
[EXTRACT] : Ok, 5 records found!
[INFO] PhoneBook Memory : 500 , Used : 5
CSV Saved to : C:\InfinityBox\BEST\Phones_Data\Readout\3548870814 81584_MTKx.csv
MBAK Saved to : C:\InfinityBox\BEST\Phones_Data\Readout\3548870814 81584_MTKx.csv
[INFO] : MBAK Info :
Create folder "Backup" on SDcard. Put this file in SDcard to folder /Backup/
Inserd card in phone, make "Restore backup" from Settings->Backup
Done
iOS_Shakil
Friend's Martview
Rm-1035 Flash Done
Code:
Connect phone on selected interface...
Core : v2.28 , MTKx FlashEngine : v12.0
Verify files ...
MAUI : RM-1035_ROM_eMP_10.01.11
VIVA : RM-1035_VIVA_eMP_10.01.11
LANG : RM-1035_LANG_PACK_ROM_MS_eMP_10.01.11_001
CUST : RM-1035_CUSTPACK_ROM_MS_MEA_BD_eMP_10.01.11_001
JMPT : RM-1035_JUMP_TABLE_MS_MEA_BD_eMP_10.01.11_001
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 55 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 909F006A95FC1C4A2426F76E0980E008
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : CRYSTAL.10.01.11.p2
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Crystal.fg
DA_VERIFY : 00
DA_JUMP : 00040000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A4000-0x003F3FFF , LEN : 0x00050000
SecureDecrypt : RM-1035_ROM_eMP_10.01.11
SecureDecrypt : RM-1035_VIVA_eMP_10.01.11
SecureDecrypt : RM-1035_LANG_PACK_ROM_MS_eMP_10.01.11_001
SecureDecrypt : RM-1035_CUSTPACK_ROM_MS_MEA_BD_eMP_10.01.11_001
SecureDecrypt : RM-1035_JUMP_TABLE_MS_MEA_BD_eMP_10.01.11_001
OVRLP : 000069B900000001
PHPID : CRYSTAL.10.01.11.p2
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-1035_ROM_eMP_10.01.11
Write : RM-1035_LANG_PACK_ROM_MS_eMP_10.01.11_001
Write : RM-1035_CUSTPACK_ROM_MS_MEA_BD_eMP_10.01.11_001
Write : RM-1035_JUMP_TABLE_MS_MEA_BD_eMP_10.01.11_001
Write : RM-1035_VIVA_eMP_10.01.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-1035_ROM_eMP_10.01.11
[VERIFY] DONE : RM-1035_LANG_PACK_ROM_MS_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_CUSTPACK_ROM_MS_MEA_BD_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_JUMP_TABLE_MS_MEA_BD_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_VIVA_eMP_10.01.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x003A4000-0x003F3FFF , LEN : 0x00050000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Rebooting phone now
Flashing done!
Total flash time : 00:01:04
Reboot phone Ok
Connect phone on selected interface...
maanarman
Friend's Martview
Nokia 130 Write Flash With Best Dongle
Code:
Connect phone on selected interface...
Core : v2.29 , MTKx FlashEngine : v14.0
Verify files ...
MAUI : RM-1035_ROM_eMP_10.01.11
VIVA : RM-1035_VIVA_eMP_10.01.11
LANG : RM-1035_LANG_PACK_ROM_IJ_eMP_10.01.11_001
CUST : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_10.01.11_001
JMPT : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_10.01.11_001
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 41 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 5E82A016051FCFD775484C430A811353
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : CRYSTAL.10.01.11.p2
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Crystal.fg
DA_VERIFY : 00
DA_JUMP : 00040000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A4000-0x003F3FFF , LEN : 0x00050000
SecureDecrypt : RM-1035_ROM_eMP_10.01.11
SecureDecrypt : RM-1035_VIVA_eMP_10.01.11
SecureDecrypt : RM-1035_LANG_PACK_ROM_IJ_eMP_10.01.11_001
SecureDecrypt : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_10.01.11_001
SecureDecrypt : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_10.01.11_001
OVRLP : 000069B900000001
PHPID : CRYSTAL.10.01.11.p2
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-1035_ROM_eMP_10.01.11
Write : RM-1035_LANG_PACK_ROM_IJ_eMP_10.01.11_001
Write : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_10.01.11_001
Write : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_10.01.11_001
Write : RM-1035_VIVA_eMP_10.01.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-1035_ROM_eMP_10.01.11
[VERIFY] DONE : RM-1035_LANG_PACK_ROM_IJ_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_VIVA_eMP_10.01.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x003A4000-0x003F3FFF , LEN : 0x00050000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Rebooting phone now
Flashing done!
Total flash time : 00:01:02
Reboot phone Ok
Connect phone on selected interface...maanarman
Friend's Martview
Nokia 110 Write Flash With Best Dongle
Code:
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm827__03.04.mcusw
PPM : rm827__03.04.ppm_m4
CNT : rm827__03.04.image_m4_059N407
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x0A
IF xCPUID : XGOLD 213 [XMM2130 QUANTUM]
IF Resp Data : 1FB300020303010100FF
Sending EBL Loader ...
EBL Loader Ok, 01
EBL Loader ready, AA
Sending EBL ...
EBL sent Ok
EBL : Quantum_Bootloader_10.49_M1S1
Speed accepted, use 6.500.000
FLASHID : EC001230
FLIC conf set, RST set
Boot done!
Check keys...
Check done. Image can be flashed
Backup enabled, will read all certificates
Reading CCC
Reading HWC
Reading NPC
IMEI 1 : 355510050811149
IMEI 2 : 355510050811156
PCcode : 059N417
NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...
RPL saved : C:\InfinityBox\BEST\Backup\Cert\355510050811149_XG213_CRT.rpl
Settings : EDM [0x8] , Block Mode , Fast CRC , Verify
===Flashing [MCU]===
File : rm827__03.04.mcusw
Image : rm827__03.04.mcusw_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 5 region(s)
Processing Region 1/5
Erase , Start : 0x40000000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40000000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 2/5
Erase , Start : 0x40040000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40040000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 3/5
Erase , Start : 0x40060000 , Len : 0x00100000
Erasing, wait ...
Erase done, time : 00:00:02
Write , Start : 0x40060000 , Len : 0x00100000
Flashing , wait ...
Region flash done, time : 00:00:01
Processing Region 4/5
Erase , Start : 0x40280000 , Len : 0x01940000
Erasing, wait ...
Erase done, time : 00:00:49
Write , Start : 0x40280000 , Len : 0x018C0000
Flashing , wait ...
Region flash done, time : 00:00:37
Processing Region 5/5
Erase , Start : 0x43E20000 , Len : 0x00040000
Erasing, wait ...
Erase done, time : 00:00:00
No write data, skip
CRC check passed , 0x74A0
===Flashing [PPM]===
File : rm827__03.04.ppm_m4
Image : package_m4.ppm_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x41BC0000 , Len : 0x00600000
Erasing, wait ...
Erase done, time : 00:00:06
Write , Start : 0x41BC0000 , Len : 0x00380998
Flashing , wait ...
Region flash done, time : 00:00:05
CRC check passed , 0xA432
===Flashing [CNT]===
File : rm827__03.04.image_m4_059N407
Image : package_m4_059N407.image.fls
Sec-pack found, sending ...
Sec-pack sent
Found 2 region(s)
Processing Region 1/2
Erase , Start : 0x421C0000 , Len : 0x01C60000
Erasing, wait ...
Erase done, time : 00:01:08
Write , Start : 0x421C0000 , Len : 0x00DE0000
Flashing , wait ...
Region flash done, time : 00:00:20
Processing Region 2/2
Erase , Start : 0x43E60000 , Len : 0x000E0000
Erasing, wait ...
Erase done, time : 00:00:02
No write data, skip
CRC check passed , 0xED62
Flashing done!
Total flash time : 00:03:15
Reboot phone now...
Reading Phone Info....
Connected phone - Nokia 110
Software Info: V 03.04 20-04-12 RM-827 (c) Nokia
IMEI: 355510050811149
PPM version : V 03.04 20-04-12 RM-827 (c) Nokia M4
Product code: 059N417
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Processing After Flash Defaults...
FullFactorySet... Ok!
UserDataDefaultsSet...OK!
ServiceDefaultsSet... Ok!
LeaveDefaultsSet... Ok!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Check and Upload User Certificates ...
Total - 42 certs
Certificates found, skip upload ...
Set phone to Normal mode...
AfterFlash operations done ;D
Done!
Connect phone on selected interface...
Elapsed: 00:04:07
Connect phone on selected interface...maanarman
Friend's Martview
Nokia 130 Reset Phone Lock
Code:
Connect phone on selected interface...
Phone found!
MTKx Nokia Phone detected
Read info... Ok
Software Info: 10.01.11 00-00-00 RM-1035
IMEI: 355760069864221
PPM version : IJ
Product code: 059W037
Rebooting phone to FlashMode...
Wait for phone...
Phone found! [ 41 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 05828AA1533E8C63146E427487E9DFEC
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
BROM/BL stage done
MT626x : Reset User Code
All done! Remove USB cable
All Security Settings deactivated!
Code set to default : 12345
Done!
Connect phone on selected interface...maanarman
Friend's Martview
Nokia 225 Write Flash With Best Dongle
Code:
Core : v2.29 , MTKx FlashEngine : v14.0
Verify files ...
MAUI : RM-1011_ROM_eMP_30.06.11
VIVA : RM-1011_VIVA_eMP_30.06.11
LANG : RM-1011_LANG_PACK_ROM_IJ_eMP_30.06.11_001
CUST : RM-1011_CUSTPACK_ROM_IJ_MEA_PK_eMP_30.06.11_001
JMPT : RM-1011_JUMP_TABLE_IJ_MEA_PK_eMP_30.06.11_001
- > MODE : FullFlash
Software Info: 10.01.11 00-00-00 RM-1011
IMEI: 353649064638080
PPM version : IJ
Product code: 059V5V2
Rebooting phone to FlashMode...
Wait for phone...
Phone found! [ 41 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 8B5EFDF96FF38CC551EDDD01DCE920C3
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : PEARL.10.01.11.p2
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Pearl.fg
DA_VERIFY : 00
DA_JUMP : 00040000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00EF , [MXIC] MX25U12835FZNI_10G
[0] : FLASH_DIE : 00C2 0025 0038 0000
[0] : FLASH_LEN : 0x01000000
FAT_RANGE : 0x00C80000-0x00FF3FFF , LEN : 0x00374000
SecureDecrypt : RM-1011_ROM_eMP_30.06.11
SecureDecrypt : RM-1011_VIVA_eMP_30.06.11
SecureDecrypt : RM-1011_LANG_PACK_ROM_IJ_eMP_30.06.11_001
SecureDecrypt : RM-1011_CUSTPACK_ROM_IJ_MEA_PK_eMP_30.06.11_001
SecureDecrypt : RM-1011_JUMP_TABLE_IJ_MEA_PK_eMP_30.06.11_001
OVRLP : 000069B900000001
PHPID : PEARL.10.01.11.p2
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-1011_ROM_eMP_30.06.11
Write : RM-1011_LANG_PACK_ROM_IJ_eMP_30.06.11_001
Write : RM-1011_CUSTPACK_ROM_IJ_MEA_PK_eMP_30.06.11_001
Write : RM-1011_JUMP_TABLE_IJ_MEA_PK_eMP_30.06.11_001
Write : RM-1011_VIVA_eMP_30.06.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-1011_ROM_eMP_30.06.11
[VERIFY] DONE : RM-1011_LANG_PACK_ROM_IJ_eMP_30.06.11_001
[VERIFY] DONE : RM-1011_CUSTPACK_ROM_IJ_MEA_PK_eMP_30.06.11_001
[VERIFY] DONE : RM-1011_JUMP_TABLE_IJ_MEA_PK_eMP_30.06.11_001
[VERIFY] DONE : RM-1011_VIVA_eMP_30.06.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x00C80000-0x00FF3FFF , LEN : 0x00374000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Rebooting phone now
Flashing done!
Total flash time : 00:03:14
Reboot phone Ok
Connect phone on selected interface...maanarman
Friend's Martview
Nokia 210 Write Flash WIth Best dongle
Code:
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm924__04.12.mcusw
PPM : rm924__04.12.ppm_ma3
CNT : rm924__04.12.image_ma3_059T632
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x0A
IF xCPUID : XGOLD 213 [XMM2130 QUANTUM]
IF Resp Data : 1FB300020303010100FF
Sending EBL Loader ...
EBL Loader Ok, 01
EBL Loader ready, AA
Sending EBL ...
EBL sent Ok
EBL : Quantum_Bootloader_10.56_M1S1
Speed accepted, use 6.500.000
FLASHID : EC001230
FLIC conf set, RST set
Boot done!
Check keys...
Check done. Image can be flashed
Backup enabled, will read all certificates
Reading CCC
Reading HWC
Reading NPC
IMEI 1 : 355514055929989
IMEI 2 : 355514055929997
PCcode : 059R775
NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...
RPL saved : C:\InfinityBox\BEST\Backup\Cert\355514055929989_XG213_CRT.rpl
Settings : EDM [0x8] , Block Mode , Fast CRC , Verify
===Flashing [MCU]===
File : rm924__04.12.mcusw
Image : rm924__04.12.mcusw_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 5 region(s)
Processing Region 1/5
Erase , Start : 0x40000000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40000000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 2/5
Erase , Start : 0x40040000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40040000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 3/5
Erase , Start : 0x40060000 , Len : 0x00100000
Erasing, wait ...
Erase done, time : 00:00:02
Write , Start : 0x40060000 , Len : 0x00100000
Flashing , wait ...
Region flash done, time : 00:00:01
Processing Region 4/5
Erase , Start : 0x40280000 , Len : 0x01A40000
Erasing, wait ...
Erase done, time : 00:00:54
Write , Start : 0x40280000 , Len : 0x01A40000
Flashing , wait ...
Region flash done, time : 00:00:35
Processing Region 5/5
Erase , Start : 0x43E20000 , Len : 0x00040000
Erasing, wait ...
Erase done, time : 00:00:00
No write data, skip
CRC check passed , 0x7DFD
===Flashing [PPM]===
File : rm924__04.12.ppm_ma3
Image : package_ma3.ppm_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x41CC0000 , Len : 0x00640000
Erasing, wait ...
Erase done, time : 00:00:08
Write , Start : 0x41CC0000 , Len : 0x003EE5C4
Flashing , wait ...
Region flash done, time : 00:00:05
CRC check passed , 0x86E8
===Flashing [CNT]===
File : rm924__04.12.image_ma3_059T632
Image : package_ma3_059T632.image.fls
Sec-pack found, sending ...
Sec-pack sent
Found 2 region(s)
Processing Region 1/2
Erase , Start : 0x42300000 , Len : 0x01B20000
Erasing, wait ...
Erase done, time : 00:01:04
Write , Start : 0x42300000 , Len : 0x00C20000
Flashing , wait ...
Region flash done, time : 00:00:16
Processing Region 2/2
Erase , Start : 0x43E60000 , Len : 0x000E0000
Erasing, wait ...
Erase done, time : 00:00:02
No write data, skip
CRC check passed , 0xB2C0
Flashing done!
Total flash time : 00:03:12
Reboot phone now...
Reading Phone Info....
Connected phone - Nokia 210
Software Info: V 04.12 21-05-13 RM-924 (c) Nokia
IMEI: 355514055929989
PPM version : V 04.12 21-05-13 RM-924 (c) Nokia MA3
Product code: 059R775
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Processing After Flash Defaults...
FullFactorySet... Ok!
UserDataDefaultsSet...OK!
ServiceDefaultsSet... Ok!
LeaveDefaultsSet... Ok!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Check and Upload User Certificates ...
Total - 58 certs
Certificates found, skip upload ...
Battery voltage is enough for start
Set phone to Normal mode...
AfterFlash operations done ;D
Done!
Connect phone on selected interface...
Elapsed: 00:04:09
Connect phone on selected interface...maanarman
Friend's Martview
Nokia 216 Reset Phone Lock
Code:
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 41 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 491E0D9AA72899E9F68F819003E836E8
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
BROM/BL stage done
MT626x : Reset User Code
All done! Remove USB cable
All Security Settings deactivated!
Code set to default : 12345
Done!
Connect phone on selected interface...maanarman
Friend's Martview
Nokia 105 Phone Unlock With Best Dongle
Code:
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 36 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 1FFCA133C783CCBF6C22EB8A80F15F87
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
BROM/BL stage done
MT626x : Reset User Code
All done! Remove USB cable
All Security Settings deactivated!
Code set to default : 12345
Done!
Connect phone on selected interface...maanarman
Friend's Martview
Nokia Rm-1190 Write Flash With Best Dongle
Code:
Connect phone on selected interface...
Core : v2.29 , MTKx FlashEngine : v14.0
Verify files ...
MAUI : RM-1190_DUBAI_ROM_eMP_11.00.11
VIVA : RM-1190_DUBAI_VIVA_eMP_11.00.11
LANG : RM-1190_DUBAI_LANG_PACK_ROM_AE_eMP_11.00.11
CUST : RM-1190_DUBAI_CUSTPACK_ROM_AE_eMP_11.00.11
JMPT : RM-1190_DUBAI_JUMP_TABLE_AE_eMP_11.00.11
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 79 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0001
BB_CPU_SN : 9FFA591357A4880B88D0735345C03EEA
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : DUBAI61D.10.02.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Dubai.fg
DA_VERIFY : 00
DA_JUMP : 00100000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x0113 ,
[0] : FLASH_DIE : 00EF 0070 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A0000-0x003F7FFF , LEN : 0x00058000
SecureDecrypt : RM-1190_DUBAI_ROM_eMP_11.00.11
SecureDecrypt : RM-1190_DUBAI_VIVA_eMP_11.00.11
SecureDecrypt : RM-1190_DUBAI_LANG_PACK_ROM_AE_eMP_11.00.11
SecureDecrypt : RM-1190_DUBAI_CUSTPACK_ROM_AE_eMP_11.00.11
SecureDecrypt : RM-1190_DUBAI_JUMP_TABLE_AE_eMP_11.00.11
Executing FFS FORMAT now...
FAT_RANGE : 0x003A0000-0x003F7FFF , LEN : 0x00058000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
OVRLP : 000069B900000001
PHPID : DUBAI61D.10.02.11.p1
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-1190_DUBAI_ROM_eMP_11.00.11
Write : RM-1190_DUBAI_LANG_PACK_ROM_AE_eMP_11.00.11
Write : RM-1190_DUBAI_CUSTPACK_ROM_AE_eMP_11.00.11
Write : RM-1190_DUBAI_JUMP_TABLE_AE_eMP_11.00.11
Write : RM-1190_DUBAI_VIVA_eMP_11.00.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-1190_DUBAI_ROM_eMP_11.00.11
[VERIFY] DONE : RM-1190_DUBAI_LANG_PACK_ROM_AE_eMP_11.00.11
[VERIFY] DONE : RM-1190_DUBAI_CUSTPACK_ROM_AE_eMP_11.00.11
[VERIFY] DONE : RM-1190_DUBAI_JUMP_TABLE_AE_eMP_11.00.11
[VERIFY] DONE : RM-1190_DUBAI_VIVA_eMP_11.00.11
CODE_VERIFY : Ok
Flashing done!
Total flash time : 00:00:53
Reboot phone Ok
ReadInfo can't be done! Re-insert battery and power up phone manually
Connect phone on selected interface...maanarman
Friend's Martview
Nokia 108 Write Flash With Best Dongle
Code:
Connect phone on selected interface...
Core : v2.29 , MTKx FlashEngine : v14.0
Verify files ...
MAUI : RM-944_ROM_eMP_12.06.11
VIVA : RM-944_VIVA_eMP_12.06.11
LANG : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
CUST : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
JMPT : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 41 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0001
BB_CPU_SN : 7AFB1E8A6FC86DA332E85E887547F1E1
BROM Protocol Version : 05
BROM Status : 1012
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : Bree.20.06.11.p4
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Bree.fg
DA_VERIFY : 00
DA_JUMP : 00040000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x88
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A6000-0x003F3FFF , LEN : 0x0004E000
SecureDecrypt : RM-944_ROM_eMP_12.06.11
SecureDecrypt : RM-944_VIVA_eMP_12.06.11
SecureDecrypt : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
SecureDecrypt : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
SecureDecrypt : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
OVRLP : 000069B900000001
PHPID : Bree.20.06.11.p4
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-944_ROM_eMP_12.06.11
Write : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
Write : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
Write : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
Write : RM-944_VIVA_eMP_12.06.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-944_ROM_eMP_12.06.11
[VERIFY] DONE : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
[VERIFY] DONE : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
[VERIFY] DONE : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
[VERIFY] DONE : RM-944_VIVA_eMP_12.06.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x003A6000-0x003F3FFF , LEN : 0x0004E000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Rebooting phone now
Flashing done!
Total flash time : 00:01:00
Reboot phone Ok
Connect phone on selected interface...maanarman
Friend's Martview
Nokia 130 Write Flash With Best Dongle
Code:
Connect phone on selected interface...
Core : v2.29 , MTKx FlashEngine : v14.0
Verify files ...
MAUI : RM-1035_CRYSTAL_ROM_eMP_14.00.11
VIVA : RM-1035_CRYSTAL_VIVA_eMP_14.00.11
LANG : RM-1035_CRYSTAL_LANG_PACK_ROM_IJ_eMP_14.00.11
CUST : RM-1035_CRYSTAL_CUSTPACK_ROM_IJ_eMP_14.00.11
JMPT : RM-1035_CRYSTAL_JUMP_TABLE_IJ_eMP_14.00.11
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 41 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 8DB06839E6C58FC68D47F0C38982E5C5
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : CRYSTAL.10.01.11.p2
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Crystal.fg
DA_VERIFY : 00
DA_JUMP : 00040000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A4000-0x003F3FFF , LEN : 0x00050000
SecureDecrypt : RM-1035_CRYSTAL_ROM_eMP_14.00.11
SecureDecrypt : RM-1035_CRYSTAL_VIVA_eMP_14.00.11
SecureDecrypt : RM-1035_CRYSTAL_LANG_PACK_ROM_IJ_eMP_14.00.11
SecureDecrypt : RM-1035_CRYSTAL_CUSTPACK_ROM_IJ_eMP_14.00.11
SecureDecrypt : RM-1035_CRYSTAL_JUMP_TABLE_IJ_eMP_14.00.11
Executing FFS FORMAT now...
FAT_RANGE : 0x003A4000-0x003F3FFF , LEN : 0x00050000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
OVRLP : 000069B900000001
PHPID : CRYSTAL.10.01.11.p2
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-1035_CRYSTAL_ROM_eMP_14.00.11
Write : RM-1035_CRYSTAL_LANG_PACK_ROM_IJ_eMP_14.00.11
Write : RM-1035_CRYSTAL_CUSTPACK_ROM_IJ_eMP_14.00.11
Write : RM-1035_CRYSTAL_JUMP_TABLE_IJ_eMP_14.00.11
Write : RM-1035_CRYSTAL_VIVA_eMP_14.00.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-1035_CRYSTAL_ROM_eMP_14.00.11
[VERIFY] DONE : RM-1035_CRYSTAL_LANG_PACK_ROM_IJ_eMP_14.00.11
[VERIFY] DONE : RM-1035_CRYSTAL_CUSTPACK_ROM_IJ_eMP_14.00.11
[VERIFY] DONE : RM-1035_CRYSTAL_JUMP_TABLE_IJ_eMP_14.00.11
[VERIFY] DONE : RM-1035_CRYSTAL_VIVA_eMP_14.00.11
CODE_VERIFY : Ok
Flashing done!
Total flash time : 00:00:54
Reboot phone Ok
ReadInfo can't be done! Re-insert battery and power up phone manually
Connect phone on selected interface...maanarman
Friend's Martview
Samsung J327vpp Flash With SM Module
Code:
Port open Ok!
LOKE received!
Prepare Ok!
Enter Setup...
Setup Done!
Try download PIT...
Download PIT Ok!
Start flashing!
Flashing aboot.mbn
Flashing sbl1.mbn
Flashing rpm.mbn
Flashing tz.mbn
Flashing devcfg.mbn
Flashing NON-HLOS.bin
Flashing cmnlib.mbn
Flashing keymaster.mbn
Flashing lksecapp.mbn
Flashing sec.dat
Flashing apdp.mbn
Flashing msadp.mbn
Flashing boot.img
Flashing recovery.img
Flashing system.img.ext4
Flashing persist.img.ext4
Flashing userdata.img.ext4
Flashing modem.bin
Flashing adspso.bin
Flashing cache.img.ext4
Flashing done
Reboot phone...
Phone Disconnectedmaanarman
Friend's Martview
Nokia 108 Flash With Best Dongle
Code:
Connect phone on selected interface...
Core : v2.29 , MTKx FlashEngine : v14.0
Verify files ...
MAUI : RM-944_ROM_eMP_12.06.11
VIVA : RM-944_VIVA_eMP_12.06.11
LANG : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
CUST : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
JMPT : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 41 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0001
BB_CPU_SN : 9A05CFDBBCB91247A0AE99ACCAD0A64E
BROM Protocol Version : 05
BROM Status : 1012
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : Bree.20.06.11.p4
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Bree.fg
DA_VERIFY : 00
DA_JUMP : 00040000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x88
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A6000-0x003F3FFF , LEN : 0x0004E000
SecureDecrypt : RM-944_ROM_eMP_12.06.11
SecureDecrypt : RM-944_VIVA_eMP_12.06.11
SecureDecrypt : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
SecureDecrypt : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
SecureDecrypt : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
OVRLP : 000069B900000001
PHPID : Bree.20.06.11.p4
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-944_ROM_eMP_12.06.11
Write : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
Write : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
Write : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
Write : RM-944_VIVA_eMP_12.06.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-944_ROM_eMP_12.06.11
[VERIFY] DONE : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
[VERIFY] DONE : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
[VERIFY] DONE : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
[VERIFY] DONE : RM-944_VIVA_eMP_12.06.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x003A6000-0x003F3FFF , LEN : 0x0004E000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Rebooting phone now
Flashing done!
Total flash time : 00:01:10
Reboot phone Ok
Connect phone on selected interface...maanarman
Friend's Martview
Nokia 130 Flash With Best Dongle
Code:
Connect phone on selected interface...
Core : v2.29 , MTKx FlashEngine : v14.0
Verify files ...
MAUI : RM-1035_ROM_eMP_10.01.11
VIVA : RM-1035_VIVA_eMP_10.01.11
LANG : RM-1035_LANG_PACK_ROM_IJ_eMP_10.01.11_001
CUST : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_10.01.11_001
JMPT : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_10.01.11_001
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 41 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 1DD994ECA089B7B83D03326979077878
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : CRYSTAL.10.01.11.p2
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Crystal.fg
DA_VERIFY : 00
DA_JUMP : 00040000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A4000-0x003F3FFF , LEN : 0x00050000
SecureDecrypt : RM-1035_ROM_eMP_10.01.11
SecureDecrypt : RM-1035_VIVA_eMP_10.01.11
SecureDecrypt : RM-1035_LANG_PACK_ROM_IJ_eMP_10.01.11_001
SecureDecrypt : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_10.01.11_001
SecureDecrypt : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_10.01.11_001
OVRLP : 000069B900000001
PHPID : CRYSTAL.10.01.11.p2
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-1035_ROM_eMP_10.01.11
Write : RM-1035_LANG_PACK_ROM_IJ_eMP_10.01.11_001
Write : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_10.01.11_001
Write : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_10.01.11_001
Write : RM-1035_VIVA_eMP_10.01.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-1035_ROM_eMP_10.01.11
[VERIFY] DONE : RM-1035_LANG_PACK_ROM_IJ_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_CUSTPACK_ROM_IJ_MEA_PK_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_JUMP_TABLE_IJ_MEA_PK_eMP_10.01.11_001
[VERIFY] DONE : RM-1035_VIVA_eMP_10.01.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x003A4000-0x003F3FFF , LEN : 0x00050000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Rebooting phone now
Flashing done!
Total flash time : 00:01:02
Reboot phone Ok
Connect phone on selected interface...
Code:
maanarman
Friend's Martview
Nokia 220 Write FLash WIth Best Dongle
Code:
Connect phone on selected interface...
Core : v2.29 , MTKx FlashEngine : v14.0
Verify files ...
MAUI : RM-969_ROM_eMP_10.03.11
VIVA : RM-969_VIVA_eMP_10.03.11
LANG : RM-969_LANG_PACK_ROM_IJ_eMP_10.03.11
CUST : RM-969_CUSTPACK_ROM_IJ_MEA_IR_eMP_10.03.11
JMPT : RM-969_JUMP_TABLE_IJ_MEA_IR_eMP_10.03.11
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 41 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0001
BB_CPU_SN : F9386F344E0F48773CEEC9C417C56B80
BROM Protocol Version : 05
BROM Status : 1012
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : Rivendell.20.14.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Rivendell.fg
DA_VERIFY : 00
DA_JUMP : 00040000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x88
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00F8 , [WINBOND] W25Q128FW
[0] : FLASH_DIE : 00EF 0060 0018 0000
[0] : FLASH_LEN : 0x01000000
FAT_RANGE : 0x00A60000-0x00FF3FFF , LEN : 0x00594000
SecureDecrypt : RM-969_ROM_eMP_10.03.11
SecureDecrypt : RM-969_VIVA_eMP_10.03.11
SecureDecrypt : RM-969_LANG_PACK_ROM_IJ_eMP_10.03.11
SecureDecrypt : RM-969_CUSTPACK_ROM_IJ_MEA_IR_eMP_10.03.11
SecureDecrypt : RM-969_JUMP_TABLE_IJ_MEA_IR_eMP_10.03.11
OVRLP : 000069B900000001
PHPID : Rivendell.20.14.11.p1
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-969_ROM_eMP_10.03.11
Write : RM-969_LANG_PACK_ROM_IJ_eMP_10.03.11
Write : RM-969_CUSTPACK_ROM_IJ_MEA_IR_eMP_10.03.11
Write : RM-969_JUMP_TABLE_IJ_MEA_IR_eMP_10.03.11
Write : RM-969_VIVA_eMP_10.03.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-969_ROM_eMP_10.03.11
[VERIFY] DONE : RM-969_LANG_PACK_ROM_IJ_eMP_10.03.11
[VERIFY] DONE : RM-969_CUSTPACK_ROM_IJ_MEA_IR_eMP_10.03.11
[VERIFY] DONE : RM-969_JUMP_TABLE_IJ_MEA_IR_eMP_10.03.11
[VERIFY] DONE : RM-969_VIVA_eMP_10.03.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x00A60000-0x00FF3FFF , LEN : 0x00594000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Rebooting phone now
Flashing done!
Total flash time : 00:02:46
Reboot phone Ok
Connect phone on selected interface...maanarman
Friend's Martview
Nokia 220 Write Flash With Best Dongle
Code:
Connect phone on selected interface...
Core : v2.29 , MTKx FlashEngine : v14.0
Verify files ...
MAUI : RM-969_ROM_eMP_10.03.11
VIVA : RM-969_VIVA_eMP_10.03.11
LANG : RM-969_LANG_PACK_ROM_IJ_eMP_10.03.11
CUST : RM-969_CUSTPACK_ROM_IJ_MEA_IR_eMP_10.03.11
JMPT : RM-969_JUMP_TABLE_IJ_MEA_IR_eMP_10.03.11
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 41 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0001
BB_CPU_SN : 78A79B5592740C1A06288E1164249157
BROM Protocol Version : 05
BROM Status : 1012
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : Rivendell.10.03.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Rivendell.fg
DA_VERIFY : 00
DA_JUMP : 00040000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x88
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00F8 , [WINBOND] W25Q128FW
[0] : FLASH_DIE : 00EF 0060 0018 0000
[0] : FLASH_LEN : 0x01000000
FAT_RANGE : 0x00A60000-0x00FF3FFF , LEN : 0x00594000
SecureDecrypt : RM-969_ROM_eMP_10.03.11
SecureDecrypt : RM-969_VIVA_eMP_10.03.11
SecureDecrypt : RM-969_LANG_PACK_ROM_IJ_eMP_10.03.11
SecureDecrypt : RM-969_CUSTPACK_ROM_IJ_MEA_IR_eMP_10.03.11
SecureDecrypt : RM-969_JUMP_TABLE_IJ_MEA_IR_eMP_10.03.11
OVRLP : 000069B900000001
PHPID : Rivendell.10.03.11.p1
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-969_ROM_eMP_10.03.11
Write : RM-969_LANG_PACK_ROM_IJ_eMP_10.03.11
Write : RM-969_CUSTPACK_ROM_IJ_MEA_IR_eMP_10.03.11
Write : RM-969_JUMP_TABLE_IJ_MEA_IR_eMP_10.03.11
Write : RM-969_VIVA_eMP_10.03.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-969_ROM_eMP_10.03.11
[VERIFY] DONE : RM-969_LANG_PACK_ROM_IJ_eMP_10.03.11
[VERIFY] DONE : RM-969_CUSTPACK_ROM_IJ_MEA_IR_eMP_10.03.11
[VERIFY] DONE : RM-969_JUMP_TABLE_IJ_MEA_IR_eMP_10.03.11
[VERIFY] DONE : RM-969_VIVA_eMP_10.03.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x00A60000-0x00FF3FFF , LEN : 0x00594000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Rebooting phone now
Flashing done!
Total flash time : 00:03:01
Reboot phone Ok
Connect phone on selected interface...maanarman
Friend's Martview
Nokia 108 Write Flash With Best Dongle
Code:
Connect phone on selected interface...
Core : v2.29 , MTKx FlashEngine : v14.0
Verify files ...
MAUI : RM-944_ROM_eMP_12.06.11
VIVA : RM-944_VIVA_eMP_12.06.11
LANG : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
CUST : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
JMPT : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 41 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0001
BB_CPU_SN : 35EBA4539AA8786F78C499B957DD3C69
BROM Protocol Version : 05
BROM Status : 1012
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : Bree.20.06.11.p4
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Bree.fg
DA_VERIFY : 00
DA_JUMP : 00040000
DA_AUTH : Passed!
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x88
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A6000-0x003F3FFF , LEN : 0x0004E000
SecureDecrypt : RM-944_ROM_eMP_12.06.11
SecureDecrypt : RM-944_VIVA_eMP_12.06.11
SecureDecrypt : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
SecureDecrypt : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
SecureDecrypt : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
OVRLP : 000069B900000001
PHPID : Bree.20.06.11.p4
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-944_ROM_eMP_12.06.11
Write : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
Write : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
Write : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
Write : RM-944_VIVA_eMP_12.06.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-944_ROM_eMP_12.06.11
[VERIFY] DONE : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
[VERIFY] DONE : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
[VERIFY] DONE : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
[VERIFY] DONE : RM-944_VIVA_eMP_12.06.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x003A6000-0x003F3FFF , LEN : 0x0004E000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Rebooting phone now
Flashing done!
Total flash time : 00:01:02
Reboot phone Ok
Connect phone on selected interface...